Summary of the content on the page No. 1
DVG-2101S
VoIP Telephone Adapter
User Manual
Version 1.00
November 5, 2007
Summary of the content on the page No. 2
Table of Contents INTRODUCTION ............................................................................................................................................... 1 PACKAGE CONTENTS....................................................................................................................................... 1 FEATURES....................................................................................................................................................... 2
Summary of the content on the page No. 3
Introduction DVG-2101S User Manual Introduction The D-LINK DVG-2101S VoIP Telephone Adapter links conventional telephony devices such as analog phones or fax machines to IP networks. The DVG- 2101S includes one Ethernet port and one RJ-11 telephone jack that provide voice communication over the IP network. The Ethernet port is for a DSL/Cable Modem or other WAN (Wide Area Network) devices. It can be configured and monitored using a web browser. This VoIP Telephone Adapter can red
Summary of the content on the page No. 4
DVG-2101S User Manual Introduction Features WAN support One 10/100Mbps auto-MDI/MDIX Ethernet port WAN Type: Static IP, Dynamic IP, and PPPoE MAC Address Clone NAT Traversal: Outbound Proxy, STUN Dynamic DNS support: DlinkDdns, DynDns VLAN ID Tag QoS: IP Precedence NTP Management Web-base, Telnet, and telephone keypad configuration (dial prefix) Built-in Ping Tool Remote firmware upgrade via TFTP, HTTP, HTTPS, and FTP Multi-function reset button: IVR, reset , re
Summary of the content on the page No. 5
Introduction DVG-2101S User Manual SIP NAT Keep Alive Time VPN Flash Hook Timer Adaptive jitter buffer Programmable gain control In-band DTMF Out-of-band DTMF relay: RFC2833/ SIP info DTMF Termination Impedance: 600/900& complex Impedance Failover SIP Proxy server registrations T.30 FAX pass through, T.38 real time FAX relay Caller ID: DTMF, FSK-Bellcore, FSK-ETSI detection and generation by country select Telephone book Voice Codec Feature: G.711 u-law/a-law,
Summary of the content on the page No. 6
DVG-2101S User Manual Introduction Front Panel Phone LED This LED will light solid when the Power LED telephone is off-hook. A fast blinking This LED will light solid when the LED indicates an incoming call and a device finishes a self-test and slow blinking LED indicates a booting up. This LED will flash message is waiting. This LED will during device self-test and booting light off if the phone connected to the and light off if the self-test fails. phone port i
Summary of the content on the page No. 7
Introduction DVG-2101S User Manual Rear Panel Reset Button Use a paper clip to: 1. Press 1-2 seconds to enable IVR. Power Receptor 2. Press 4-6 seconds to reset this unit. Connects to the 3. Press 8-10 seconds to restore this unit’s provided power factory default settings. adapter. Phone Port WAN Port Connects to your phone Connects to your using a standard phone broadband modem using cable (RJ-11). an Ethernet cable. 5
Summary of the content on the page No. 8
DVG-2101S User Manual Hardware Installation Hardware Installation Connecting the DVG-2101S Directly to a Modem If your computer connects directly to a DSL or Cable modem and does not connect to a router, follow the steps below to install your DVG-2101S. Note: This is the most common setup configuration for the DVG-2101S. If you do not require the use of more than one LAN port, you do not need an additional router. 1. Turn off your computer. 2. Disconnect the power to your C
Summary of the content on the page No. 9
Hardware Installation DVG-2101S User Manual Connecting the DVG-2101S Behind a Router If you wish to connect your DVG-2101S behind a router, follow the steps below. After the steps are completed, your setup should look similar to the diagram below. 1. Turn off your computer. 2. Disconnect the power to the Cable/DSL modem (unplug the modem or turn off the power switch). 3. Disconnect the power to your existing router (unplug the router or turn off the power switch). 4. Unpack
Summary of the content on the page No. 10
DVG-2101S User Manual Hardware Installation By default the unit is already configured to work behind a router. Be sure to change your computer’s IP settings to DHCP (to automatically be assigned an IP address from the DVG-2101S) regardless of what type of Internet connection you have. (Please refer to your Network Interface Card’s manual for more detailed information.) 8
Summary of the content on the page No. 11
Configuration DVG-2101S User Manual Configuration Prior to using your web browser for accessing the web-based configuration utility, if DHCP is not enabled on your computer, be sure to assign a static IP address to the VoIP Telephone Adapter. Use the computer that was last connected directly to your Cable/DSL modem. Right-click My Network Places > select Properties > right-click Local Area Connection > select Properties > double-click Internet Protocol (TCP/IP). Set your PC’s
Summary of the content on the page No. 12
DVG-2101S User Manual Configuration The Setup Wizard will guide you through the quick setup steps. Click Setup Wizard. Click Next. Step 1 You can change the login password during this step or just leave them the same as the default values. Click Next. Step 2 Select your time zone from the drop-down list. Then select a NTP time server or configure your preferred time server. Click Next. 10
Summary of the content on the page No. 13
Configuration DVG-2101S User Manual Step 3-1 If you selected Static IP, enter the IP address, subnet mask and gateway supplied by your ISP. Click Next. Step 3-1-1 Static IP users have to set the DNS address. Click Next. Step 3-1 If you selected Dynamic IP, you may enter the host name in the field. Click Next. 11
Summary of the content on the page No. 14
DVG-2101S User Manual Configuration Step 3-1 If you selected PPPoE, enter your username and password supplied by your ISP. Click Next. Step 4 Enable and configure your SIP account (phone port ) with the settings provided by your ISP/ITSP. Click Next. Step 5 Setup is finished. Click Restart to reboot the DVG-2101S. Once the adapter is finished rebooting, turn on your modem and allow up to 2 minutes to connect to your ISP. Click Restart. 12
Summary of the content on the page No. 15
Setup DVG-2101S User Manual Setup Internet Setup Connection Type The WAN connection type setting allows you to configure this device to establish your broadband Internet connection. Your Internet Service Provider (ISP) should provide the necessary information to you when you subscribe to the Internet access service. Dynamic IP Choose Dynamic IP if the VoIP Adapter obtains its WAN IP address from a DHCP server. Input the host name of the DHCP server. Host Name 13
Summary of the content on the page No. 16
DVG-2101S User Manual Setup Static IP Choose Static IP Address if the WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS addresses provided to you by your ISP. You should enter the IP address, subnet mask, and gateway address in this page and enter the DNS addresses in the DNS page which is under the Advanced tab. IP Address Input the public IP Address provided by your ISP. Subnet Input your Subnet
Summary of the content on the page No. 17
Setup DVG-2101S User Manual PPPoE Choose PPPoE (Point-to-Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. Most DSL users will select this option. PPPoE User Enter the PPPoE user name supplied by your ISP. Name PPPoE Enter the PPPoE password supplied by your ISP. Password Check Retype the password entered in the previous field. Password PPPoE Enter the PPPoE Service Name (if supplied by your ISP). Ser
Summary of the content on the page No. 18
DVG-2101S User Manual Setup MAC Address Clone Basically, every Ethernet interface (also called a NIC - Network Interface Card) has a MAC address. If the administrator assigns IP addresses to devices according to the authorized MAC address, or only allows devices with authorized MAC addresses to access the network, you may manually enter the MAC address here. MAC Address Check this checkbox to enable the MAC Address Clone feature. Clone MAC Address Enter the MAC address you wan
Summary of the content on the page No. 19
Setup DVG-2101S User Manual Static Routing You can specify additional information according to the network topology the VoIP Adapter is attached to in order to establish an efficient networking environment. Click Add button to configure static routing settings. Network Enter in the IP address of the specified network that you want to Destination access using the static route. Netmask Enter in the subnet mask for the specified network. Gateway Enter in the gateway IP address
Summary of the content on the page No. 20
DVG-2101S User Manual Setup VoIP Setup The VoIP (Voice over Internet Protocol) Adapter can be configured to handle voice communication over the Internet. The screen shown below, along with the SIP account list and phone book pages are used to configure the basic settings to allow you to communicate with the devices that will send and receive telephone calls over the Internet. SIP Account List The VoIP Adapter allows you to make calls through the Internet or PSTN. You need to conf
