Summary of the content on the page No. 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
MARCY PLATINUM
Safety Notice
MP-2105 HOME GYM
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MP-2105
Retain This
Manual for
Reference
10-26-06
OWNER'S
MANUAL
®
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.
Summary of the content on the page No. 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK……….....…....................................................................... 4 ASSEMBLY INSTRUCTIONS........................................................................... 7 WEIGHT RESISTANCE CHART..................................................
Summary of the content on the page No. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a
Summary of the content on the page No. 4
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3
Summary of the content on the page No. 5
HARDWARE PACK 4
Summary of the content on the page No. 6
HARDWARE PACK 5
Summary of the content on the page No. 7
HARDWARE PACK 6
Summary of the content on the page No. 8
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Insert two Guide Rods (#16) into the holes on the Rear Stabilizer (#15). Secure each Guide Rod with one M10 x ¾” Allen Bolt (#78) and Ø ¾” Washer (#92) from bottom. Attach two Rubber Bumpers (#55) onto top of the two Guide Rods and slide down
Summary of the content on the page No. 9
DIAGRAM 1 8
Summary of the content on the page No. 10
STEP 2 (See Diagram 2) A.) Attach the Upper Frame (#1) onto the two Guide Rods (#16). Secure it with two M10 x ¾” Allen Bolts (#78) and ∅ ¾” Washers (#92). DO NOT tighten the Bolts yet. B.) Place the Upper Frame (#1) onto the Vertical Frame (#4). Secure it with two M10 x 2 ¾” Carriage Bolts (#90), one 4 ¾” x 2 ¾” Bracket (#25), two ∅ ¾” Washers (#92), and two M10 Aircraft Nuts (#91). C.) Securely tighten all Nuts and Bolts previously installed. D.) Attach the Seat Support Frame (#7) t
Summary of the content on the page No. 11
STEP 3 (See Diagram 3) A.) Attach the Front Press Base (#2) to the Upper Frame (#1). Secure it with one 6 ¾” Front Press Base Axle (#29), two Ø 1 ¼” Washers (#59), and two M10 Aircraft Nuts (#91). B.) Attach the Front Press (#3) to the Front Press Base (#2). Secure it with one 7 ½” Front Press Axle (#30), two Ø1 ¼” Washers (#59), and two M10 Aircraft Nuts (#91). C.) Thread the T-shaped Lock Pin (#39) into the hole on the Front Press to obtain the desired Front Press position. D.
Summary of the content on the page No. 12
DIAGRAM 3 11
Summary of the content on the page No. 13
STEP 4 (See Diagram 4) A.) Attach the Seat (#32) to the Seat Post (#6). Secure it with two M8 x 1 5/8” Allen Bolts (#86) and Ø 5/8” Washers (#88). B.) Insert the Seat Post into the opening on the Seat Support Frame (#7). Thread the Lock Knob (#40) into the hole on the Seat Support Frame to lock the Seat at selected height. C.) Insert the Foam Tube (#23) halfway through the hole on the Leg Developer (#8). Push two Foam Rolls (#48) onto the Foam Tube from both ends. Plug two Foam Rol
Summary of the content on the page No. 14
STEP 5 (See Diagram 5) A.) Slide the Right Butterfly (#10) onto the right axle on the Butterfly Base (#13). B.) Insert the Butterfly Handle (#9) into the pivot on the Right Butterfly. Secure it with one M10 x ¾” Allen Bolt (#78) and ∅ 1 ¼” Washer (#59) from the bottom. C.) Repeat Procedures A and B above to install the other side. Do not over tighten the Bolts. Make sure the Handles are able to swivel. DIAGRAM 5 13
Summary of the content on the page No. 15
CABLE LOOP DIAGRAM 14
Summary of the content on the page No. 16
STEP 6 (See Diagram 6 & Upper Cable Loop Diagram) A.) Attach the 163” Upper Cable (#33) to the opening on the front of Upper Frame (#1). Make sure the ball stopper is underneath the Frame. Attach a Pulley (#47) to the Cable. B.) Secure the Pulley to the opening with one M10 x 3 ½” Allen Bolt (#77), two Pulley Bushings (#49), and one M10 Aircraft Nut (#91). C.) Draw the Cable over the Pulley along the Upper Frame towards the back of the machine to the opening in the middle of Upper
Summary of the content on the page No. 17
DIAGRAM 6 16
Summary of the content on the page No. 18
Upper Cable Loop Diagram 17
Summary of the content on the page No. 19
STEP 7 (See Diagram 7 & Lower Cable Loop Diagram) A.) Attach the 164” Lower Cable (#35) to the opening on the Leg Developer (#8). Attach a Pulley (#47) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#84), two ∅ 7/8” Leg Developer Pulley Bushings (#52), and one M10 Aircraft Nut (#91). B.) Draw the Cable underneath the Pulley to the open bracket on the Front Base Frame (#12). Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#83), two ∅ ¾” Washers
Summary of the content on the page No. 20
DIAGRAM 7 19
