Summary of the content on the page No. 1
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Thank You! Thank you for choosing Humminbird®, America's #1 name in fishfinders. Humminbird® has built its reputation by designing and manufacturing top-quality, thoroughly reliable marine equipment. Your Humminbird® is designed for trouble-free use in even the harshest marine environment. In the unlikely event that your Humminbird® does require repairs, we offer an exclusive Service Policy - free of charge during the first year after purchase, and available at a reasonable rate after the one-ye
Summary of the content on the page No. 4
Table of Contents 1100 Series™ Introduction 1 How GPS and Cartography Work 1 MMC/SD Slot 2 Software Updates ........................................................................................................................................ 3 Accessory Bus 3 Video and GPS Output Connectors ............................................................................................................ 3 Installation Overview 4 Control Head Installation 6 Gimbal Mounting the Control Head..........
Summary of the content on the page No. 5
Table of Contents Views 28 Views and Readouts .................................................................................................................................. 28 Bird’s Eye No Readouts View.................................................................................................................... 29 Bird’s Eye View .......................................................................................................................................... 31 Chart/Bird's Ey
Summary of the content on the page No. 6
Table of Contents Cursor to Waypoint (Chart or Combo view only) ........................................................................................ 69 Save Current Track .................................................................................................................................... 69 Clear Current Track .................................................................................................................................... 70 Save Current Route (only when n
Summary of the content on the page No. 7
Table of Contents Chart Menu Tab 89 Chart Detail Level ...................................................................................................................................... 90 Map Borders .............................................................................................................................................. 90 Lat/Lon Grid ........................................................................................................................................
Summary of the content on the page No. 8
Table of Contents Date Format (Advanced, International only).............................................................................................. 104 Digits Format (Advanced) ........................................................................................................................ 104 NMEA Output (Advanced) ...................................................................................................................... 104 Demonstration.............................
Summary of the content on the page No. 9
1100 Series™ Introduction Your 1100 Series™ Chartplotter comes in the following configuration: • Humminbird® 1155c Chartplotter: Networkable GPS Chartplotting System, GPS Receiver included. How GPS and Cartography Work Your 1100 Series™ Chartplotter supports GPS and chartplotting, and uses GPS to determine your position and display it on a grid. The Global Positioning System (GPS) is a satellite navigation system designed and maintained by the U.S. Department of Defense. GPS was originally inten
Summary of the content on the page No. 10
The GPS Receiver included with your 1100 Series™ Chartplotter allows you to combine easy-to-use chartplotter and navigation capabilities. The following GPS functionality is currently supported by the 1100 Series™ Chartplotter when it is connected to the included GPS receiver: • View current position • View current track (breadcrumb trail) • View precision speed and heading from your GPS receiver • Save tracks, waypoints and routes • Travel a route and navigate from one waypoint to the next. You
Summary of the content on the page No. 11
Software Updates Use the MMC/SD slot to update the software version of your control head. To update the software in your control head, plug in the appropriate MMC/SD card that contains a software update file; the unit will recognize it, will tell you what software version your control head is currently running, and will ask you if you want to update the software in the unit to match that on the MMC/SD card. You can obtain software updates from the www.humminbird.com website. Accessory Bus Use th
Summary of the content on the page No. 12
Installation Overview Please read all instructions that are relevant for your configuration before beginning the installation process. NOTE: Installation procedures will depend on product configuration. The 1100 Series™ has a wide variety of configurations. 2 1 7 8 5 3 6 4 Accessory Bus 5 1 Optional “Y” Cable GPS Receiver 6 2 Power WeatherSense® 7 3 Temperature Video Signal 8 4 Speed through water GPS Out 9 4
Summary of the content on the page No. 13
1100 Series™ Connectors 1 GPS Out 2 Power 3 Communications 1 2 3 4 Video Out 5 Temp/Speed 5 6 4 6 Not Used Inside the boat there is often a channel or conduit used for other wiring, this can be used to route cables. Be sure to route the cables as far as practical from the antenna cable of VHF radios or tachometer cables to reduce the possibility of interference. The GPS receiver cable should not be cut, and care should be used not to damage the cable insulation. Basic installation tasks that you
Summary of the content on the page No. 14
Control Head Installation You have two choices for mounting your 1100 Series™ control head, Gimbal mounting, where you use a surface on the boat, such as the dash, to mount the control head so that it can be tilted up or down, or In- dash mounting. Gimbal Mounting the Control Head If you are gimbal mounting the Humminbird® 1100 Series™, you can pre-assemble the unit in order to plan the best mounting location. 1 Washer 2 Gimbal Knob 1 3 Gimbal Mounting Bracket 2 3 In addition to the hardware su
Summary of the content on the page No. 15
NOTE: When drilling holes in fiberglass hulls, it is best to start with a smaller bit and use progressively larger drill bits to reduce the chance of chipping or flaking the outer coating. Fill all holes with marine grade silicone sealant. NOTE: You must have underside access to the mounting location to pass the cables through to the surface. Also, make sure that the mounting surface is adequately supported to protect the control head from excessive wave shock and vibration and provide visibilit
Summary of the content on the page No. 16
6a. If the cables must pass through a hole directly beneath the mounting bracket, mark and drill an additional 1" (25 mm) hole centered between the four mounting holes. Route the cables through the 1" hole. Place the gimbal over the mounting surface hole, then use it to mark the position of the two mounting screws, closest to the center large hole. Remove the gimbal and drill the two mounting holes using a 9/64" (3.5 mm) bit. Do not install the hole cover at this time. or... 6b. If the cables
Summary of the content on the page No. 17
Cables Routed Behind Mounting Bracket 1 Gimbal Mounting Bracket 2 Grommet 3 Hole Cover 3 1 2 9. Thread the cables through the opening in the back of the cable collector cover. 10. Insert cable connectors into the proper recesses on the cable collector insert. The cable connectors are keyed to prevent reverse installation, so be careful not to force the connectors into the wrong slots. If you don’t have a cable for every hole in the insert, install the blank plugs to protect the control head from
Summary of the content on the page No. 18
Assembling the Cable Collector 1 Cable Collector Insert 2 Screws 3 Cable Collector Cover 1 2 3 12. Attach the cable collector insert to the cable collector cover using the (2) #6 Phillips screws provided. 13. Place the control head back onto the mounting bracket. Plug the assembled cable collector into the back of the control head, pushing gently but steadily until you feel the collector snap into place. Cable connectors and cable sockets are keyed to prevent reverse installation, so be careful
Summary of the content on the page No. 19
In-Dash Mounting the Control Head If you are in-dash mounting the control head, start by placing the components on the surfaces where you intend to install them before installation. Make sure that the surfaces you have chosen provide adequate protection from wave shock, and that all cables can reach the control head. NOTE: If a cable is too short for your application, extension cables are available. Call Humminbird® Customer Support at 1-800-633-1468 for more information. Parts and tools specifi
Summary of the content on the page No. 20
5. Insert the control head through the mounting hole from the front side of the dash. Place a washer, lock washer, and wing nut onto each threaded rod and tighten fully. 6. Thread the cables through the opening in the back of the cable collector cover. 7. Insert cable connectors into the proper recesses on the cable collector insert. The cable connectors are keyed to prevent reverse installation, so be careful not to force the connectors into the wrong slots. If you don’t have a cable for every
