Summary of the content on the page No. 5
European Union only EN Dear Customer, EMC Supplement This equipment is in conformity with the provisions and protection This apparatus is in conformance with the valid European directives and requirements of the corresponding European Directives. This standards regarding electromagnetic compatibility and electrical safety. equipment is designed for professional video appliances and can be European representative of Victor Company of Japan, Limited is: used in the following environments: JVC
Summary of the content on the page No. 6
Installation CAUTION • Do not rest your arm on the monitor or lean against the monitor. • Do not touch the LCD panel when installing the monitor. • Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor or injury. To install the monitor on a shelf or any other 4 Adjust the position so that the screw holes on the stand support align with right and left screw holes “C” and “E” on the bottom suitable surface using screws plate, tigh
Summary of the content on the page No. 7
1 Lay the monitor on a cloth with the LCD panel facing down to To install the monitor on a wall prevent the LCD panel from being damaged. Loosen the stand You can install the monitor on a wall by changing how the stand EN screws on the stand support and remove the bottom plate. bottom plate is attached. Installation Only for Authorized Service Personnel Consult authorized service personnel for the installation of Bottom plate this unit. Installation instructions must be followed precisely in
Summary of the content on the page No. 8
Connections Rear panel DT-R24L4D DT-R17L4D The illustration of the monitor is of DT-R24L4D. DT-R24L4D DT-R17L4D Security slot Attach a security wire to this slot. 1 POWER switch Turns AC power on or off. • You need to press button (☞ t on page 10) to use the monitor after turning on the POWER switch. 2 AC IN terminal AC power input connector. Connect the provided AC power cord to an AC outlet. • Attach the provided power cord holder to prevent accidental disconnection of the AC power cord (☞
Summary of the content on the page No. 9
6 For DT-R24L4D: AUDIO ASSIGN (MONITOR OUT) terminals (pin jack) / For DT-R17L4D: AUDIO (MONITOR OUT) terminals (pin jack) Output terminals for the analog audio signal. EN • For DT-R24L4D: The terminals output the audio signal through AUDIO ASSIGN (IN 1 or IN 2) terminals when you select the video input you have selected for “AUDIO1 ASSIGN.” or “AUDIO2 ASSIGN.” in “AUDIO SETTING” (☞ page 14). • For DT-R17L4D: The terminals emit the audio signals through the AUDIO (IN) terminal or EMBEDDED AUDIO
Summary of the content on the page No. 10
Daily Operations Front panel Tally lamp This lamp is controlled by the tally function of the MAKE/TRIGGER terminal. • You can select the color of the tally lamp from “GREEN” or “RED.” (☞ “TALLY SELECT” in “FUNCTION SETTING” on page 15 and “External Control” on page 18) • “NO EFFECT” is displayed when you press a button which is not available for the current input or signal format (the lamp lights even when the function does not actually work). • The items controlled by the MAKE system cann
Summary of the content on the page No. 11
Audio Channel Selection EN Select audio channels emitted from the speakers (L/R) and the Press buttons to select the left (L ch) or 2 AUDIO ASSIGN (DT-R24L4D) / AUDIO (DT-R17L4D) (MONITOR right (R ch). OUT) (OUT1(L)/OUT2(R)) terminals, when EMBEDDED AUDIO signals come in to the E. AUDIO HD/SD SDI terminal (IN1 or IN2) Press buttons to select an audio channel. 3 and SDI input (1 or 2) is selected. • Each time you press the button, the audio channel changes • You have to choose a group
Summary of the content on the page No. 12
Menu Confi guration The operation procedure MAIN MENU SET-UP MENU Display the menu. 1 Selected To display the MAIN MENU item Press MENU button. To display the SET-UP MENU Press button while holding button. Operation guide Press buttons to select an item, then press button. 2 Ex.: When “MARKER” in the MAIN • For some items, adjustments will be made by pressing . MENU is selected Press buttons to select an item, then press buttons to make adjustments. 3 Press MENU button to fi ni
Summary of the content on the page No. 13
MAIN MENU EN PICTURE FUNCTION Setting for the picture quality Item To do Setting value *1 APERTURE Activates/deactivates the function at the level set in “APERTURE LEVEL.” OFF, ON *1 APERTURE LEVEL Compensate the frequency response of the luminance signal of the video signal. 01 – 10 CTI Adjust the clearness of the outlines of the chrominance signal. OFF, NORMAL, HARD LTI Adjust the clearness of the outlines of the luminance signal. OFF, NORMAL, HARD I/P MODE Selects a proper mode corresponding
Summary of the content on the page No. 14
Menu Confi guration (cont.) *1*2 MARKER Settings for marker functions 2/2 Item To do Setting value *3 *4 R-AREA MARKER Activate/deactivate the area marker and select the style of it. OFF, LINE, HALF, HALF+L, BLK. , BLK.+L *3 R-MARKER ASPECT Select the aspect ratio of the area marker. 4:3, 14:9, 13:9, 2.35:1, 1.85:1, 1.66:1 *4 R-SAFETY MARKER Activate/deactivate the safety marker and select the style of it. OFF, LINE, HALF, HALF+L, BLK. , BLK.+L R-SAFETY AREA Adjust the area of the safety marke
Summary of the content on the page No. 15
SYNC FUNCTION EN Settings for the synchronization with signals Item To do Setting value NO SYNC ACTION Select the screen status when no signal is coming in. OFF, P.SAVE, GRAY B. P.SAVE: power save mode GRAY B.: gray screen DELAY TIME Select the period until the screen status changes as selected in “NO SYNC 30sec., 5min., 15min. ACTION” after signals stop coming in. LOW LATENCY Activates/deactivates the function to shorten the time taken to display the ON, OFF picture (low latency function). • If
Summary of the content on the page No. 16
Menu Confi guration (cont.) SIZE/POSI. ADJ. Adjusts the size and position of the picture. Item To do Setting value *1 H SIZE Adjust the horizontal picture size. Setting value varies depending on *1 the signals. H POSITION Adjust the horizontal picture position. *1 V SIZE Adjust the vertical picture size. *1 V POSITION Adjust the vertical picture position. sub menu Display the sub menu which enables you to adjust the items of “SIZE/POSI. ADJ.” while viewing the actual picture. reset Restore the d
Summary of the content on the page No. 17
INFORMATION EN Settings for the information display of the monitor Item To do Setting value POSITION UPPER, LOWER Select the position to show the information display (☞ “On the Information Display” on page 11). SOURCE ID Select whether the name assigned in “CHARACTER SET.” is displayed on the OFF, ON, AUTO screen (☞ “On the Information Display” on page 11). • When “AUTO” is selected, the display color synchronizes with the color of the tally lamp while the tally lamp is lit. *1 CHARACTER SET.
Summary of the content on the page No. 18
External Control About the external control Using the MAKE/TRIGGER system This monitor has three external control terminals. The MAKE/TRIGGER terminal is confi gured as follows. You can assign a function to each pin terminal in “REMOTE SETTING” (☞ “PIN1, PIN2, • MAKE/TRIGGER terminal (RJ-45): The following external control PIN3, PIN4, PIN5” in “PARALLEL TYPE” on page 16). systems are available. • You cannot change the functions assigned to the pin terminals from (1) MAKE (make contact) syst
Summary of the content on the page No. 19
Display Functions to be controlled Opening Short-circuiting EN TALLY SEL Selects the color of the tally lamp. Green Red SDI 1 Changes the input to “SDI 1.” Invalid Valid SDI 2 Changes the input to “SDI 2.” Invalid Valid DVI Changes the input to “DVI.” Invalid Valid VIDEO 1 Changes the input to “VIDEO 1.” Invalid Valid DT-R24L4D VIDEO 2 Changes the input to “VIDEO 2.” Invalid Valid DT-R17L4D VIDEO Changes the input to “VIDEO.” Invalid Valid A.MARK
Summary of the content on the page No. 20
External Control (cont.) Using the serial communication You can control the monitor from a personal computer etc. via the RS-485 or RS-232C terminal. • Consult your dealer for the details of the external control specifi cation. Terminal Input terminal Cable Communication specifi cations specifi cation RS-485 A straight LAN cable Baud Rate: 4800 bps RS-232C A straight cable with a D-sub 9-pin connector (male Data Bits: 8 bits for the monitor, female for the personal
Summary of the content on the page No. 1
EN
The lightning flash with arrowhead
symbol, within an equilateral triangle is
CAUTION
intended to alert the user to the presence
of uninsulated “dangerous voltage”
RISK OF ELECTRICAL SHOCK
within the product’s enclosure that may
DO NOT OPEN
be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an
To reduce the risk of electric shock. Do
CAUTION:
equilateral triangle is intended to alert
not remove cover (or back). No user
the use
Summary of the content on the page No. 2
Table of Contents Safety Precautions 3 IMPORTANT SAFEGUARDS ............................................................................... 3 Caution for use of the product for many hours...................................................... 5 Caution for use of the product in the high temperature ........................................ 5 Maintenance ......................................................................................................... 5 Installation 6 Connections 8 Rear pane
Summary of the content on the page No. 3
Safety Precautions WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, Under the following conditions, DO NOT EXPOSE THIS APPARATUS TO RAIN OR 1. Turn off the power. EN MOISTURE. NO OBJECTS FILLED WITH LIQUIDS, SUCH 2. Unplug this product from the wall outlet. AS VASES, SHALL BE PLACED ON THE APPARATUS. 3. Refer service to qualifi ed service personnel. IMPORTANT SAFEGUARDS a) When the product emits smoke or unusual smell. b) When the product exhibits a distinct change in performance Electrical
Summary of the content on the page No. 4
Safety Precautions (cont.) • Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the product and protect it from overheating. These openings must not be blocked or covered. • Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-circuit the parts, which could result in a fi re or electric shock. • Never spill liquid of any kind on the product. • Never place anything on the product. (Pl
