Summary of the content on the page No. 1
1 HP cast Iron
sewage PumP
66351
set uP , oPeratIng, and maIntenance
InstructIons
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
sa Ve tHIs manual.
© ®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this
Summary of the content on the page No. 2
notIce is used to sa Ve tHIs manual address practices Keep this manual for the safety warn- not related to personal injury. ings and precautions, assembly, operat- cautIon, without ing, inspection, maintenance and cleaning the safety alert procedures. Write the product’s serial symbol, is used to address number in the back of the manual near the practices not related to assembly diagram (or month and year of personal injury. purchase if product has no number). Keep this manual and
Summary of the content on the page No. 3
ductor in the cord is the grounding d. do not operate this sewage wire. Do not connect the green or Pump if either the Power cord (1), green and yellow wire to a live termi- Power Plug (29), Housing (10), or nal. Base (27), appear cracked or dam- aged in any way. e. warnIng! do not repair a dam - aged power cord. always replace the cord before further use of this sewage Pump. f. do not place this sewage Pump in water with bare hands. always wear heavy-duty, insulated rubber gloves. Y
Summary of the content on the page No. 4
product, but must be supplied by the drip loop operator. outlet sa Ve tHese InstructIons. deVIce sPecIFIcatIons cord Electrical Information 120 V, 60 Hz, 10.5 AMPS 6. Use Drip-Loop to prevent water from accidentally entering the electrical Gallons Per Minute 110 power outlet. Use only with a GFCI Pump Motor 1 HP, 3450 RPM outlet. see second paragraph in “Power cord safety” section of this manual. unP acKIng When unpacking, check to make sure use and care that the item is intact and
Summary of the content on the page No. 5
refer to the Assembly Diagram near oPeratIng InstructIons the end of this manual. read the entIre ImPortant saFety InFormatIon section assemBly at the beginning of this manual including all text under 1. Thread a discharge hose, or pipe subheadings therein before set (not supplied) to the orifice on side of up or use of this product. Base (27). 1. Before operating the Sewage Pump, 2. If you use a check-valve (not sup- put on ANSI-approved safety gog- plied), mount the check valve hori-
Summary of the content on the page No. 6
warnIng: this sewage Pump contains maIntenance and dielectric motor oil for both lubri- ser VIcIng cation and heat transfer. It may be under pressure because of heat Procedures not specifically collection. let the sewage Pump explained in this manual cool for at least 2 hours before must be performed only by a inspecting, or servicing. this oil qualified technician. may be dangerous to the environ- t o PreVent ment. always dispose of used oil serIous Injury in compliance with all
Summary of the content on the page No. 7
t roubleshooting Problem Possible causes likely solutions Sewage Pump will not 1. No power at outlet. 1. Check power at outlet. start. 2. Circuit breaker tripped. 2. Check circuit breaker for outlet. 3. Cord not connected. 3. Check that cord is plugged in. 4. Water level too low. 4. Check water level. Low flow from 1. Possible excess solid debris lodged 1. Check and clean debris from discharge outlets. in Impeller. Impeller per instructions on Page 6. Sewage Pump starts 1. Possible back flow fr
Summary of the content on the page No. 8
Parts lIst Parts lIst Part description Q’ty Part description Q’ty 1 Power Cord 1 17 Motor Shaft 1 2 Screw 3/16 - 24 x 1/4 2 18 Motor 1 3 Cord Cover (Protector) 1 19 Washer 6202zz - 12.7 1 4 Screw 1/4 - 20 x 1/4 2 20 Mechanic Seal Typ 21 1 5 Handle 1 21 O-Ring 1 6 Washer 3/16 1 22 Motor Seat 1 7 Strain Relief 1 23 V-Seal 1 8 Screw 3/16 24 x 308 1 24 Impeller 1 9 1/4” NPT Oil Plug 1 25 Flat Screw 3/16 - 24 x 5/8 6 10 Pump Motor Housing 1 26 Packing Gasket 1 11 Washer 3/16 x 1/4 2 27 Base 1 12 Capa
Summary of the content on the page No. 9
lImIted 90 day warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this prod- uct is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installat
