Summary of the content on the page No. 1
12V Lithium CordLess driLL
model 69360
set up and operating instruCtions
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
sa Ve this manuaL.
© ®
Copyright 2010 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may
Summary of the content on the page No. 2
notiCe is used to sa Ve this manuaL address practices not Keep this manual for the safety warnings related to personal injury. and precautions, assembly, operating, Caution, without the inspection, maintenance and cleaning safety alert symbol, is procedures. Write the product’s serial number used to address practices not in the back of the manual near the assembly related to personal injury. diagram (or month and year of purchase if product has no number). Keep this manual general
Summary of the content on the page No. 3
operating a power tool. do not use safety equipment may not provide a power tool while you are tired or adequate protection. Eye protection under the influence of drugs, alcohol must be ANSI-approved and breathing or medication. A moment of inattention protection must be NIOSH-approved for while operating power tools may result the specific hazards in the work area. in serious personal injury. 4. power tool use and care b. use personal protective equipment. a. do not force the power too
Summary of the content on the page No. 4
g. use the power tool, accessories drill and impact drill safety and tool bits etc. in accordance Warnings with these instructions, taking into account the working conditions and 1. hold power tools by insulated the work to be performed. Use of gripping surfaces when performing the power tool for operations different an operation where the cutting tool from those intended could result in a may contact hidden wiring or its own hazardous situation. cord. Contact with a ″live″ wire will
Summary of the content on the page No. 5
Do not place the charger on a flammable Your risk from these exposures varies, surface. Do not obstruct any vents on depending on how often you do this type the charger. especially avoid placing of work. To reduce your exposure to the charger on carpets and rugs; they these chemicals: work in a well ventilated are not only flammable, but they also area, and work with approved safety obstruct vents under the charger. equipment, such as those dust masks Place the charger on a stable, soli
Summary of the content on the page No. 6
blood circulation to the hand, past hand Lithium Battery safety Warnings injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. Lithium Batteries store a 2. Do not smoke during use. Nicotine Large amount oF energY and reduces the blood supply to the hands WiLL Vent Fire or expLode iF and fingers, incr
Summary of the content on the page No. 7
2. Double insulated tools may be used in grounding either of the 120 volt outlets shown in the t o preVent preceding illustration. (see outlets for eLeCtriC shoCK 2‑prong plug.) and death From inCorreCt grounding Wire extension Cords ConneCtion: note: Extension cords must not be used with Check with a qualified electrician this item’s charger. if you are in doubt as to whether the outlet is properly grounded. symbology do not modify the power cord plug provided with the tool. Do
Summary of the content on the page No. 8
Controls speCiFiCations 1. trigger: Charger Input 120V~ / 60Hz 0-350 RPM (1st gear) This is a variable speed tool. Motor Speed 0-1200 RPM (2nd gear) Squeeze the Trigger more to increase 12V, 1300mAh Lithium-Ion Battery speed, less to reduce speed. (ITEM 68059) The light will illuminate when the trigger Chuck Capacity 3/8" (10mm) is pressed. 2. direCtion setting: unpaCKing : (towards front of drill) Press switch from the right side When unpacking, make sure that the of the drill to make
Summary of the content on the page No. 9
Battery Pack operating instruCtions read the entire important Green saFetY inFormation Light section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Charging the Battery pack Red Light The Battery Pack (ITEM 68059) needs to be charged before first use. Recharge Charger the Battery after every use. 1. Remove the Battery Pack by pressing on 3. The green light will activate once the striped side tabs and sliding it out.
Summary of the content on the page No. 10
t ool set up general operating instructions t o preVent 1. Change Direction, Clutch, and Gear serious injur Y settings as desired, see page 8. From aCCidentaL Caution: t o prevent damage, do operation: not adjust any setting while drill is in release the t rigger and remove motion. the Battery pack before adjusting 2. Install bit as explained to the left. tool or installing accessories. 3. Insert Battery Pack into base of tool until Bit instaLLation: it clicks in place. 1. Caution! Let
Summary of the content on the page No. 11
Cleaning, maintenance, and maintenanCe and Lubrication ser ViCing 1. BeFore eaCh use, inspect the Procedures not specifically general condition of the tool. Check for explained in this manual must loose hardware, misalignment or binding be performed only by a qualified of moving parts, cracked or broken parts, technician. damaged electrical wiring, and any t o preVent other condition that may affect its safe serious injur Y operation. From aCCidentaL 2. aFter use, wipe external
Summary of the content on the page No. 12
t roubleshooting problem possible Causes Likely solutions Tool will not start. 1. Battery not installed or properly 1. Check that battery is properly installed and fully charged. charged. 2. Internal damage or wear. 2. Have technician service tool. (Wiring or Trigger, for example.) Performance 1. Accessory dull or damaged. 1. Keep cutting accessories sharp. Replace as decreases over time. needed. 2. Carbon brushes worn or 2. Have qualified technician replace brushes. damaged. Excessive nois
Summary of the content on the page No. 13
parts List and diagram part description Qty. part description Qty. 1 Keyless Chuck 1 12 Rear Cover 1 2 Front Cover 1 13 Wire 1 3 Screw 3 14 White LED 1 4 Screw 7 15 LED Cover 1 5 Gear Switch 1 16 Screw 3 6 Trigger 1 17 Terminal Board 1 7 Direction Switch 1 18 Screw 1 8 Gear Switch Spring 2 Battery Pack - ITEM 68059 19 1 9 Left Housing 1 (12V, 1300mAh Lithium-Ion) 10 Right Housing 1 20 Motor 1 11 Gear Box 1 21 Charger (not shown) 1 SKU 69360 For technical questions, please call 1800 ‑ 444 ‑ 3353.
Summary of the content on the page No. 14
To take advantage of this warranty, Limited 90 da Y WarrantY the product or part must be returned to us Harbor Freight Tools Co. makes every with transportation charges prepaid. Proof effort to assure that its products meet of purchase date and an explanation of the high quality and durability standards, and complaint must accompany the merchandise. warrants to the original purchaser that this If our inspection verifies the defect, we product is free from defects in materials and will eit
