Summary of the content on the page No. 1
❉ ❉ ❉ ❉ ❉ ❉
❉ ❉
❉
❉ ❉
❉ ❉
❉
❉ ❉ ❉ ❉
❉ ❉
❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉
GB STL 60 PROGRAMME CHART
A. Temperature Selection Knob
B. “On/Off” Button
C. “Spin Speed Reduction” Button
: option / Yes: dosing required
1)
Do not use liquid detergents.
2)
A C B For improved garment care, spin speed is zero in this
programme.
Max. Detergents and additives Special Options Tempera- Max.
load ture Spin
Prewash Main Softener Bleach Rinse Intensive Half Spin Speed
Care Speed
Wash Hold Rinse Load Reduction
Programme
Summary of the content on the page No. 2
“Intensive Rinse” button CHANGE THE PROGRAMME DURING THE CONSUMPTION DATA One rinse cycle is added to ensure a more WASH CYCLE Temperature Selector Load Water Energy Approx. Programme intensive rinse. 1. Switch off the machine by pressing the Duration Programme This option is particularly suitable for areas with “On/Off” button. (°C) (kg) (l) (kWh) (hours : minutes) very soft water, washing baby linen and people 2. Select the new programme. Cotton 95 5.0 63* 1.80 2:05 with detergents al
Summary of the content on the page No. 3
IFU_Alpha_Sc1-mech_GB.fm Page 1 Wednesday, March 30, 2005 6:52 PM CONTENTS BEFORE USING THE WASHING MACHINE FIRST WASH CYCLE PRECAUTIONS AND GENERAL RECOMMENDATIONS DESCRIPTION OF THE WASHING MACHINE PREPARATION OF THE WASHING DETERGENTS AND ADDITIVES PROGRAMME SELECTION CLEANING THE FOREIGN BODY TRAP DRAINING RESIDUAL WATER CARE AND MAINTENANCE TROUBLESHOOTING GUIDE AFTER-SALES SERVICE TRANSPORT AND HANDLING INSTALLATION ELECTRICAL CONNECTION Black process 45.0° 100.0 LPI
Summary of the content on the page No. 4
IFU_Alpha_Sc1-mech_GB.fm Page 2 Wednesday, March 30, 2005 6:52 PM BEFORE USING THE WASHING MACHINE 1.Remove the packaging and check 6.Electrical connection Electrical connections must be carried out by a a. Cut and remove the shrink-wrap. qualified technician in compliance with the b.Remove the top protection and the protective corners. manufacturer’s instructions and the current c. Remove the bottom protection by tilting and standard safety regulations. turning the washing machine on o
Summary of the content on the page No. 5
IFU_Alpha_Sc1-mech_GB.fm Page 3 Wednesday, March 30, 2005 6:52 PM FIRST WASH CYCLE We recommend that the first wash cycle be carried out empty. This will remove any residual water used in the factory checks. 1. Turn on the tap. 2. Close the drum flaps. 3. Pour a small amount of detergent (about 30 ml) into the detergent dispenser . 4. Select a short programme (see programme chart). 5. Switch on the machine by pressing the “On/Off” button. PRECAUTIONS AND GENERAL RECOMMENDATIONS 1.Packing to
Summary of the content on the page No. 6
IFU_Alpha_Sc1-mech_GB.fm Page 4 Wednesday, March 30, 2005 6:52 PM DESCRIPTION OF THE WASHING MACHINE 1 1. Lid 2. Detergent dispenser 3.Drum flaps 2 4. Pump and foreign body trap 5. After-Sales Service sticker (behind 3 the foreign body trap cover) 6. Mobility lever (depending on model) To move the washing machine: pull the handle out a little bit by hand and pull it out to the stop with the foot. 7. Adjustable feet 4 6 5 7 PREPARATION OF THE WASHING Sort the laundry Stain removal Bloo
Summary of the content on the page No. 7
IFU_Alpha_Sc1-mech_GB.fm Page 5 Wednesday, March 30, 2005 6:52 PM Loading the laundry 1. Open the machine lid. 2.Open the drum by pressing the small flap (2a) or the push button (2b) - depending on model - and holding the large flap. For the drum opening shown on 2c, you just have to press the push button, without holding the 1 large flap. 3. Place the items of laundry in the drum one by one without compressing them. Follow loads recommended in the “programme chart”: overloading will r
Summary of the content on the page No. 8
IFU_Alpha_Sc1-mech_GB.fm Page 6 Wednesday, March 30, 2005 6:52 PM DETERGENTS AND ADDITIVES Choice of the right detergents and additives Dosage Follow the instructions on the detergent pack in The type of detergent depends on: relation to: type of fabric (cottons, easy care/synthetics, delicate items, wool). the degree and type of soiling; Note: use only specific detergents for wool. the size of the load; colour; - full load: follow the detergent manufacturer’s instructions; washi
Summary of the content on the page No. 9
IFU_Alpha_Sc1-mech_GB.fm Page 7 Wednesday, March 30, 2005 6:52 PM PROGRAMME SELECTION Preparation of wash cycle 1. Load the machine, close the drum flaps and check that they are properly locked. 2. Add detergents and additives into the dispenser to no more than the “MAX” level mark. Please refer to “Detergents and additives”. 3. Turn the programme selector knob to the desired programme. 4. Turn the temperature selector knob (if available) to the desired temperature. 5. Turn the spin speed s
Summary of the content on the page No. 10
IFU_Alpha_Sc1-mech_GB.fm Page 8 Wednesday, March 30, 2005 6:52 PM CLEANING THE FOREIGN BODY TRAP The washing machine is provided with a self-cleaning pump. The foreign body trap keeps objects like buttons, coins, safety-pins etc. which have been left in the laundry. 1. Unplug the washing machine. 2. Open the foreign body trap cover with a coin. 3. Place a bowl beneath it. 4. Turn the foreign body trap slowly anti-clockwise until the grip is vertical; do not remove it as yet. 5. Wait until
Summary of the content on the page No. 11
IFU_Alpha_Sc1-mech_GB.fm Page 9 Wednesday, March 30, 2005 6:52 PM DRAINING RESIDUAL WATER When should I drain residual water (draining problem)? Before transporting (moving) the machine. If the washing machine is installed in a room subject to sub- zero temperatures. It is best in this case to drain the machine after every wash. 1. Stop the washing machine and unplug it. 2. Turn off the tap, disconnect the water supply hose from the machine and allow the water to drain into a basin. 3.
Summary of the content on the page No. 12
IFU_Alpha_Sc1-mech_GB.fm Page 10 Wednesday, March 30, 2005 6:52 PM Water inlet hose filter Check and clean regularly (at least two or three times a year). 1. Unplug the washing machine. 2. Turn off the tap. 3. Unscrew the hose from the tap. 4. Carefully clean the filter located at the end of hose, without assembling it, for example with a tooth-brush. Note: For machines equipped with hose type “A”, it must not be submerged in water. 5. Screw the flexible hose back onto the tap by hand. Do
Summary of the content on the page No. 13
IFU_Alpha_Sc1-mech_GB.fm Page 11 Wednesday, March 30, 2005 6:52 PM Washing machine exterior and control panel Lid seal Clean with a soft damp cloth. Clean from time to time with a damp cloth. If necessary, a neutral household cleaner can be Water inlet hose(s) applied (do not use aggressive or abrasive Check the hose regularly for brittleness and products). cracks. Replace if necessary. TROUBLESHOOTING GUIDE This washing machine is equipped with automatic Reconnect the washing machi
Summary of the content on the page No. 14
IFU_Alpha_Sc1-mech_GB.fm Page 12 Wednesday, March 30, 2005 6:52 PM *Final spin results are poor. Water stop fault (depending on model). Note: the washing machine has an unbalance (The pump operates). detection and correction system. If individual heavy The “Water Stop” fault may have been items are loaded (a bathrobe, for example), this triggered by: system may reduce the spin speed automatically or Too much foam. interrupt the spin if it detects too great unbalance at A leak in the
Summary of the content on the page No. 15
IFU_Alpha_Sc1-mech_GB.fm Page 13 Wednesday, March 30, 2005 6:52 PM AFTER-SALES SERVICE Before contacting After-Sales Service: Specify: 1. Try to remedy the problem yourself (see The nature of the problem. “Troubleshooting Guide”). The exact model of the washing machine. 2.Restart the programme to check whether the The service code (number after the word problem has solved itself. SERVICE). 3. If the machine continues to function incorrectly, call After-Sales Service. The After-Sales
Summary of the content on the page No. 16
IFU_Alpha_Sc1-mech_GB.fm Page 14 Wednesday, March 30, 2005 6:52 PM INSTALLATION Removal of transport bracket The washing machine is fitted with a transport bracket to avoid any possible damage during transport. A B Before using the washing machine, the transport bracket at the back MUST be removed. 1. Unscrew the two screws A and the four screws B with a D flat screwdriver or a No. 8 hex nut box spanner. 1 2. Remove the transport bracket. 3. Replace the four outer screws B on the machine a
Summary of the content on the page No. 17
IFU_Alpha_Sc1-mech_GB.fm Page 15 Wednesday, March 30, 2005 6:52 PM Adjust the feet Install the washing machine on a level surface, near to electrical, water and drain connections. If the floor is uneven, adjust the feet (do not insert pieces of wood, cardboard etc. under the feet): 1.Loosen the locknut using the wrench provided. 2. Adjust the height of the foot by hand. 3. Retighten the locknut by turning it anti-clockwise. Make sure that all feet are resting correctly on the floor and tha
Summary of the content on the page No. 18
IFU_Alpha_Sc1-mech_GB.fm Page 16 Wednesday, March 30, 2005 6:52 PM Water stop anti-flooding system (depending on model) Screw the hose to the water supply tap. Turn the tap fully on and check the water-tightness of the connection. The washing machine must not be connected to the mixing tap of a non-pressurized water heater! The inlet hose and the plastic enclosure contain (depending on model) electrical components: do not cut the hose and do not immerse the enclosure in water. If
Summary of the content on the page No. 19
IFU_Alpha_Sc1-mech_GB.fm Page 17 Wednesday, March 30, 2005 6:52 PM ELECTRICAL CONNECTION Do not use extension leads or multi sockets. Electrical connections must be made in accordance with local regulations. 1) Warning - this appliance must be earthed This appliance is normally supplied with a mains lead having a plug fitted in the factory which has been checked for correct earth continuity. If the fitted plug is not suitable for your socket outlet, or if the machine’s mains lead is not
