Summary of the content on the page No. 1
RCR-2
Operating instruction GB
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC
!
SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE THE EXCLAMATION
THE LIGHTNING
RISK OF ELECTRIC POINT WITHIN THE
FLASH AND ARROW-
SHOCK, DO NOT REMOVE TRIANGLE IS A WARN-
HEAD WITHIN THE
THE BACK, NO USER SER-
TRIANGLE IS A WARN- ING SIGN ALERTING
VICEABLE PARTS INSIDE. YOU OF IMPORTANT
ING SIGN ALERTING
REFER SERVICING TO INSTRUCTIONS
YOU OF “DAN
Summary of the content on the page No. 2
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purp
Summary of the content on the page No. 3
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. GB 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug
Summary of the content on the page No. 4
Main features ( 1 ) 14 station memories ( 7 each on AM/FM bands ) ( 2 ) Digital radio controlled clock with date display Date and time displays are checked and if necessary corrected daily with an exact radio controlled time antenna signal ( 3 ) Nap timer Adjustable from 10-120 minutes ( 4 ) Alarm with Humane Wake System ( HWS ) The alarm begins quietly and gradually becomes louder before switched off ( buzzer alarm only ) ( 5 ) Radio alarm Woken up by the favorite station ( 6 ) Two independen
Summary of the content on the page No. 5
GB 4
Summary of the content on the page No. 6
5
Summary of the content on the page No. 7
Controls 1 Power on/off and Sleep timer 2 Nap timer 3 Display button to display time and radio frequency 4 Display backlight on/off button GB 5 Buzzer alarm level adjustment 6 RESET 7 Time zone adjustment 8 Date adjustment 9 Time adjustment 10 Alarm 2 button 11 Alarm 1 button 12 Headphones socket 13 Time/Date/Alarm set button 14 LCD display 15 Tuning Up/Down and Snooze button 16 Station memories and alarm week days
Summary of the content on the page No. 8
LCD display A Radio band and a.m./p.m. display B Time set C Daylight Saving Time (D.S.T.) D Alarm indicator E Sleep timer F Nap timer G Alarm a.m./p.m. indicator H Date I Week day J Month/Date/Year/alarm time K Radio controlled symbol L Station memory number and second indicator M Minute ( for Nap and Sleep timer ) N Frequency/Time display 7
Summary of the content on the page No. 9
Notes on safety Only operate this appliance with a power supply of 110-120 Volt/ 50-60 Hz . If you intend not using the appliance for a longer period of time ( eg. Holidays), pull the plug out of the mains socket to ensure a complete separation from the power supply. GB Protect the appliance from heat and moisture. Do not open the appliance and if it should require servicing, please refer to a licensed electrical workshop. Operation Atomic clock operation The Sangean RCR 2 consists of a cr
Summary of the content on the page No. 10
Set time Zone Switch [7] located on bottom of clock to your correct zone as illustrated. After the ATS program completes the AM/FM frequency set up the following display — : — will appear and the symbol will blink indicating the radio is searching for the radio controlled signal. Once the radio receives the radio controlled signal the correct time and date will be set automatically. Once the correct time and date have been set, the symbol will stop blinking but the symbol will rem
Summary of the content on the page No. 11
Note: If there is Daylight Saving Time ( D.S.T.) system in your place, after pressing SET button, press Mode button once will advance one hour on time setting, Display will show D.S.T. symbol indicating the time is under D.S.T. status. GB DATE Press DATE button, display DATE will blink. Press SET button, display will blink year with a beep and a small Y (year) will appear, 1. Set the year with key + or -. 2. Press SET button again and follow the setting of year to set the month and date . 3.
Summary of the content on the page No. 12
Radio operation Turn on the radio with the Power on/off key 1. Tune into desired stations Manual station selection 1. With the key 15 Tuning + and -, you can tune into the frequency of your desired stations. 2. Scanning tuning Press and hold key 15 + or – for more than 0.5 seconds and release, the radio will search for the next station. Storing the preset stations Tune into the stations. Select a memory preset button and press for more than 2 seconds until a confirmed beep sounds
Summary of the content on the page No. 13
Alarm Clock Alarm setting can be done while the appliance power is during on or off position. The alarm clock is equipped with two alarm systems which can be operated independently of each other either with Human Wake GB System buzzer or with a radio (radio alarm clock ). Alarm with radio 1. Select the desired station by station memory button 1-7 or simply tune the radio station. 2. Set the desired radio alarm volume. 3. Select alarm system 1 or 2 by pressing the alarm 1 or 2 button. D
Summary of the content on the page No. 14
Note: If you like to be awoken by the radio station you are listening, press Alarm system 1 or 2 for more than 2 seconds, the appliance will store the radio alarm station, then follow above procedures 2-8 to set radio alarm. Alarm with HWS alarm buzzer 1. Select alarm system 1 or 2 by pressing the alarm 1 or 2 button (11 or 10). Display will blink selected alarm system symbol. 2. Press alarm SET button 13, display will blink both alarm hour and alarm mode with a beep. 3. Press alarm mode
Summary of the content on the page No. 15
Cancel alarm setting. If you do not wish to be woken up at the alarm time you have set, you can cancel the alarm function. 1. Select alarm system 1 or 2 by pressing the alarm 1 or 2 button (key 11 or 10). GB 2. Press SET button , the alarm mode symbol will blink with a beep. 3. Press alarm MODE button 17 one or two times (depending you were in alarm radio or alarm buzzer status ) till display blink . 4. Press alarm 1 or 2 button again to confirm alarm cancellation. The
Summary of the content on the page No. 16
Nap timer With key 2, you can select the period for the short term alarm in 10 minutes steps from 10-120 minutes. The Nap timer starts when you release the key. NAP will appear on display. The alarm signal sounds after the period of time which you have set. If you wish to turn off the Nap timer before the time is up, simply adjust the number of minutes by pressing NAP key to OFF and release. NAP will disappear from display. When Nap timer signal is on, turn off the timer signal by pressing key
Summary of the content on the page No. 17
Alarm level adjustment With alarm level adjustment switch 5, you may select required alarm signal level. Note: GB Alarm level adjustment works only for buzzer alarm. Display backlight on/off Key 4 provides you to select whether you require to illuminate the display. Time zone switch Time Zone Switch [7] should be set to zone where clock/radio is to be used. Troubleshooting /RESET If the radio fails to operate correctly or some digits on the display are missing or incomplete, carry out th
Summary of the content on the page No. 18
Technical data Power supply 110-120 Volt/50-60 Hz Output Power 800 mW max Power consumption 7W (max.). Frequency coverage FM 87.50 - 108 .0 MHz AM 520 - 1710 kHz Technical data subject to changes without prior notice. 17
Summary of the content on the page No. 19
381J412A
