Summary of the content on the page No. 1
thermaline S90
GAS FRYERS - FRITEUSE POUR GAZ
Doc.
62.9679.01_UL
Edition 1
01.2006
US INSTALLATION- AND OPERATING INSTRUCTIONS page 3
FR INSTRUCTIONS D’INSTALLATION ET D’EMPLOI page 13
FOR YOUR SAFETY POUR VOTRE SÉCURITÉ
Do not store or use gasoline or Ne déposez pas ou n'employez
other flammable vapors or liquids pas l'essence ou d'autres vapeurs
in the vicinity of this or any other ou liquides inflammables à pro-
appliance. ximité de ceci ou d'aucun autre
appareil.
WARNING AVERTISSEMENT
I
Summary of the content on the page No. 2
Against wall - contre une paroi Free standing - isolé Connections - Raccordement Gas - Gaz Fig.1 INSTALLATION DRAWINGS - PLANS D'INSTALLATION Doc. 62.9679.01_UL
Summary of the content on the page No. 3
CONTENTS I. GENERAL INFORMATION .................................................................................................3 II. INSTALLATION INSTRUCTIONS .......................................................................................5 III. OPERATING INSTRUCTIONS ............................................................................................9 SOMMAIRE IV. INSTRUCTIONS GÉNÉRALES .........................................................................................13
Summary of the content on the page No. 4
Page 2 62.9679.01_UL
Summary of the content on the page No. 5
GENERAL INFORMATION I . GENERAL INFORMATION 1. INSTRUCTIONS FOR SAFETY AND USE 1.4 SAFETY-CONSCIOUS WORKING 1.1 INSTALLATION AND INITIAL OPERATION The trough heating must not be switched on if there is no oil in the trough or the oil level The installation, adjustment and initial opera- has fallen below the minimum. - Risk of fire. tion of the appliance must be carried out Food must be placed slowly in the heated according to the manufacturer's instructions trough, to prevent the oil fro
Summary of the content on the page No. 6
GENERAL INFORMATION 1.5 AFTER-SALES SERVICE AND REPAIR 2. TECHNICAL DATA Width Trough Power In the event of a permanent fault which inter- PNC Appliances Appliance type Depth contents Gas feres with operation, the appliance must be Height consumption switched off and disconnected from the inch mm power supply. 9CHG584101 WFGROFOOOO 19.7 500 6.1 gal 22 kW 35.4 900 To perform maintenance and repairs contact 1 x 23 l 75000 BTU 9CHG584102 WFGROAOOOO 35.4 900 the factory, the factory representat
Summary of the content on the page No. 7
INSTALLATION INSTRUCTIONS II . INSTALLATION INSTRUCTIONS 1. INSTALLATION 1.3 ASSEMBLING TWO APPLIANCES The appliance is designed for connection to fixed lines. The appliances are suitable for setting up as single appliances or as a group of appliances. They can be set up freely in the room, side by side, at the side and/or at the back against a wall. (3a) Gaps between two appliances or appliance and sidewall should be filled with a FDA approved silicone such as Samco (1) (2) RTV103. (3b) 1
Summary of the content on the page No. 8
INSTALLATION INSTRUCTIONS 1.4 SIDEWALL (D) 1.6 ASSEMBLING ON CASTORS () (5) (4) () (5) (4) 1 1 (3c) 1 a a b Fig.2 Assemblage of sidewall The assembly kit contains two of each of the following: (3c) hexagonal screws M8x25 (1 / Fig.1), bolts with retaining rings 1 (3c) 1 (2 / Fig.1), mounting links (3 / Fig.1), hexagonal screws M8x16 with serrated washers and hexagonal nuts M8, hexagonal c screws M5 with serrated washers (4 / Fig.2) b and a fastening angle (5 / Fig.2). Fig.4 Assemblage on ca
Summary of the content on the page No. 9
INSTALLATION INSTRUCTIONS 2.1 FRONT PANELS (A) and (B) (1) Fig.6 Front panel Unscrew screws (1 or 3). Also, in the case of a built-in oven, unscrew screws (2 and/or 4) on the inside of the oven. Pull the panel away forwards and downwards. 2.2 CONTROL PANEL (C) (2) (3c) (3c) (1) 1 1 ab (3) Fig. 7 Control panel c Remove the knob. Loosen the screws underneath (1 / Fig.7a) and remove the base plate. Loosen the screws (2 / Fig.7b) and 3 / Fig.7c) Remove the panel. 2.3 OVEN, STORAGE SPACE, HOT
Summary of the content on the page No. 10
INSTALLATION INSTRUCTIONS 3. GAS CONNECTION Retighten the slotted screw in the measuring nipple. Gas pressure deviation tolerances are laid down by EN 203. If The installation of the gas connection, as well as the laying of the existing gas pressure is outside the given tolerances, the customer's gas line, is only to be carried out by an author- correct combustion can no longer be ensured. Compulsory ised specialist subject to the relevant national and local regula- measures: pressure adjustmen
Summary of the content on the page No. 11
OPERATING INSTRUCTIONS III . OPERATING INSTRUCTIONS 2.3 TEMPERATURE SELECTION 1. GENERAL With the knob (1/Fig.8) the temperature can be steplessly The appliance is used for deep frying. In operation the basket adjusted between 230 and 360°F (110 and 180°C). is suspended. The oil bath working temperature is adjustable. An additional safety thermostat (STB) prevents unacceptably high tempera- 2.4 OPERATION tures from being reached. In the case of appliances with two troughs, these can be used 2.4.
Summary of the content on the page No. 12
OPERATING INSTRUCTIONS 3.2 SWITCHING OFF THE OVEN Wash rust-resistant chrome nickel steel panels with hot soapy water to which a fat-dissolving agent has been 3.2.1 MAIN BURNER added and rub them dry. Turn the knob (1/Fig.9) back clockwise from highest setting Note 7 to pilot burner ignition 1. The appliance must not be sprayed with a water jet or high- The gas supply to the main burner is stopped and the main pressure cleaner. flame is shut down. The flame of the pilot burner keeps on
Summary of the content on the page No. 13
OPERATING INSTRUCTIONS 8. MALFUNCTION Malfunction Possible cause Remedy Fryer does not heat up. • The STB limiter has - Contact the nearest tripped. service station by tele- phone. • Defective thermostat. - Inform After-sales ser- • vice. • The oil temperature - Inform After-sales ser- has exceeded 445°F vice. (230°C). - Inform After-sales ser- • The capillary tube sen- vice. sor is damaged. - Pour in oil. • The heating is opera- ting in the trough wit- - hout oil. - Top up with oil. • Oil lev
Summary of the content on the page No. 14
OPERATING INSTRUCTIONS Seite 12 62.9679.01_UL
Summary of the content on the page No. 15
INSTRUCTIONS GÉNÉRALES I . INSTRUCTIONS GÉNÉRALES 1. CONSIGNES DE SÉCURITÉ ET D'UTILISATION 1.4 TRAVAILLER EN TOUTE SÉCURITÉ 1.1 INSTALLATION ET MISE EN SERVICE N'activez jamais la résistance de la cuve lorsque celle-ci ne contient pas d'huile ou Le montage, le réglage et la première mise lorsque que le niveau d'huile à travers le en service de l'appareil doivent s'effectuer regard se situe en deçà du repère mini- conformément aux instructions du fabricant mum. - Risque d'incendie. et ê
Summary of the content on the page No. 16
INSTRUCTIONS GÉNÉRALES 1.5 SERVICE-APRÈS-VENTE ET RÉPARATION 2. DONNÉES TECHNIQUES Largeur Contenu Puissance Si un problème persistant empêche le Profondeur de la Consommation Modèle Appareil PNC fonctionnement correct de l'appareil, mettez- Haute cuve de gaz de l'appareil le hors tension et débranchez-le. inch mm Pour toute opération d'entretien ou de répa- 9CHG584101 WFGROFOOOO 19.7 500 6.1 gal 22 kW 35.4 900 ration, adressez-vous au fabricant, à un 1 x 23 l 75000 BTU 9CHG584102 WFGROAOOO
Summary of the content on the page No. 17
INSTRUCTIONS RELATIVES À L'INSTALLATION II . INSTRUCTIONS RELATIVES À L'INSTALLATION 1. MISE EN PLACE 1.3 ASSEMBLAGE DE DEUX APPAREILS Cet appareil est conçu pour être raccordé à des conduites fixes. Les appareils peuvent être montés individuellement ou en groupe. Ils peuvent être installés de façon indépendante, côte à côte, avec un côté et/ou la partie arrière de l'appareil (3a) reposant contre une paroi. Les interstices entre deux appareils ou entre un appareil et le (1) (2) mur latéral
Summary of the content on the page No. 18
INSTRUCTIONS RELATIVES À L'INSTALLATION 1.4 PAROI LATERALE (D) 1.6 ASSEMBLAGE SUR ROULETTES () (5) (4) () (5) (4) 1 1 (3c) 1 a a b Fig.2 Montage du paroi latérale Chaque kit d'assemblage comprend respectivement deux vis hexagonales M8 x 25 (1 / Fig.1), des boulons avec circlip (2 (3c) 1 (3c) / Fig.1), des éclisses (3 / Fig.1), des vis hexagonales M8 x 16 1 avec rondelles à denture intérieure et des vis hexagonales M8, des vis hexagonales M5 avec rondelles à denture intérieure (4 c b / Fig.1)
Summary of the content on the page No. 19
INSTRUCTIONS RELATIVES À L'INSTALLATION 2.1 PANNEAU AVANT (A) et (B) (1) Fig.6 Frontblenden Desserrez les vis (1 et 3 Fig.5, Fig.6). Si le four est encastré, desserrez Extrayez le panneau vers l'avant et le bas. 2.2 PANNEAU DE COMMANDE (C) (2) (3c) (3c) (1) 1 1 ab (3) Fig.7 Panneau de commande c Enlever l'interrupteur rotatif. Dévissez les vis placées au-dessous (1 / fig. 7a) et enlevez la plaque support. Dévissez les vis (2 / fig. 7b) et 3 / fig. 7c) Enlevez le panneau de commande. 2.3
Summary of the content on the page No. 20
INSTRUCTIONS RELATIVES À L'INSTALLATION 3. RACCORDEMENT AU GAZ Resserrer la vis à fente dans la prise de mesure. Les écarts de tolérance de la pression de gaz sont stipulés Le raccordement au gaz, de même que la pose de la conduite dans l'EN 203. Si la pression de gaz existante dépasse les d'arrivée de gaz doivent être réalisés exclusivement par un tolérances prescrites, une combustion correcte ne peu plus spécialiste agréé, dans le respect des dispositions nationales être garantie. Mesures obl
