Summary of the content on the page No. 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
EVERLAST
Assembly Instruction
MULTI PURPOSE BENCH
Parts List
EVE-540
Warranty
Ordering Parts
Model
EVE-540
Retain This
Manual for
Reference
09-30-05
Made under license from trademark owner Everlast
OWNER'S
Worldwide Inc., New York.
MANUAL
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (
Summary of the content on the page No. 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK……….....…....................................................................... 4 ASSEMBLY INSTRUCTIONS........................................................................... 5 EXPLODED DIAGRAM...........................................................
Summary of the content on the page No. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one perso
Summary of the content on the page No. 4
WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Front Stabilizer. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown. 3
Summary of the content on the page No. 5
HARDWARE PACK 4
Summary of the content on the page No. 6
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Main Frame (#1) to the Front & Rear Stabilizers (#2 & 3). Secure each end with two M10 x ¾” Allen Bolts (#36) and ∅ ¾” Washers (#42). Attach a Lock Knob (#23) to the hole underneath the Main Frame. B.) Slide the Sliding Block (#8)
Summary of the content on the page No. 7
STEP 2 (See Diagram 2) A.) Attach four Bushings (#27) to a Seat Support Frame (#6). B.) Attach a Backrest Support (#7) to the rear of the Seat Support Frame (#6). Align the holes and secure them with one M10 x 1 ¾” Allen Bolt (#37) and ∅ ¾” Washer (#42). Repeat the same procedure to install the other side. C.) Attach two Bushings to the pivot on the Sliding Block (#8). Attach two Bushings to each Backrest Supports (#7). Align the holes and secure them with one M10 x 6 ¾” Allen Bolt
Summary of the content on the page No. 8
STEP 3 (See Diagram 3) A.) Place the Backrest Board (#14) onto the Backrest Supports (#7). Secure it with four M8 x 2” Allen Bolts (#40) and ∅ 5/8” Washers (#43). B.) Place the Seat Pad (#13) onto the Seat Support Frames (#6). Secure it with four M8 x 2” Allen Bolts (#40) and ∅ 5/8” Washers (#43). DIAGRAM 3 7
Summary of the content on the page No. 9
STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#5) to the open bracket on the Main Frame (#1). Secure it with an Axle (#17), two M10 x ¾” Allen Bolts (#36), and two ∅ ¾” Washers (#42). B.) Insert a Spring (#16) into the slot at the front of Main Frame. Secure the Spring to the slot with one Spring Spacer (#11) and M6 x ½” Philips Screw (#45). Insert one side of the U-shaped Lock Pin (#12) into the Slot. C.) Attach the Bar Holder (#26) to the Leg Developer (#5). Secure it with a
Summary of the content on the page No. 10
STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#15) to the Arm Curl Stand (#4). Secure it with two M8 x 5/8” Allen Bolts (#41) and two ∅ 5/8” Washers (#43). Insert the Arm Curl Stand into the front opening on the Main Frame (#1). B.) Use the Lock Knob to hold the desired Arm Curl height. DIAGRAM 5 9
Summary of the content on the page No. 11
10
Summary of the content on the page No. 12
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Main Frame 1 2 Front Stabilizer 1 3 Rear Stabilizer 1 4 Arm Curl Stand 1 5 Leg Developer 1 6 Seat Support Frame 2 7 Backrest Support 2 8 Sliding Block 1 9 Incline Adjustment Bar 1 10 Foam Tube 3 11 Spring Spacer 1 12 U-shaped Lock Pin 1 13 Seat Pad 1 14 Backrest Board 1 15 Arm Curl Pad 1 16 Spring 2 17 Axle 1 18 Ø 2 3/8” Bushing 2 19 Ø 1 ½” Bushing 2 20 Olympic Sleeve 1 21 L-shaped Lock Pin 1 22 Spring Clip 1 23 Lock Knob 2
Summary of the content on the page No. 13
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Custo
