Summary of the content on the page No. 1
Owner’s Manual
5.5 Horsepower
2500 PSI
2.5 GPM
PRESSURE WASHER
Model No.
919.672190
Safety Guidelines
Assembly
Operation
Maintenance
Storage
Troubleshooting
Repair Parts
CAUTION: Read the Safety Guidelines
and All Instructions Carefully Before
Operating.
Sold by Sears Canada, Inc. Toronto, Ont. M5B 2B
D30333 Rev. 0 11/03/03
Summary of the content on the page No. 2
TABLE OF CONTENTS WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SPECIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 SAFETY GUIDELINES- DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . .3 CONSUMER SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . .3 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . .3-7 BOX CONTENTS . . . . . . . . .
Summary of the content on the page No. 3
SPECIFICATION CHART Model No. 919.672190 Pressure Washer Pressure 2500 PSI Flow Rate 2.5 GPM Cleaning Units (PSI x GPM) 6250 Engine RPM 3600 Rated Horsepower 5.5 Spark Plug Gap .030” (0.76mm) Gasoline Capacity .29 gallons (1.1 liters) Oil .58 quarts ( .55 liters) capacity SAE 30 weight SAFETY GUIDELINES - DEFINITIONS This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you
Summary of the content on the page No. 4
IMPORTANT SAFETY INSTRUCTIONS Read Operators Manual. Do not operate equipment until you have read operators Manual for Safety, Assembly, Operation, and Maintenance Instructions. READ AND SAVE THESE INSTRUCTIONS HAZARD RISK OF EXPLOSION OR FIRE WHAT CAN HAPPEN HOW TO PREVENT IT Spilled gasoline and it’s vapors can be- Shut off engine and allow it to cool before come ignited from cigarette sparks, adding fuel to the tank. electrical arcing, exhaust gases, and hot Use care in filling tank to
Summary of the content on the page No. 5
HAZARD RISK OF INJURY OR PROPERTY DAMAGE WHEN TRANSPORTING OR STORING WHAT CAN HAPPEN HOW TO PREVENT IT Fuel or oil can leak or spill and could If pressure washer is equipped with a fuel result in fire or breathing hazard, serious shut-off valve, turn the valve to the off injury or death can result. Fuel or oil leaks position before transporting to avoid fuel will damage carpet, paint or other leaks. If pressure washer is not equipped surfaces in vehicles or trailers. with a fuel shut-off va
Summary of the content on the page No. 6
HAZARD RISK OF UNSAFE OPERATION WHAT CAN HAPPEN HOW TO PREVENT IT Unsafe operation of your pressure washer Do not use chlorine bleach or any other could lead to serious injury or death to corrosive compound. you or others. Become familiar with the operation and con- trols of the pressure washer. Keep operating area clear of all persons, pets, and obstacles. Do not operate the product when fatigued or under the influence of alcohol or drugs. Stay alert at all times. Never defeat the s
Summary of the content on the page No. 7
HAZARD RISK OF INJURY FROM SPRAY WHAT CAN HAPPEN HOW TO PREVENT IT Always wear ANSI approved Z87 safety High velocity fluid spray can cause glasses.Wear protective clothing to protect objects to break, propelling particles at against accidental spraying. high speed. Never point wand at, or spray people or Light or unsecured objects can become animals. hazardous projectiles. Always secure trigger lock when wand is not in service to prevent accidental operation. Never permanently secur
Summary of the content on the page No. 8
ASSEMBLY 1. Remove cleaning solution tanks 4. Attach high pressure hose to gun. from frame assembly. Slide tanks up Tighten securely. and away from frame assembly. 5. To Assemble Accessories Panel a. Remove top screws on 2. Place handle assembly onto frame handle assembly. and connect handle to frame. NOTE: Knobs are assembled to b. Loosen bottom screws on the outside of frame. handle assembly. Remove Loosen c. Place grooves in accessories panel assembly onto screws and slide panel assembly into
Summary of the content on the page No. 9
d. Place screws (removed earlier) into the top holes and secure accessories panel assembly to handles. Do not overtighten. 6. Reinstall cleaning solution tanks. Tilt cleaning solution tanks toward engine, slide onto handles, and snap into place. 7. Attach cleaning solution hose to barb fitting on control valve located at the rear of unit. barb fitting 9- ENG D30333
Summary of the content on the page No. 10
OPERATION READ THIS OPERATION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Spray Choke Gun Control High Throttle Pressure Control Hose Hand Grip Fuel Valve Air Filter Lever Dual Tank Cleaning System Engine Multi- Adjustable Spray Wand High Pressure Pump Chemical Injector Rinsing Hose (not PRESSURE WASHER shown): Rinses the chemical
Summary of the content on the page No. 11
PRESSURE WASHER TO ADJUST PRESSURE TERMINOLOGY The pressure setting is preset at the factory to achieve optimum pressure PSI: Pounds per Square Inch. The unit and cleaning. If you need to lower the of measure for water pressure. Also pressure, it can be accomplished by used for air pressure, hydraulic these methods. pressure, etc. 1. Back away from the surface to be GPM: Gallons Per Minute. The unit of cleaned. The further away you are, measure for the flow rate of water. the less the pressure
Summary of the content on the page No. 12
The nozzle at the end of the multi- 3. Fill cleaning solution tanks with desired cleaning solution. Each adjustable spray wand can be rotated tank holds approximately 1.25 to change the high pressure spray gallon. NOTE: The cleaning pattern from a narrow jet to a 40º fan solution/water ratio is 7:1, for shape, as shown. Markings have been every 7 gallons of water pumped, placed on the nozzle to help you 1 gallon of cleaning solution will select the spray pattern. be used. Never fill cleaning so
Summary of the content on the page No. 13
2. If only one cleaning solution is c. Place other end of chemical being used both tanks may be injector rinsing hose into filled with the same solution to container of clean water and double the capacity before refilling depress trigger to draw at least tanks. one gallon of clean water through chemical injection 3. If only one cleaning solution is system to rinse system being used the second tank may thoroughly. be filled with clean water to d. Before reconnecting cleaning conveniently rinse t
Summary of the content on the page No. 14
3. Turn the fuel valve to the OFF 1. In a well ventilated outdoor area position if engine will not be add fresh, high quality, unleaded restarted soon. gasoline with a pump octane rating of 86 or higher. Do not 4. Turn water source off. overfill. Wipe up spilled fuel before 5. Pull trigger on spray gun to relieve starting the engine. any water pressure in hose or 2. Remove filler cap/dipstick and spray gun. add engine oil (supplied) to 6. See Storage section in this engine. NOTE: There will
Summary of the content on the page No. 15
6. If applying a cleaning solution, see If the engine does How To Use the Dual Cleaning not start after two Solution System in Operation pulls, pull the trigger to relieve the section of this manual. pressure. 7. Turn water source on. 11. If the choke was used to start the NOTE: Failure to do so could cause engine, move the choke lever to damage to the pump. the OFF position. 8. Turn fuel valve to the ON position, 12. Depress trigger on gun to start 1/4 turn counterclockwise. water flow. NOTE:
Summary of the content on the page No. 16
CUSTOMER RESPONSIBILITIES TABLE Every 25 Every 50 Every 100 Before hours or hours or hours or each use MAINTENANCE TASK yearly yearly yearly ENGINE X check oil level change oil X check air filter X clean/replace spark plug X PRESSURE WASHER check/clean inlet screen X check high pressure hose X check soap and chemical X hose and filter check gun and wand for leaks X Prepare unit for storage if it is to remain idle for longer prepare for storage than 30 days ENGINE Oil Filler To Check Oil Cap/Dip
Summary of the content on the page No. 17
To Change Oil Air Cleaner Drain the engine oil when the engine is A dirty air cleaner will restrict air flow to warm. Warm oil drains quickly and the carburetor and cause poor engine completely. performance. Inspect the filter each time the engine is operated. Clean the 1. Turn the fuel valve to the OFF position, 1/4 turn clockwise. filter more frequently if the engine is 2. Place a suitable container next to operated in very dusty areas. the engine to catch the used oil. NOTICE: Operating the e
Summary of the content on the page No. 18
Clean and Replace Spark Plug 3. Pull trigger on gun handle to relieve any water pressure. Change the spark plug every 100 hours of operation or once each year, 4. Disconnect the wand from the gun. whichever comes first. This will help your engine to start easier and run 5. Remove the nozzle from the end better. of the wand with the 2mm allen wrench provided as shown. .030” (0.76 MM) Wire Gauge 6. Clean the nozzle using the nozzle Resistor cleaner provided or a straightened paper clip. Insert in
Summary of the content on the page No. 19
STORAGE ENGINE PUMP 1. Drain all water from high IMPORTANT: It is important to prevent pressure hose, coil it, and store it gum deposits from forming in essential in cradle of the pressure washer fuel system parts such as the handle. carburetor, fuel filter, hose or tank during storage. Also, experience 2. Drain all water from spray gun indicates that alcohol-blended fuels and spray wand by holding spray (called gasohol or using ethanol or gun in a vertical position with methanol) can attract mo
Summary of the content on the page No. 20
7. Add *RV antifreeze to hose as shown. 8. Pull engine starter rope slowly several times until antifreeze comes out of high pressure hose connection of pump. 9. Remove short hose from water inlet of pump. 4. Turn control valve toward tank to 10. Reconnect spark plug wire. be drained. * Windshield washer fluid may also be 5. Repeat steps 3-4 to drain second used tank. 6. Turn control valve knob to the DUAL TANK CLEANING down (off) position. SYSTEM 7. Fill tanks with clean water. 1. Turn control v
