Summary of the content on the page No. 1
IMI CORNELIUS INC
www.Cornelius.com
Owner / Operator Use and Care Guide
“I” SERIES 224 ICE CUBE MACHINE
THE HOTTEST MACHINES ON ICE
IMPORTANT:
TO THE INSTALLER.
It is the responsibility of
the Installer to ensure that
the water supply to the
dispensing equipment is
provided with protection
against backflow by an air
gap as defined in
ANSI/ASME A112.1.2-1979;
or an approved vacuum
breaker or other such
method as proved effective
by test.
Water pipe connections
and fixtures directly
connected to
Summary of the content on the page No. 2
Summary of the content on the page No. 3
TABLE OF CONTENTS Page SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 RECOGNIZE SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 UNDERSTAND SIGNAL WORDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 FOLLOW SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 CO2 (CARBON DIOXIDE) WARNING . . . . . . . . . .
Summary of the content on the page No. 4
ii 630460069OPR
Summary of the content on the page No. 5
SAFETY INFORMATION Recognize Safety Information This is the safety-alert symbol. When you see this symbol on our machine or in this manual, be alert to the potentially of personal injury. Follow recommended precautions and safe operating practices. Understand Signal Words A signal word - DANGER, WARNING, OR CAUTION DANGER is used with the safety-alert symbol. DANGER identi- fies the most serious hazards. Safety signs with signal word DANGER or WARNING WARNING are typically near specific hazards.
Summary of the content on the page No. 6
GENERAL DESCRIPTION This section gives the Unit description, theory of operation, and design data for IMPORTANT: To the user of this manual – This manual is a guide for installing, operating, and main- taining this equipment. Refer to the Table of Contents for page location for detailed information per- taining to questions that arise during installation, operation, service, or maintenance of this equip- ment. MODEL AND SERIAL LOCATION “I” Series Cuber MODEL/SERIAL NAMEPLATE LOCATION Record the
Summary of the content on the page No. 7
WARRANTY IMI Cornelius Inc. warrants that all equipment and parts are free from defects in material and workmanship un- der normal use and service. For a copy of the warranty applicable to your Cornelius product, in your country, please write, fax or telephone the IMI Cornelius office nearest you (www.cornelius.com). Please provide the equipment model number, serial number and the date of purchase. WARRANTY COVERAGE The following warranty outline is provided for your convenience. For full detail
Summary of the content on the page No. 8
OWNER’S RECOMMENDED MAINTENANCE SEMI–ANNUAL MAINTENANCE 1. GENERAL ICE MACHINE INSPECTION 2. CLEANING THE EXTERIOR 3. CLEANING THE CONDENSER–AIR – COOLED 4. INTERIOR CLEANING–CLEANING PROCEDURES, SANITIZING PROCUDURES General Ice Machine Inspection 1. Check all water fittings and tubes for leaks. Also, make sure the refrigeration tubing is not rubbing or vibrat- ing against other tubing panels, etc. 2. Do not stack anything ( boxes, etc.) on or around the ice machine. 3. Do not cover the ice mac
Summary of the content on the page No. 9
1. Clean the outside of the condenser with a soft brush or vacuum with a brush attachment. Brush or wash condenser from top to bottom not from side to side. Be careful not to bend the fins. Shine a flashlight through the condenser to check for dirt between the fins. 2. If further cleaning is required, blow compressed air through the condenser from the inside. Take care not to bend the fan blades. Shine flashlight through the condenser to check that all the dirt is removed. IMPORTANT: Any be
Summary of the content on the page No. 10
Cleaning the Water System & Evaporator 1. Set the switch to CLEAN and allow the ice on the evaporator to POWER release and melt away. SWITCH 2. Remove all ice from the storage bin. 3. Add 3 oz. for a single evaporator of “Calgon Nickel–Safe” ice machine cleaner directly into the water pan. Set switch to CLEAN, circulate for a maximum of 15 minutes. ON 4. Depress and hold the dump switch to allow the cleaner to drain OFF CLEAN away. DUMP 5. Fill the water pan with fresh water, circulate for app
Summary of the content on the page No. 11
TROUBLESHOOTING IMPORTANT: Only qualified personnel should service internal components or electrical wiring. WARNING: If repairs are to be made to a product system, remove quick disconnects from the applicable product tank, then relieve the system pressure before proceeding. If repairs are to be made to the CO system, stop dispensing, shut off the CO supply, then relieve the 2 2 system pressure before proceeding. If repairs are to be made to the refrigeration system, make sure electrical powe
Summary of the content on the page No. 12
SAFETY LIMIT FEATURE In addition to standard safety controls such as the high pressure cut–out, your ice machine features built–in safety limits that stop the ice machine if conditions exist that may result in a major component failure. NOTE: Before calling for service, restart the ice machine using the following procedures: 1. Turn power switch off and then back to ICE MAKING ( ON ) position. If the safety limit feature has stopped the ice machine, it will restart after a short delay. Proceed t
Summary of the content on the page No. 13
Summary of the content on the page No. 14
IMI CORNELIUS INC. www.cornelius.com
