Summary of the content on the page No. 1
6 IN 1 AIR FRAMING NAILER
97510
93910
SET UP AND OPERATING INSTRUCTIONS
®
Distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
© ®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form
Summary of the content on the page No. 2
SPECIFICATIONS Air Inlet 1/4” NPT Recommended Air Pressure 70-125 PSI* Maximum Air Pressure 125 PSI Nail Type Approx. 10 Gauge (0.113 & 0.131” Dia.) Clipped or Full Head Nails 2 - 3-1/2” Length Safety Feature Full Sequential Actuation Magazine Capacity 21° - 60 Qty., 28° and 34° - 100 Qty. Air Consumption 8-12 CFM @ 90 PSI * The air pressure setting must not exceed job site regulations/restrictions. The air pressure setting must not exceed 90 PSI when being used with work pieces that h
Summary of the content on the page No. 3
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically nonconductive clothes and nonskid footwear are recom- mended when working. Wear restrictive hair covering to contain long hair. 7. Wear ANSI-approved impact safety goggles. Wear a NIOSH-approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. Other people in the work area must also wear ANSI-approved impact safety goggles. 8. Do
Summary of the content on the page No. 4
19. Maintenance. For your safety, maintenance should be performed regularly by a qualified technician. 20. Compressed air only. Never use combustible gas as a power source. 21. Do not load nails with the trigger or safety depressed. Unintentional firing may occur. Do not load nails when the air hose is connected to the tool. Always assume that the tool contains fasteners. 22. Fire fasteners into an appropriate work surface only. Do not attempt to fire fasten- ers into surfaces too hard
Summary of the content on the page No. 5
UNPACKING When unpacking, check to make sure the parts listed on page 11 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. OPERATION 1. You will need to prepare a 1/4” air connector (sold separately) to connect to the air in- let on the Nailer. First, wrap the 1/4” air connector (not included) with pipe thread seal tape before threading it into the Air Inlet (90). Connect the 3/8” ID Air Source Ho
Summary of the content on the page No. 6
TESTING THE FULL SEQUENTIAL SAFETY TRIP MECHANISM WARNING! Even though the nailer should be empty during this procedure, ALWAYS point the nailer at a piece of scrap wood when testing. 1. Make sure the tool is disconnected from the power supply. 2. Completely empty the Magazine (76) of nails. 3. The Nailer should not fire if the Safety (41) is not depressed against the workpiece. 4. Make sure the Trigger (47) and Safety (41) move freely, without sticking. Do not use nailer if Trigger or Safe
Summary of the content on the page No. 7
ILLUSTRATIONS Warning! Disconnect the Nailer from the air compressor whenever loading. FIGURE 2 FIGURE 1 Exhaust Cover (4) Tab (71) Trigger (47) Air Inlet (90) Latch (83) Safety (41) Magazine (76) FIGURE 4 FIGURE 3 Adjustment Knob (81) Angle Adjustment Holes Hex Bolt Tab (71) o o o 21 28 34 Pin in FIGURE 6 FIGURE 5 B o o 28 /34 o o 28 /34 Position o o 34 28 o 21 Plate (80) Pin in o 21 A o 21 Position SKU 97510 Page 7 For technical questions, please call 1-800-4
Summary of the content on the page No. 8
OPERATION Note: The Nailer may not work if there are only 2 or 3 nails left-see Note on page 6, bot- tom. 1. Set the proper angle of the Nailer for your application (a three step process): a. Pull back and engage the Tab (70), exposing three adjustment holes. Loosen the hex bolt and slide it into the appropriate hole (21°, 28°, 34°). Retighten the hex bolt securely, making sure it fits into the appropriate hole properly. See FIGURE 3. Gen- tly release the Tab (70). b. Remove the Adjustment
Summary of the content on the page No. 9
Anytime any maintenance or repairs are done (including clearing jams), FIRST: 1. Disconnect the Nailer from the air hose. 2. Empty the Magazine (76) completely. 3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any nails. 4. Always leave the Magazine (76) open during maintenance. The Magazine is spring-loaded and may cause parts or a nail to fly out of the Nailer. CLEARING JAMS 1. Disconnect tool from air hose. Always fire t
Summary of the content on the page No. 10
TROUBLESHOOTING Any internal repair should be performed by a qualified service technician. Symptom Cause Solution Top of tool or Trigger (47) 1. Loose Screws, 1. Verify screws are tight, leaks air, sluggish opera- 2. Worn or damaged O-rings or 2. Check/replace O-rings or seals tion, or will not operate seals 3. Use a compressor that delivers the proper 3. Inadequate air supply, CFM, 4. Inadequate lubrication, 4. Add air tool oil (not incl.), 5. Worn/damaged O-rings or 5. Check/replace O-rings
Summary of the content on the page No. 11
PARTS LIST Part Description Part Description Part Description 1 Screw 31 Screw 61 Bushing 2 Spring Washer 32 Washer 62 Screw 3 Bushing 33 Pin 63 Washer 4 Exhaust Cover 34 Pin 64 Turn Plate B 5 Seal 35 Guide Plate 65 Bushing 6 Screw 36 Spring 66 Coil Spring 7 Spring Washer 37 Screw 67 Coil Spring Base 8 Cylinder Cap 38 Bracket A 68 Pin 9 Gasket 39 Washer 69 Screw 10 O-ring 40 Screw 70 Tab 11 O-ring 41 Safety (Bracket B) 71 Feeder Shoe 12 Spring 42 Rubber Cover 72 Hex Bolt 13 Valve 43 Washer 73 Wa
Summary of the content on the page No. 12
ASSEMBLY DRAWING SKU 97510 Page 12 For technical questions, please call 1-800-444-3353. 93910
Summary of the content on the page No. 13
90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of pur- chase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, im- proper installation, no
