Summary of the content on the page No. 1
USB Enclosure
ACS-100
User’s Guide
R
Summary of the content on the page No. 2
Copyright ©2004 Adaptec, Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent of Adaptec, Inc., 691 South Milpitas Blvd., Milpitas, CA 95035. Trademarks Adaptec and the Adaptec logo are trademarks of Adaptec, Inc., which may be registered in some jurisdictions. Microsoft, Windows 98SE, Windows 2000, Windo
Summary of the content on the page No. 3
Limited 1-Year Hardware Warranty 1. Adaptec, Inc. (“Adaptec”) warrants to the purchaser of this product that it will be free from defects in material and workmanship for a period of one (1) year from the date of purchase. If the product should become defective within the warranty period, Adaptec, at its option, will repair or replace the product, or refund the purchaser’s purchase price for the product, provided it is delivered at the purchaser’s expense to an authorized Adaptec service faci
Summary of the content on the page No. 4
Regulatory Compliance Statements Federal Communications Commission Radio Frequency Interference Statement WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference
Summary of the content on the page No. 5
In this Guide... Kit Contents 5 System Requirements 5 Getting Started Checklist 6 Installing the Device Driver–Windows 98SE Only 6 Installing a Disk Drive 7 Connecting and Powering On 9 Next Steps 9 Disconnecting Your USB Enclosure 10 Troubleshooting 11 This User’s Guide explains how to install and connect your ® Adaptec ACS-100 USB Enclosure. 4
Summary of the content on the page No. 6
Kit Contents ■ Adaptec ACS-100 USB Enclosure ■ One enclosure stand ■ One power adapter ■ One high-quality USB cable ■ One bag of screws ■ CD, including device drivers and documentation A disk drive is not included in the kit. The Adaptec ACS-100 USB Enclosure supports 3.5-inch IDE hard disk drives. System Requirements To successfully install and use your Adaptec ACS-100 USB Enclosure, your computer must meet these requirements: ® ® ■ Microsoft Windows computers must be running Windows XP, Win
Summary of the content on the page No. 7
Getting Started Checklist Complete these steps to install and begin using your Adaptec ACS-100 USB Enclosure: ❏ Install the device driver—Windows 98SE only (see below). ❏ Install a disk drive (see page 7). ❏ Connect the enclosure and power it on (see page 9). ❏ Prepare the disk drive for use (see page 9). Installing the Device Driver–Windows 98SE Only Note: Windows XP/2000/Me and Macintosh users—No driver installation is required. Your Adaptec ACS-100 USB Enclosure works with the drivers buil
Summary of the content on the page No. 8
Installing a Disk Drive Before you begin, ensure that you are installing the proper disk drive. The Adaptec ACS-100 USB Enclosure supports 3.5-inch IDE hard disk drives only. Note: You need a Phillips screwdriver to complete this task. To install a disk drive into your USB Enclosure: 1 Use a screwdriver to remove the two screws on the back of the enclosure. 2 Remove the enclosure’s back panel, as shown below, and slide out the disk drive tray. 3 Connect the disk drive tray’s internal power c
Summary of the content on the page No. 9
4 Place the disk drive into the disk drive tray and secure it, using the four screws included in the kit. 5 Slide the disk drive tray into the enclosure and replace the back panel, then secure it with the screws you removed in Step 1 on page 7. 8
Summary of the content on the page No. 10
Connecting and Powering On Note: Windows 98SE users only—You must install the device drivers before connecting and powering on the USB Enclosure. To connect the cables and power on: 1 Use the included USB cable to connect the enclosure to an available USB port on your computer. 2 Use the included power adapter to connect the enclosure to a grounded power supply. 3 Power on the enclosure by pushing the on/off switch on the back of the enclosure to the I position. The LED on the front of the e
Summary of the content on the page No. 11
Disconnecting Your USB Enclosure To disconnect your USB Enclosure from your computer, follow the instructions for your operating system. Windows You must use the Unplug or Eject Hardware Wizard to properly disconnect the USB Enclosure from your computer. To disconnect the enclosure: 1 Click the Unplug or Eject Hardware Wizard icon (shown at right) on your system tray, which is in the bottom right corner of your screen. 2 Click USB Mass Storage Device, then click Stop. A message appears telli
Summary of the content on the page No. 12
Troubleshooting If you have problems installing or using your Adaptec ACS-100 USB Enclosure, work through this list of suggestions: ■ Ensure that the disk drive has been properly installed. ■ Try connecting the enclosure to your computer through a different USB port. ■ Try connecting the enclosure to your computer using a different USB cable. ■ Try connecting the enclosure to a different power source. ■ Windows 98SE users—If you connected and powered on your USB Enclosure before you installe
Summary of the content on the page No. 13
R Adaptec, Inc. 691 South Milpitas Boulevard Milpitas, CA 95035 USA ©2004 Adaptec, Inc. All rights reserved. Adaptec and the Adaptec logo are trademarks of Adaptec, Inc. which may be registered in some jurisdictions. Stock Number: CDP-00042-01-A, Rev. A, LB 12/04
