Summary of the content on the page No. 1
R
PLCD27
WNER'S MANUAL
CD PLAYER
Car Audio Hifi System
Summary of the content on the page No. 2
Band Band tuner Power Direct access tuning Volume play/pause eject clock loud release Radio wiring Speaker wiring Volume setting Install the unit bass setting Removing the unit treble settting balance setting fader setting Top scan repeat random stop 1
Summary of the content on the page No. 3
To prevent injury of fire,take the To prevent damage to the machine, Attaching panel following precautions: take the following precautions: Attach the front panel by fixing the left side of it into this unit as1 Insert the unit unitll it is firmly locked to the Be sure the unit is connected to a 12V showing.Then push the right side main unit, otherwise it may DC power with a Negative Ground of panel towards into connecting fall out of place when jolted The unit is only designed for use with 4 pl
Summary of the content on the page No. 4
VOL+ POWER ON/ Volume EJECT PLAY/PAUSE OFF/VOLUME Increasing volume EJECT Rotate the [VOL+]button VOL Decreasing BD CD PUSH Rotate the [VOL-]button ON/OFF TOP SCAN REPEAT RANDOM STOP DSP 1 2 34 5 6 CLK SELECT CLOCK RELEASE SELECT DSP Play/pause Play Press the [CD]button LCD display Pause Press again the [CD]button Power If a disc has already been loaded, CDIN would be shown on Turning ON the power the display, press this button to start play disc even though the unit is in Radio mode. When disc
Summary of the content on the page No. 5
Hour Eject Press [ ] button to adjust the hour. Out Minute Press the [ ]button ,if having adisc in the unit. Press [ ] button to adjust the minute. The disc will be ejected out. Quit clock set mode In If there no operation in 5 second, it will quit clock Press the [ ]button again, the disc set mode. will be load in. In beam mode, press the BD button can enter radio mode. If the disc in the slot, press the EJECT button to LOUD/DSP eject the disc form the slot and automatically be LOUD switched to
Summary of the content on the page No. 6
VOL+ PRESS PRESS VOL+/- Speaker mode EJECT VOL VOLUME BASS TREBLE BD CD PUSH ON/OFF TOP SCAN REPEAT RANDOM STOP DSP CLK SELECT 1 2 34 5 6 FADER BALANCE SCAN RANDOM SELECT TOP REPEAT STOP In press mode, VOL is sel function Treble set mode Volume set mode Press SEL button third, Press SEL button once,display shows VOL , display shows TRE ,then then rotate the volume + button rotate the volume + button to adjust treble to adjust volume level up.Rotate VOL level up. Rotate the volume - buttonto adju
Summary of the content on the page No. 7
Top Scan Press [TOP]button Press [SCN]button Select the first track directly Press this button once for TRACK INTRODUCTION,the first In CD mode,press this button, the first track will play. ten seconds of each track on the disc will paly. To confirm the track number. Press it again while playing on the desired track. SCAN will appear on the display.Press it again to stop it. Repeat Press [RPT]button Stop Press the button once to repeat the same track continuously, Press [STOP]button Press the bu
Summary of the content on the page No. 8
SEEK- SEEK+ Tune In radio mode: EJECT manual tuning: VOL short press button it can select higher frequency station. BD CD Short press can select lower frequency station. PUSH ON/OFF TOP SCAN REPEAT RANDOM STOP DSP 1 2 34 5 6 CLK SELECT Auto loading tuning: the long press button it can automatically select higher BAND PRESET MEMORY 1-6 frequency station. And the long press it can automatically select lower frequency station. Band Selecting band Press BAND button to select among three FM or two AM
Summary of the content on the page No. 9
Loading and replacing the battery Use one lithium battery(CR2025) insert the batteries with the +and - poles aligned properly. Following the illustration inside the case. Pull out APS MONO LOUD CLK STOP TOP Store unused batteries out of the reach of children. Contact a doctor immediately if the battery is accidentally swallowed. RPT Do not set the remote on hot places such as above the dashboard. SCAN Basic operation RDM Turning ON the power Press the [ ]button. Press to turn on the unit power,P
Summary of the content on the page No. 10
External view External view Volume ........ Number of items ........ Number of items Increasing volume Press the [+]loud VOL Increasing volume 1 ............1 5 ............1 Press the [-]low VOL Play/pause 6 2 ............1 ............1 Play Press the [ ]button Pause 3 ............1 7 ............1 Press the [ ] button again APS MONO LOUD CLK STOP TOP RPT SCAN RDM ............1 8 4 ............2 Radio control Page(7) The use of any accessories except of those provided might result in damage to
Summary of the content on the page No. 11
Follow this easy wiring diagram in order to enable you to install SPEAKER WIRING the new or existing RADIO and SPEAKER wring system. Theunitisonlydesignedforthe usewith4speakerssystem,itcan Be sure the unit is connected to a 12 volts battery with negative ground. only be connected with speakers rated in the load impedance range Good ground connections eliminate most electrical noise problem and from 4 to 8 ohms. Load impedance less than 4 ohms could damage require tight with the metal vehicle ch
Summary of the content on the page No. 12
Before installing the receiver permanently, fit it in the approximate place in your car Connect the equipment according to the speakers and electrical connections. When your system is operated properly,(preferably with the car engine running), follow the instructions 3)Support strap (supplied) for permanent installation of your system. INSTALL THE UNIT 1)Install half sleeve, can be with or without adapter. It will fit better with adapter. 2)Bend over some tabs where possible 2)Bend over tabs tos
Summary of the content on the page No. 13
Specifications subject to change without notice. CD PLAYER GENERAL Signal/Noise radio......................................................70dB Operating power.....................................12 Volts DC,negative Frequency response..............................20Hz-20KHz(+3dB) ground Channel separation..................................................>45dB %10THD output wiring.........................Designed for using four Dual D/A converter..................................................
Summary of the content on the page No. 14
What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. ?No/Poor sound on one or more speakers Before calling service, first check the following table Speakers or speaker wiring or volume, Balance and for possible problems. Fader setting Check the speaker wiring and test the speakers all in good condition check the setting of volume, Balance and Fader controls. ?The power does not turn ON. The fuse has blown. Install half sleeve, can be with o
Summary of the content on the page No. 15
CD PLAYER Car Audio Hifi System
