Summary of the content on the page No. 1
HOMEOWNERS CARE AND
OPERATION INSTRUCTIONS
FREESTANDING
VENTED GAS
FIRED ROOM
HEATERS
Model CI1500DVF Series
Model CI2500DVF Series
Report No. 116-S-08-5
Serefi na Series Direct Vent Gas Stoves
P/N 775,148M Rev. B, 11/04
WARNING: IF THE INFORMATION IN THIS MANUAL AVERTISSEMENT: ASSUREZ-VOUS DE BIEN SUIVRE
LES INSTRUCTIONS DONNÉ DANS CETTE NOTICE
IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLO-
POUR RÉDUIRE AU MINIMUM LE RISQUE D’INCENDIE
SION MAY RESULT CAUSING PROPERTY DAMAGE,
OU POUR ÉVITER TOU
Summary of the content on the page No. 2
GENERAL INFORMATION CONGRATULATIONS ON THE PURCHASE OF YOUR NEW GAS APPLIANCE MANU- FACTURED BY LENNOX HEARTH PRODUCTS. Note: Installation and repair should be performed by a qualifi ed service person. The appliance When you purchased your new gas fi red heater, you joined the ranks of thousands of should be inspected annually by a qualifi ed concerned individuals whose answer to their home heating needs refl ects their concern for professional service technician. More frequent aesthetics, ef
Summary of the content on the page No. 3
I O O L I P T O it TPTH TP TH L I P F L F O Always keep the appliance area clear and free Tables 3 and 4 show the units' gas pressure CARBON MONOXIDE POISONING: EARLY from combustible materials, gasoline and other requirements SIGNS OF CARBON MONOXIDE POISONING fl ammable liquids. ARE SIMILAR TO THE FLU WITH HEADACHES, Remember, Millivolt appliances have a continu- Inlet Gas Supply Pressure DIZZINESS AND/OR NAUSEA. IF YOU HAVE ous burning pilot fl ame. Exercise caution when (all models) TH
Summary of the content on the page No. 4
(Model Serefi na, Black Paint) Do not attempt to • Initial curing of the high temperature paint Lighting Millivolt Appliances repaint the stove until the paint is completely and burning off of lubricants used in the cured. If the surface later becomes stained or To light millivolt appliances refer to the detailed manufacturing process may result in a fi lm marred, it may be lightly sanded and touched on the glass. lighting instructions found on page 13 (English) up with spray paint (See
Summary of the content on the page No. 5
MAINTENANCE SCHEDULE Anually (Before the onset of the Burning Season) Maintenance Task Accomplishing Person Procedure Inspecting/Cleaning Burner, Logs Qualifi ed Service Technician Inspect valve and ensure it is properly operating. Check piping and Controls for leaks. Vacuum the control compartment, fi replace logs and burner area. Check Flame Patterns and Flame Qualifi ed Service Technician Refer to Figure 7 on Page 6 and verify the fl ame pattern and Height height displayed by the appliance c
Summary of the content on the page No. 6
2. Locate and open the 2 latches as shown in Burner Adjustments Front Glass Enclosure Panel, Removal Figure 4 (locate below the stove body). and Installation. The following paragraphs address burner adjustment concerns and procedures. WARNING: NEVER OPERATE THE APPLIANCE WITHOUT THE GLASS ENCLOSURE PANEL Flame Appearance and Sooting: IN PLACE AND SECURE. DO NOT OPERATE Generally most people prefer the warm glow of APPLIANCE WITH THE FRONT GLASS PANEL a yellow to orange fl ame. Applianc
Summary of the content on the page No. 7
Air Shutter Adjustment Guidelines: ENSURE THAT THE FRONT GLASS PANEL IS IN Burner Air Shutter Adjustment PLACE AND SEALED DURING ADJUSTMENT. If the burner fl ame appearance differs greatly Adjusting Set Screw from what is shown on page 6 (see Burner Adjustment Flame Appearance), some adjustment from Adjustment Rod Up (1/8" Open Position) the factory setting for the air shutter gap may CAUTION: THE ADJUSTMENT ROD AND Burner Tube be necessary (to compensate for variables in NEARBY APPLIAN
Summary of the content on the page No. 8
2. Place the largest log onto the rear log Log Placement stoppers (see Figure 9). Ensure that the grooves on the bottom of the log aligns WARNING: LOGS GET VERY HOT AND onto the corresponding places on the rear WILL REMAIN HOT UP TO ONE HOUR log stoppers. Push the log back so that it is against the back of the rear log stoppers AFTER GAS SUPPLY IS TURNED OFF. (see Figure 10). HANDLE ONLY WHEN LOGS ARE COOL. TURN OFF ALL ELECTRICITY TO THE APPLIANCE BEFORE YOU INSTALL Right Front L
Summary of the content on the page No. 9
9. Place the glowing embers on the burner Small Area Paint Touch-up SIT Millivolt Appliance Checkout as shown in fi gures 17 & 18. (Black Painted Stoves Only) The pilot fl ame should be steady, not lifting or fl oating. Flame should be blue in color with One package of ember material has been The stove body is painted with a quality high- traces of orange at the outer edge. The top 3/8" included with this log set You will not need temperature stove paint. Only use factory sup- (10 mm) at the p
Summary of the content on the page No. 10
TH TH TP TP WIRING DIAGRAMS Wiring diagrams are provided here for reference purposes only. This information is also provided on schematics attached directly to the appliance on a pullout panel located within the control compartment. CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DAN- GEROUS APPLIANCE OPERATION. Blower Wiring Diagram Optional Room Air Blower SIT Millivolt Wiring Diagram IMPORTANT: Ground supply wire must be If a
Summary of the content on the page No. 11
Deluxe Remote Control System Flame Modulating Remote Control ACCESSORY COMPONENTS System The Model RCL-T (Deluxe) Remote Control Standard Remote Control System System has all of the features of the standard The Model RCL-MN & RCL-ML remote controls system along with an added easy to read LCD have on and off burner control, fl ame height The Model RCL (Standard) Remote Control screen which presents access to many enhance- adjustment, thermostat operation and a timer System, features a si
Summary of the content on the page No. 12
ACCESSORY COMPONENTS CONTINUED Warming Shelves Brickaded Liner Kits These attactive warming shelves are designed to be functional for The brickade liner kits include panels for the rear and side walls of the placing food to stay warm. The shelves extend on both sides of the fi rebox. The panels have brick-like features in relief. These kits can be stove top and add an attractive accent. See back page for installation retrofi tted into previously installed appliances. instructions. H0773 BL
Summary of the content on the page No. 13
I O O L I P T O i it t TPTH TP TH L I P F L F O LIGHTING INSTRUCTIONS – SIT MILLIVOLT GAS VALVE FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. A. This appliance has a pilot which must be lighted with a • Do not use any phone in your building. piezo igniter. When lighting the pilot, follow these instructions • Immediately call your gas supplier from a neighbo
Summary of the content on the page No. 14
I O O L I P T O it it TPTH TP TH L I P F L F O INSTRUCTIONS D’ALLUMAGE – VANNE GAZ MILLIVOLT SIT POUR VOTRE SÉCURITÉ, LISEZ CES INSTRUCTIONS AVANT L’ALLUMAGE AVERTISSEMENT : SI VOUS NE SUIVEZ PAS CES INSTRUCTIONS À LA LETTRE, IL POURRAIT S’EN SUIVRE UN INCENDIE OU UNE EXPLOSION CAUSANT DES DOMMAGES MATÉRIELS, DES BLESSURES CORPORELLES OU MÊME DES PERTES DE VIE. • Appelez immédiatement votre compagnie de gaz en utilisant le télé- A. Cet appareil est muni d’une veilleuse qui doit être allumée a
Summary of the content on the page No. 15
TROUBLESHOOTING THE MILLIVOLT GAS CONTROL SYSTEM Note: Before troubleshooting the gas control system, be sure external gas shut off valve (located at gas supply inlet) is in the “ON” position. Important: Valve system troubleshooting should only be accomplished by a qualifi ed service technician. SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION 1. Spark igniter will not light pilot after A. Defective igniter Check the gap between the electrode and pilot. It should repeated triggering of igniter button.
Summary of the content on the page No. 16
REPLACEMENT PARTS LIST Gas Controls Item # Part/Cat. No. Description Where Used 1 H1657 Valve Assembly – Natural Gas, SIT All 30 H2211 Gas Train Assembly, MV, Natural Gas (LP units will also require LB-102158A) CI1500DVF Series 30 H2212 Gas Train Assembly, MV, Natural Gas (LP units will also require LB-102158B) CI2500DVF Series 2 111061 Piezo Igniter, Push Button All 3 69L1701 Pilot Assembly, Natural Gas All 5 LB-92706 Pilot Shield All 6 74L5601 Pilot Tube All RB Regulator (
Summary of the content on the page No. 17
REPLACEMENT PARTS LIST Cast Body Components (continued) Item # Part/Cat. No. Description Where Used 20 66M69 Door Casting, Left Front - Enamel Hunter Green, 1 ea. CI1506DVF 20 H1015 Door Casting, Left Front - Enamel Hunter Green, 1 ea. CI2506DVF 20 H2165 Door Casting, Left Front - Enamel Ivory White, 1 ea. CI1508DVF-2 20 H2166 Door Casting, Left Front - Enamel Ivory White, 1 ea. CI2508DVF-2 20 66M68 Door Casting, Left Front - Enamel Maj. Brown, 1 ea. CI1504DVF 20 H1014 Door Casting, Lef
Summary of the content on the page No. 18
REPLACEMENT PARTS Cast Body Components (continued) Item # Part/Cat. No. Description Where Used 25 H1007 Side Casting, Left - Enamel Hunter Green, 1 ea. CI1506DVF 25 H1031 Side Casting, Left - Enamel Hunter Green, 1 ea. CI2506DVF 25 H2174 Side Casting, Left - Enamel Ivory White, 1 ea. CI1508DVF-2 25 H2175 Side Casting, Left - Enamel Ivory White, 1 ea. CI2508DVF-2 25 H1006 Side Casting, Left - Enamel Maj. Brown, 1 ea. CI1504DVF 25 H1030 Side Casting, Left - Enamel Maj. Brown, 1 ea. CI250
Summary of the content on the page No. 19
REPLACEMENT PARTS 1 11 19 L E N N O X 30 4 12 25 2 L E N N O X 13 14 24 26 5 27 7 8 3 15 6 28 20 21 18 23 9 Front View * * * 22 Log Set Does Not Include Ember Strip (purchased 29 16 separately) 17 10 Front View * * * * * * 29b NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 19
Summary of the content on the page No. 20
REFERENCE INFORMATION 4. Place the insets (4 ea. for the CI1500 series or 6 ea. for the CI2500 series) into the recessed areas on both warming shelves as shown in If Optional Warming Shelves are purchased, install as follows: Figures 23 & 24. Note: Common ceramic tiles (4 ¼” square) can be used in place of insets on the warming shelves (available at most Optional Warming Shelves Kit home improvement stores). Kit Contents: 2 ea. Warming Shelves Install Insets 4 ea. Decorative Brackets 4 ea
