Hitachi nt65ks user manual

User manual for the device Hitachi nt65ks

Device: Hitachi nt65ks
Category: Nail Gun
Manufacturer: Hitachi
Size: 3.12 MB
Added : 12/28/2013
Number of pages: 52
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Hitachi nt65ks. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Hitachi nt65ks.

For your convenience

If looking through the Hitachi nt65ks user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Hitachi nt65ks on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Hitachi nt65ks to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Hitachi nt65ks User manual - Online PDF
Advertisement
« Page 1 of 52 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Hitachi nt65ks but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Hitachi nt65ks. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

Instruction and safety manual
Manuel d’instructions et de sécurité
Manual de instrucciones y de seguridad
Nailer
Model
NR 65AK
Cloueur
Modèle
Clavador
NR 65AK (S)
Modelo











"STRAP-TITE™"












Summary of the content on the page No. 2

CONTENTS English Page Page IMPORTANT INFORMATION ..................................................3 BEFORE OPERATION ............................................................10 DEFINITIONS OF SIGNAL WORDS ....................................... 3 WORKING ENVIRONMENT ............................................10 AIR SUPPLY .....................................................................10 SAFETY LUBRICATION ..................................................................11 IMPORTANT S

Summary of the content on the page No. 3

English IMPORTANT INFORMATION Read and understand tool labels and all of the operating instructions, safety precautions and warnings in this manual before operating or maintaining this nailer. Failure to follow warnings could result in DEATH or SERIOUS INJURY. Most accidents that result from the operation and maintenance of Nailers are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it oc

Summary of the content on the page No. 4

English SAFETY IMPORTANT SAFETY INSTRUCTIONS MMMMFOR USING NAILERSMMlMM READ AND UNDERSTAND ALL INSTRUCTIONS DANGER 1. OPERATORS AND OTHERS IN WORK AREA MUST WEAR SAFETY GLASSES WITH SIDE SHIELDS. When operating the Nailer, always wear safety glasses with side shields, and make sure others in work area wear safety glasses, too. Safety glasses must conform to the requirements of American National Standards Institute, ANSI Z87.1 and provide protection against flying particles both from the front a

Summary of the content on the page No. 5

English SAFETY — Continued WARNING 6. NEVER POINT TOOL AT YOURSELF OR OTHERS 12. KEEP WORK AREA CLEAN. IN WORK AREA. Cluttered areas invite injuries. Clear all work areas of Always assume the Nailer unnecessary tools, debris, furniture, etc. contains fasteners. Never point the Nailer at 13. NEVER USE IN PRESENCE OF FLAMMABLE yourself toward yourself or LIQUIDS OR GASES. others, whether it contains The Nailer produces sparks during operation. fasteners or not. Never use the Nailer in sites contai

Summary of the content on the page No. 6

English SAFETY — Continued WARNING Never attempt to clear a jam or repair the Nailer 20. KEEP FACE, HANDS AND FEET AWAY FROM unless you have disconnected air hose from the Nailer FIRING HEAD AT ALL TIMES. and removed all remaining nails from the Nailer. Never place your face, hands or feet near the firing The Nailer should never be left unattended since head. people who are not familiar with the Nailer might A serious injury can result if the nails are deflected by handle it and injure the thems

Summary of the content on the page No. 7

English SAFETY — Continued WARNING 36. USE ONLY GENUINE HITACHI HEAT TREATED 38. BEFORE EACH FIRING, BE SURE TO POSITION NAILS FOR HITACHI NR65AK. AND INSERT THE FIRST NAIL POINT THROUGH Use only genuine HITACHI heat treated nails of (8d) THE METAL HOLE. .131 × 1-1/2", (10d) .148 × 1-1/2", (10d) .148 × 2-1/2", This tool and nails are designed for metal connector (16d) . 162 × 2-1/2" for HITACHI NR65AK to avoid with pre-punched holes. serious injury from ricocheting nails. Drive nails into work s

Summary of the content on the page No. 8

English OPERATION NOTE: The information contained in this Manual is designed to assist you in the safe operation of the Nailer. Some illustrations in this Manual may show details or attachments that differ from those on your own Nailer. NAME OF PARTS Top Cover Magazine Cover Exhaust Cover Body Nail Gate Trigger Cap Piston O-Ring Piston Driver Blade Magazine Nose Nail Feeder Feeder Plate Knob Push Lever SPECIFICATIONS Model NR65AK NR65AK (S) 2 Operating pressure 80 – 120 psi (5.4 – 8.3 bar 5.5 –

Summary of the content on the page No. 9

English NAIL SELECTION WARNING  Use only genuine HITACHI heat treated nails for this NR65AK to avoid serious injury from ricocheting nails. The use of any other nails and non-heat treated nails could result in dangerous tool malfunction and/or nail malfunction, causing serious injury.  Select adequate nail size to meet proper metal hardware requirement needed for application, designed by metal hardware manufacturer and regulated by the applicable building code. Only nails shown in the Table be

Summary of the content on the page No. 10

English 2. Filter-Regulator-Lubricator APPLICATIONS  Use a regulator with a pressure range of 0 – 120 psi 2 (0 – 8.3 bar 0 – 8.5 kgf/cm ).  Filter-regulator-lubricator units supply an optimum DANGER condition for the Nailer and extend the Nailer life. These units should always be used. Filter .............The filter removes moisture and dirt  Pre-punched holed metal connector to wood stud mixed in compressed air. installation only. Drain daily unless fitted with an  Never drive nails into me

Summary of the content on the page No. 11

English 5. Air consumption TESTING THE NAILER Using the Air consumption table and the Air compressor size formula, find a correct compressor DANGER size.  Operators and others in Air consumption table work area MUST wear psi 80 90 100 safety glasses with side Operating pressure (bar) (5.5) (6.2) (6.9) shields which conforms 2 (kgf/cm ) (5.6) (6.3) (7) to ANSI Z87.1 3 specifications. ft /cycle .05 .056 .063 Air consumption (ltr/cycle) (1.4) (1.6) (1.8) Air compressor size formula WARNING Amount

Summary of the content on the page No. 12

English Before actually beginning the nailing work, test the Nailer (3) With finger off the trigger, depress the push lever by using the checklist below. Conduct the tests in the against the workpiece. following order. If abnormal operation occurs, stop using the Nailer and  THE NAILER MUST NOT DRIVE. contact a Hitachi authorized service center immediately. (1) DISCONNECT AIR HOSE FROM NAILER. REMOVE ALL NAILS FROM NAILER.  ALL SCREWS MUST BE TIGHTENED. If any screws are loose, tighten them. D

Summary of the content on the page No. 13

English Adjust the air pressure at recommended operating (2) Insert nail strips from rear of magazine. 2 pressure 80 – 120 psi (5.4 – 8.3 bar 5.5 – 8.5 kgf/cm ) according to the length of nails and the hardness of workpiece. The correct air pressure is the lowest pressure which will do the job. Using the Nailer at a higher than required air pressure unnecessarily over stresses the Nailer. LOADING NAILS WARNING (3) Slide the nail strip forward in the magazine.  When loading nails into Nailer, Th

Summary of the content on the page No. 14

English After the nail is driven, completely release the trigger NAILER OPERATION and lift the tool off the work surface. Read section titled “SAFETY”(pages 4 – 7). This tool is not designed for contact trip operation (bounce fire), and not available for contact trip valve units. DANGER And this tool has a new push lever (safety) mechanism, this is a different push lever mechanism from another  Operators and others in nailers. The push lever is positioned on top at non firing work area MUST wea

Summary of the content on the page No. 15

English (2) Pull the trigger to drive a nail with keeping your face and hands away from the nose muzzle. (3) Remove finger from the trigger. Remove the nailer from workpiece and reposition into the next pre-punched metal hole. Repeat same process. (4) When charge the nail length, remove the all nails in the magazine. WARNING  Keep your finger off the trigger except during nailing operation, because serious injury could result if the push lever accidentally contacts you or others in work area. 

Summary of the content on the page No. 16

English MAINTENANCE NOTE: The information contained in this Manual is designed to assist you in the safe maintenance of the Nailer. Some illustrations in this Manual may show details or attachments that differ from those on your own Nailer. MAINTENANCE AND INSPECTION Read section titled “SAFETY” (pages 4 – 7). WARNING  Disconnect air hose and remove all nails from Nailer when: 1) doing maintenance and inspection; and Warning Label 2) clearing a jam. 4. Maintenance chart (See page 17) 1. Inspect

Summary of the content on the page No. 17

English Maintenance chart ACTION WHY HOW Drain air line filter daily. Prevent accumulation of moisture Open manual petcock. and dirt. Keep lubricator filled. Keep the Nailer lubricated. Fill with Hitachi pneumatic tool lubricant. Clean filter element — then blow Prevent clogging of filter with dirt. Follow manufacturer’s instructions. air through filter in direction opposite to normal flow. Clean magazine and feeder Prevent a jam. Blow clean daily. mechanism. Keep push lever working properly. Pr

Summary of the content on the page No. 18

Français INFORMATION IMPORTANTE Lire et bien assimiler toutes les étiquettes de l’outil ainsi que toutes les instructions de fonctionnement, les consignes de sécurité et les avertissements de ce mode d’emploi avant d’utiliser ou d’entretenir ce cloueur. Le non respect des avertissements pourrait entraîner la MORT ou des BLESSURES GRAVES. La plupart des accidents résultant de l’utilisation ou de l’entretien des cloueurs sont dus au non respect de certaines consignes et précautions de sécurité élé

Summary of the content on the page No. 19

Français SECURITE CONSIGNES DE SECURITE IMPORTANTES POUR L’UTILISATION DU CLOUEUR LIRE ET BIEN COMPRENDRE TOUTES CES INSTRUCTIONS. DANGER 1. LES OPÉRATEURS ET LES AUTRES PERSONNES DANS L’AIRE DE TRAVAIL DOIVENT PORTER DES LUNETTES DE PROTECTION AVEC VISIÈRES LATÉRALES. Quand on utilise le cloueur, toujours porter des lunettes de protection avec visières latérales, et veiller à ce que les autres personnes dans la zone de travail en portent également. Les lunettes de protection devront respecter l

Summary of the content on the page No. 20

Français SECURITE — suite AVERTISSEMENT 6. NE JAMAIS DIRIGER L’OUTIL VERS SOI NI VERS 11. RANGER LE CLOUEUR CORRECTEMENT. QUELQU’UN D’AUTRE DANS L’AIRE DE Quand on ne s’en sert pas, ranger le cloueur dans un endroit sec. Le ranger hors de portée des enfants. TRAVAIL. Verrouiller la zone de rangement. Toujours supposer que le cloueur renferme des clous. 12. MAINTENIR L’AIRE DE TRAVAIL PROPRE. Ne jamais diriger le cloueur vers Une aire encombrée invite les blessures. Enlever tous soi ni vers quelq


Alternative user manuals
# User manual Category Download
1 Hitachi NR 90GC2 User manual Nail Gun 65
2 Hitachi NR 90GC User manual Nail Gun 8
3 Hitachi NR 90GR User manual Nail Gun 13
4 Hitachi NT 32AE2 User manual Nail Gun 9
5 Hitachi nr65AK User manual Nail Gun 8
6 Hitachi NR 90GR2 User manual Nail Gun 9
7 Hitachi NT 50AE2 User manual Nail Gun 33
8 Hitachi NT 65GA User manual Nail Gun 12
9 Hitachi NT 65GS User manual Nail Gun 27
10 Hitachi NT 65MA4 User manual Nail Gun 11
11 Hitachi NT 50GS User manual Nail Gun 15
12 Hitachi NT 65GB User manual Nail Gun 27
13 Hitachi NV 45AB2 User manual Nail Gun 6
14 Hitachi NV50AA User manual Nail Gun 8
15 Hitachi NR90AA User manual Nail Gun 1
16 Airfree Service Parts UF55 User manual Nail Gun 2
17 Airfree Service Parts UF55-RFK-500 User manual Nail Gun 2
18 Airfree Service Parts UF55w User manual Nail Gun 1
19 AllTrade AIR-PLUS 691164 User manual Nail Gun 0
20 AllTrade AIR-PLUS 691165 User manual Nail Gun 8