Summary of the content on the page No. 1
TABLE OF CONTENTS
WT-8029U
RADIO-CONTROLLED SOLAR CLOCK
Topic Page
Features 3
INSTRUCTION MANUAL
Battery Installation 3
Setting Up 5
Atomic time - WWVB Radio Controlled Time 5
Function keys 6
Contents
LCD Screen 7
Manual Settings 7
Languages Page
Alarm setting and snooze 11
__________________________________________
Mounting 12
Care and maintenance 14
Specifications 15
English 2
Warranty 16
French 18
FEATURES:
RADIO-CONTROLLED SOLAR CLOCK:
Spanish 36
Summary of the content on the page No. 2
WWVB Radio controlled time with manual time setting TO INSTALL / REPLACE BATTERY Time display: hour, minute, second The included alkaline rechargeable battery should provide you with many years of service. If your battery needs to be 12/24h time format display replaced, we suggest you use a fully charged AA Alkaline. Alarm setting with snooze function Calendar display Rechargeable batteries should be fully charged before inserting Weekday display (4 languages to choose fro
Summary of the content on the page No. 3
Use switch to 2. Next the WWVB time code reception will automatically select which start. This reception typically takes 10 minutes in good type of battery conditions. If after 10 minutes the WWVB time has not will be used been received, use the “SET” key to enter the set-up before Battery mode to manually set the Time, Time Zone and Date inserting the compartment (see manual settings below). The clock will continue to battery into cover search for WWVB each hour between
Summary of the content on the page No. 4
If the tower icon flashes, but does not set the time or the briefly before displaying the information for time, date, indoor WWVB tower does not appear at all, then please take note of temperature and indoor humidity. the following: Radio reception icon Recommended distance to any interfering sources like computer monitors or TV sets is a minimum of 6 feet (2 Alarm icon meters). WWVB Low battery Within ferro-concrete rooms (basements, time icon (clock) superstructures),
Summary of the content on the page No. 5
Note: the time will be displayed with an additional “PM” for the TIME ZONE time from 12:00 noon until 11:59. The time zone can be set between the +/–12 hour range in LCD2. To do this: Note: The unit will still try to receive the signal every day despite it being manually set. When it does receive the signal, it 1. The time zone (LCD2) will start flashing (Default setting will change the manually set time into the received time. During "EST -5“). Select the desired time zone by press
Summary of the content on the page No. 6
MONTH SOLAR MODE 1. The month digit on LCD2 will start flashing (Default The Solar Mode is used for saving the power consumption of setting 1). Set the desired month by use of the + key. the rechargeable battery (Default setting ON): 2. Press and release the SET key to move to the mode 1. The characters “ON” or “OFF” will start flashing on “Date Setting”. LCD1. By use of the + key select “ON” or “OFF” to set the solar mode. DATE 2. Press and release the SET key to exit the setting m
Summary of the content on the page No. 7
5. Press and release again the ALM key to exit the Alarm FOLDABLE TABLE STANDS setting mode or wait for 15 seconds automatic timeout. The foldable table stands legs are located on TO DEACTIVATE THE ALARM: the backside. Unfold the stands out, below the battery compartment. Once the foldout table stands are extended, place the radio- Alarm icon ((( ))) (ON) controlled solar clock in an appropriate location. WALL MOUNTING 1. Install a mounting screw (not inc
Summary of the content on the page No. 8
3) Be sure the radio-controlled clock is at Avoid areas where the unit can be exposed to sudden least 6 feet (2 meters) from any changes in temperature, i.e. direct sunlight, extreme cold electrical devices, i.e. TV sets, and wet/moist conditions as these will lead to rapid computers, or other radio controlled changes which reduce the accuracy of readings. clocks. When cleaning the LCD and casing, use a soft damp 4) Remove batteries for five minutes, cloth only. Do not use solvents or
Summary of the content on the page No. 9
from the performance of repairs or alterations by someone other than Low battery indicator: an authorized La Crosse Technology, Ltd authorized service center; RX - Low battery indicator is displayed on the LCD when the (6) units used for other than home use (7) applications and uses that this product was not intended or (8) the products inability to receive a battery voltage is low. signal due to any source of interference. This warranty covers only actual defects within the product
