Summary of the content on the page No. 1
Model PSI GPM HP
CS1000.22 1000 2.2 1.5
CS1300.22 1300 2.2 2.0
Operator’s Manual
Summary of the content on the page No. 2
Thank you Thank you for selecting our products. Our personnel have proudly made every effort to ensure that your new pres- sure washer is of the quality you expect. But things do occasionally go wrong. This is why every pressure washer is covered by a limited warranty. Among other things, this warranty provides for the replacement of parts found to be defective during the operation of your new pressure washer. Please note that the owner/operator has cer- tain obligations under the terms of the w
Summary of the content on the page No. 3
WARNING The following warnings must be followed, Failure to follow these warnings could result in serious personal injury or death! Never allow children or untrained personnel to operate machinery. Electrical equipment can cause shock and sparks. Do not bypass or remove the grounding prong in any electrical plug. Keep electri- cal plugs, connections and cords out of water and moisture. Refer to instructions prior to equipment operation. Disconnect from power source before servicing. Inspect and
Summary of the content on the page No. 4
Initial setup and operation of your new jetter/pressure washer Inspection When you receive your pressure washer, be sure you check for concealed freight damage. Any for freight damage should be noted with the delivering carrier. If you have any questions related to freight, damage call the 800 number listed on the inside front cover of the manual. Check all oil levels in the pump or engine, if applicable. Failure to check all levels will result in Inspection of oil levels equipment damage. Most
Summary of the content on the page No. 5
During operation The pressure was set at the factory during the testing procedure; no adjustments to the machine should be required for operation. During operation, do not leave the machine running for more than two minutes without the trigger gun being pulled. Although your machine has a by-pass valve on it and may have a thermal relief system, this pressure build-up can cause extensive pump damage. If machine will not be discharging water for more than two minutes, shut the machine off. Access
Summary of the content on the page No. 6
Shut-down procedure Shut-down 1. Turn off the power switch on the pressure washer. 2. Relieve pressure on line by pulling trigger gun. 3. Shut off water supply and disconnect garden hose. 4. Be sure to check for water leaks or oil leaks that should be repaired before the next oper- ation. Storage 5. If you are going to store the machine for extended periods of time in cold climates be sure to anti-freeze the equipment. A 50% anti-freeze solution may be drawn in through the inlet of the pump usin
Summary of the content on the page No. 7
Troubleshooting Despite the complexity of your jetter, a number of common complaints stem from relatively simple problems. With guidance, the user can identify and remedy many common problems. Always disconnect the power supply before attempting to service any equipment. Common problems and solutions Malfunction Cause Remedy U Un niit t r ru un ns s b bu ut t n no o w wa at te er r d diis s- -Water supply not turned on -Turn on water supply c ch ha ar rg ge es s -Plugged nozzle on discharge -Rem
Summary of the content on the page No. 8
Hose 3/16 x 100’ Reel Asly 519033H Coupler fittings 526496.6 527810 F x F Hose, Leader 525116 527715 Mx F 509096 Ball Valve Pump TT9061EFUI Thermal Valve 509312 Tip, Laser Bracket, Reel Valve, Pulse LAS18-CS1300.2 526569.1 Wheel 10x 4 GEN100315 LAS18-CS1000.2 524566 Swivel 526493 Handle 510411T.2D Motor Lynch pin 521350 (1.5hp) 526521 521308.1 (2hp) 524100 Switch Rubber foot 526305 510411T.B Base, Cart
Summary of the content on the page No. 9
EDP # DESCRIPTION LIST HIGH PRESSURE CHEMICAL INJECTOR The stainless steel construction makes this nozzle suitable for various soaps, sanitizers, fungicides and chemical cleaning solutions. Nozzle barrel propels a concentrated spray pattern up to 25-35 feet. Stainless steel construction provides high strength and chemical resistance. Adjustment knob at nozzle body allows for convenient chemical metering. 30’ of chemical hose and a check valve which prevents reversal of solution back to the
