Summary of the content on the page No. 1
REJ10J1775-0100
SH7137 Group PLQP0100KB-A
User System Interface Board
R0E571370CFK00 User’s Manual
Renesas Microcomputer Development Environment System
SuperH ™ Family / SH7137 Series
Rev.1.00
Revision Date: Jan. 09, 2008
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Notes regarding these materials 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this do
Summary of the content on the page No. 4
Summary of the content on the page No. 5
IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this emulator product. � KEEP the user's manual handy for future reference. Do not attempt to use the emulator product until you fully understand its mechanism. Emulator Product: Throughout this document, the term "emulator product" shall be defined as the following products produced only by Renesas Technology Corp. and Renesas Solutions Corp. excluding all subsidiary products. • E200F main unit • External bus
Summary of the content on the page No. 6
Target User of the Emulator Product: This emulator product should only be used by those who have carefully read and thoroughly understood the information and restrictions contained in the user's manual. Do not attempt to use the emulator product until you fully understand its mechanism. It is highly recommended that first-time users be instructed by users that are well versed in the operation of the emulator product. Users are required to be familiar with the basic knowledg
Summary of the content on the page No. 7
LIMITED WARRANTY Renesas warrants its emulator products to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas, at its option, will replace any emulator products returned intact to the factory, transportation charges prepaid, which Renesas, upon inspection, shall determine to be defective in material and/or workmanship. The foregoing shall constitute the sole remedy for any breach of Renesas’ warrant
Summary of the content on the page No. 8
State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which may vary from state to state. The Warranty is Void in the Following Cases: Renesas shall have no liability or legal responsibility for any problems caused by misuse, abuse, misapplication, neglect,
Summary of the content on the page No. 9
SAFETY PAGE READ FIRST � READ this user's manual before using this emulator product. � KEEP the user's manual handy for future reference. Do not attempt to use the emulator product until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS Either in the user's manual or on the product, several icons are used to insure proper handling of this product and also to prevent injuries to you or other persons, or damage to your properties. Their graphic images and meanings are given in
Summary of the content on the page No. 10
means WARNING or CAUTION. Example: CAUTION AGAINST AN ELECTRIC SHOCK means PROHIBITION. Example: DISASSEMBLY PROHIBITED means A FORCIBLE ACTION. Example: UNPLUG THE POWER CABLE FROM THE RECEPTACLE. VI
Summary of the content on the page No. 11
WARNING Warnings for AC Power Supply: • If the attached AC power cable does not fit the receptacle, do not alter the AC power cable and do not plug it forcibly. Failure to comply may cause electric shock and/or fire. • Use an AC power cable which complies with the safety standard of the country. • Do not touch the plug of the AC power cable when your hands are wet. This may cause electric shock. • This product is connected signal ground with frame ground. If your develo
Summary of the content on the page No. 12
WARNING • If you smell a strange odor, hear an unusual sound, or see smoke coming from this product, then disconnect power immediately by unplugging the AC power cable from the outlet. Do not use this as it is because of the danger of electric shock and/or fire. In this case, contact your local distributor. • When installing or connecting this product with other equipment, shut down AC power or disconnect the AC power cord from the equipment to prevent personal in
Summary of the content on the page No. 13
CAUTION Cautions for AC Adapter: • Use only the AC adapter included in this product package. • The included AC adapter is for this emulator. Do not use it for other product. • The DC plug on the included AC adapter has the below polarity. • The included AC adapter has no power supply switch. The AC adapter is always active while connecting the AC power cable. Cautions to Be Taken for This Product: • Use caution when handling this product. Be careful not to apply a
Summary of the content on the page No. 14
WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance. 2. Always switch OFF the E200F emulator and user system before connecting or disconnecting any CABLES or PARTS. 3. Always before c
Summary of the content on the page No. 15
Preface The R0E571370CFK00 is a user system interface board that connects a user system for the SH7137 PLQP0100KB-A (former package: FP-100UV) package to the SH7147 E200F emulator (R0E0200F1EMU00 or R0E571470VKK00). i
Summary of the content on the page No. 16
Contents Section 1 Configuration.....................................................................................1 Section 2 Environmental Conditions.................................................................3 Section 3 User Interface Specifications.............................................................4 Section 4 Connection Procedures......................................................................6 4.1 Connecting User System Interface Board to User System.....
Summary of the content on the page No. 17
Section 1 Configuration Figure 1 and table 1 show the external appearance and components, respectively, of the user system interface board for the PLQP0100KB-A. Please make sure you have all of these components when unpacking. Screws (M2.0 x 6 mm) EV-chip unit Screws (M2.0 x 10 mm) Board Socket cover IC socket User system Figure 1 User System Interface Board for the SH7137 PLQP0100KB-A Package 1 Spacer
Summary of the content on the page No. 18
CAUTION Use a NQPACK100SD-ND socket (manufactured by Tokyo Eletech Corporation) and a HQPACK100SD (manufactured by Tokyo Eletech Corporation) for the PLQP0100KB-A package IC socket and socket cover, respectively, on the user system. Table 1 R0E571370CFK00 Components No. Component Quantity Remarks 1 Board 1 With four spacers (2.6MP x 11 mm) 2 IC socket 1 For the PLQP0100KB-A package (to be mounted on the user system) 3 Socket cover 1 For the PLQP0100KB-A package (for installing MCU)
Summary of the content on the page No. 19
Section 2 Environmental Conditions Maintain the conditions in table 2 when using the emulator. Table 2 Environmental Conditions Item Specifications Temperature Operating: +10 to +35°C Storage: -10 to +35°C Humidity Operating: 35 to 80% RH, no condensation Storage: 35 to 80% RH, no condensation 2 Vibration Operating: 2.45 m/s max. 2 Storage: 4.9 m/s max. 2 Transportation: 14.7 m/s max. Ambient gases There must be no corrosive gases present. 3
Summary of the content on the page No. 20
Section 3 User Interface Specifications This user system interface board has the function that masks the chip select signals (CS0 and CS1), bus request signal (BREQ), and wait input signal (WAIT) depending on the setting of a switch. To use the mask function, set the switch (SW1) on the user system interface board (figure 2), according to table 3, and mask pins. Note: When the emulation memory function is used, the output of the chip select signals to the user system is controlled. Be s
