Summary of the content on the page No. 1
SBC Series
Single Board Computer Full Size PICMG
with LAN x 2, VGA, Audio
SPI-8450-LLVA
User’s Manual
CONTEC CO.,LTD.
Summary of the content on the page No. 2
Copyright Copyright 2003 CONTEC CO., Ltd. All Rights Reserved. No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO., Ltd. CONTEC Co., Ltd. makes no commitment to update or keep current the information contained in this document. The information in this document is subject to change without notice. All relevant issues have been considered in the preparation of this document. Should you notice an omission or any questionable item
Summary of the content on the page No. 3
Limited One Year Warranty CONTEC Industrial CPU card is warranted by CONTEC CO., Ltd. to be free from defects in material and workmanship for up to one year from the date of purchase by the original purchaser. Repair will be free of charge only when this device is returned freight prepaid with a copy of the original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office from which it was purchased. This warranty is not applicable for scratches or normal wear
Summary of the content on the page No. 4
Table of Contents Table of Contents CHAPTER 1 INTRODUCTION .................................................................................1 1.1 Specification........................................................................................................... 1 1.2 Mechanical & Environmental................................................................................. 3 1.3 Check List ......................................................................................................
Summary of the content on the page No. 5
Table of Contents 2.21 ATX power control Connector: CN21 ................................................................. 24 2.22 +12V power supply Connector :PW2................................................................... 24 CHAPTER 3 JUMPER SETTING ...........................................................................25 3.1 Clear CMOS Content: JBAT1.............................................................................. 25 3.2 RS-232C/422/485 Selector: JRS1 & JRS2...........
Summary of the content on the page No. 6
Table of Contents 8.9. PC Health Status ................................................................................................ 103 8.10. Frequency/Voltage Control ................................................................................ 104 8.11. Defaults Menu.................................................................................................... 105 8.12. Supervisor/User Password Setting ..................................................................... 106 8.13.
Summary of the content on the page No. 7
Table of Contents vi SPI-8450-LLVA
Summary of the content on the page No. 8
CHAPTER 1 – Introduction Chapter 1 Introduction 1.1 Specification Processor Socket: Socket 478 Processor: Intel(R) Pentium(R) 4 Processor 1.7GHz - 2.4GHz , Intel(R) Celeron(R) Processor 1.7GHz to 2.0GHz. (Package Type: 478pin PPGA FC-PGA2, CPU Core: Northwood Core only) Bus Clock Rate(FSB): 400/533 MHz Chipset: Intel 845GV Chipset includes GMCH (Graphics and Memory Controller Hub), ICH4 (I/O Controller Hub) and FWH (Firm Ware Hub) Memory Sockets: Two DIMM 184-pi
Summary of the content on the page No. 9
CHAPTER 1 – Introduction VGA Controller: Include Chipset(GMCH) VRAM shares 64MB(max.) from the main memory. One HD-sub type 15 pins connector for analog display. Audio: AC97 CODEC. 10pin header for speaker-out, line-in, microphone. LAN: Two RJ-45 connectors on board Intel ICH4 integrated with Intel 82562EM chipset support 10/100- base-TX Intel 82540 Giga LAN chipset support 10/100/1000-base-T RTC: battery backup by Lithium Battery The clock is accurate to ±3 minutes/month at 2
Summary of the content on the page No. 10
CHAPTER 1 – Introduction 1.2 Mechanical & Environmental DC Power Requirements +5VDC ± 5 % +12VDC ± 5 % +5VSB ± 5 % (Only at the time of ATX power supply use) Power Consumption (Intel(R) Pentium(R) 4 Processor 2.4 GHz ): +5VDC @ 5.40A max. +12VDC @ 6.20A max. +5VSB @ 0.65A max. Operating Temperature: 0 - 50°C (32°F to 122°F) Storage Temperature: -20 - 80°C (-4°F to 176°F) Operating Humidity: 10% - 90%RH (non-condensing) Floating dust particles: Not to be excessive Corrosive gases:
Summary of the content on the page No. 11
CHAPTER 1 – Introduction 1.3 Check List Please check that your package is complete and contains the items below. If you discover damaged or missing items, please contact your dealer. The SPI-8450-LLVA Industrial Single board computer This User’s Manual One IDE 40pin ribbon cable One IDE 80pin ribbon cable One Floppy ribbon cable One CD-ROM (Driver disks utilities) One mounting bracket attached with 2 serials ports ribbon cable One mounting bracket attached with 1 parallel port ribbon cab
Summary of the content on the page No. 12
CHAPTER 1 – Introduction 1.5 Connector & Jumper Location CN1 JRS2 JRS1 1 1 1 IR1 JRS3 1 1 CN15 CN3 CN10 DIMM2 CN21 CN6 CN9 DIMM1 CN11 CN7 1 CN8 CN12 CPU 1 CN17 CN16 Socket CN13 CN2 CN4 CN5 CN18 CN20 PW2 CN14 FAN1 FAN2 CN19 1 1 JP104 1 JP105 JP106 1 JP107 JBAT1 SPI-8450-LLVA 5
Summary of the content on the page No. 13
DATA DATA CTRL CTRL ADDR ADDR CHAPTER 1 – Introduction 1.6 Block Diagram BLOCK DIAGRAM CLOCK SOCKET 478 Processor ICS950220 P4 PROCESSOR PWM SSOP48 AGTL+ BUS GMCH BROOKDALE-G VGA DDR266 CRT FCBGA760 Modules CONNECTOR PCI TO ISA IDE Primary PCI CNTRL UDMA66/100 Bridge IDE Secondary W83628F PCI ADDR/DATA W83629D USB 2.0 USB PORT ICH4 1-6 BGA421 PCI CNTRL LAN LAN PCI ADDR/DATA Connector PCI CNTRL PCI CNTRL RAID IDE GIGA LAN CONTROLLER Connector PCI ADDR/DATA PCI ADDR/DATA AC'97 LINK AC'97 Firm
Summary of the content on the page No. 14
CHAPTER 2 –Hardware Installations Chapter 2 Hardware Installations This chapter provides information on how to use the jumpers and connectors on the SPI-8450-LLVA in order to set up a workable system. 2.1 Installation procedure (1) Confirm the power supply is off. (2) Install the processor with correct orientation. (3) Insert the DRAM module with correct orientation. (4) Mount the Fan on the top of the processor and connect it to FAN connector. (5) Insert all external cables except for flat pane
Summary of the content on the page No. 15
CHAPTER 2 –Hardware Installations 2.2 CPU Installation: The SPI-8450-LLVA Industrial CPU Card supports a single Intel 478pin FC-PGA2 type Pentium 4 or Celeron processor. The processor’s VID pins automatically program the voltage regulator on the CPU card to the required processor voltage. The host bus speed is automatically selected. The processor connects to the CPU card through the 478-pins socket. The CPU card supports the processors listed in table below: Celeron processor Host Bus frequency
Summary of the content on the page No. 16
CHAPTER 2 –Hardware Installations 2.3 Main Memory Installation: DIMM1/2 The SPI-8450-LLVA Industrial CPU Card supports two single-side or double-sided DDR200(PC1600)/266(PC2100) unregistered, Two 184-pin DIMM sockets for a maximum total memory of 2GB. Using the non-ECC DDR SDRAM DIMMS. The CPU card supports the following memory features: 2.5V(only) 184-pin DIMMs with gold-plated contacts 200 MHz (PC1600)/266 MHz (PC2100) DDR SDRAM Non-ECC DIMMs Unbuffered, unregistered single-sided or double
Summary of the content on the page No. 17
CHAPTER 2 –Hardware Installations 2.4 Front Panel Connector: CN1 This header can be connected to a front panel power switch. The front panel connector includes headers for these I/O connections: Power switch This header can be connected the power on switch when ATX power supply use. Power LED This header can be connected to an LED that will light when the computer is powered on. Hard drive activity LED This header can be connected to an LED to provide a visual indicator that data is being read f
Summary of the content on the page No. 18
CHAPTER 2 –Hardware Installations 2.5 USB Connector: CN2/ CN4/ CN5 This board have three USB(v2.0 compliant) pin-header connectors. This header is for the optional USB cable to provide each two USB ports. (Up to six USB ports) PIN No. Function PIN No. Function 1 VCC1 2 VCC2 CN2,4,5 1 2 3 USBP1- 4 USBP2- 3 4 5 6 5 USBP1+ 6 USBP2+ 7 8 9 10 7 GND 8 GND 9 No Connect 10 Chassis GND Optional USB Cable (It is necessary to each connector) Model: USB Co
Summary of the content on the page No. 19
CHAPTER 2 –Hardware Installations 2.6 Parallel Port Connector: CN3 The parallel port bracket can used to add an additional parallel port for additional parallel devices. There are four options for parallel port operation: Compatible (Standard mode) Bi-Directional (PS/2 compatible) Bi-Directional EPP. A driver from the peripheral manufacturer is required for operation. Bi-Directional High-speed ECP PIN No. Function PIN No. Function 1 STROBE 2 ALF CN3 3 PD0 4 ERROR 1 2 5
Summary of the content on the page No. 20
CHAPTER 2 –Hardware Installations 2.7 Serial Port connector: CN6 /CN9 COM1(CN6) and COM2(CN9) are use in the 10-pins box-headers, are onboard serial ports of the CPU card SPI-8450-LLVA. The following table shows the pin assignments of these connectors. PIN No. RS-232C RS-422* RS-485* CN6,CN9 1 DCD TX- TX- CN6,9 2 RXD TX+ TX+ 1 6 3 TSD RX+ RX+ 4 DTR RX- RX- 5 GND GND GND 5 10 6 DST RTS- N.C 7 RTS RTS+ N.C 8 CTS CTS+ N.C 9 RI CTS- N.C 10 N.C N.C N.C * RS-422/485 assigned f
