Summary of the content on the page No. 1
SyncMaster 731BA / 931BA
Install drivers Install programs
Summary of the content on the page No. 2
Notation Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode.. The images here are for reference only, and are not applicable
Summary of the content on the page No. 3
Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. A bad connection may cause fire. Do not bend the plug excessively and wire nor place heavy objects upon them, which could cause damage. This may cause electric shock or fire.
Summary of the content on the page No. 4
Installation Be sure to contact an authorized Service Center, when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. Failure to do so may cause serious damage to your set. Place your monitor in a location with low humidity and a minimum of dust. Failure to do so may cause electric shock or fire inside the monitor. Do no
Summary of the content on the page No. 5
Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc. Any increase in the internal temperature may cause fire. Put down the monitor carefully. Failing to do so may damage the monitor. Do not place the monitor face down. This may damage the TFT-LCD surface. The installation of the bracket must be done by a qualified professional. Installing the bracket by unqualified personnel may result in injury. Always use the mo
Summary of the content on the page No. 6
Do not spray water or detergent directly onto the monitor. This may cause damage, electric shock or fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. A dirty connector may cause electric shock or fire. Make sure to unplug the power cord before cleaning the product. Otherwise, this may cause electric shock or fire. Unplug the power cord from the power ou
Summary of the content on the page No. 7
If your monitor does not operate normally - in particular, if there are any unusual sound or smell coming from it - unplug it immediately and the Service Center. This may cause electric shock or fire. Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. This may cause a malfunction, electric shock or fire. In particular, avoid operating the monitor near water or outdoors where it could be exposed to snow or rain. If the mon
Summary of the content on the page No. 8
This may cause an explosion or fire. Never insert anything metallic into the monitor openings. This may cause electric shock, fire or injury. Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc. This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact
Summary of the content on the page No. 9
Failure to disconnect cables may damage it and cause fire or electric shock. Place the product out of children's reach, as they could damage by hanging onto it. A falling product may cause injury to the person or even fatality. When not using the product for an extended period of time, keep the product unplugged. Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire. Do not place your children's favorite
Summary of the content on the page No. 10
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local governmen
Summary of the content on the page No. 11
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have an image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate a correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty. What is Image retention ? During normal operation of a LCD panel, pix
Summary of the content on the page No. 12
Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a
Summary of the content on the page No. 13
Features Anion Monitor The anion generator emits up to 50,000 anions. The anion monitor emits up to 50,000 anions, which is equal to the number of anions emitted by 40 sanseverias, which generate the most anions among plants. LED (Operating Light) Anion Emission Hole Anion Off/On Selecting 'Off/On' Anion is possible through the OSD. Checking the Anion The anion emission status can be seen through the LED (Operating Light) of Operation the anion generator. Package Contents Pl
Summary of the content on the page No. 14
Monitor With Stand Monitor & Simple stand Manual Warranty Card User's Guide, Monitor Driver, Quick Setup Guide (Not available in all Natural Color software, locations) MagicTune™ software Cable Dedicated Anion Cleaning Power Cord D-sub Cable Brush Sold separately DVI Cable Your Monitor Front
Summary of the content on the page No. 15
MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MagicBright™ button MagicBright™ is a new feature providing optimum viewing [] environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre- configured brightness value. You can easily select one of six settings by simply pressing MagicBright™ control button.
Summary of the content on the page No. 16
Enter button [ ] / Activates a highlighted menu item. / SOURCE button Push the 'SOURCE', then selects the video signal while the OSD is off. (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal.) If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable. AUTO button Use this button for auto adjustment. >> Click h
Summary of the content on the page No. 17
Connecting Cables Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the D-sub (Analog) connector on the video card. - Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [RGB IN] Using the DVI (Digital) connector on the video card. - Connect the DVI Cable to the DVI Port on the back of your Monitor.
Summary of the content on the page No. 18
Monitor Assembly This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad. Attaching a Base A. Monitor B. Mounting interface pad (Sold separately) Turn off your monitor and unplug its power cord. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. Remove three screws and then remove the stand from the LCD monitor. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it with
Summary of the content on the page No. 19
Monitor Driver When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown below. Internet web site :http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/moni
Summary of the content on the page No. 20
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ Monitor driver installation is completed. Installing the Monitor Driver (Manual) Windows XP | Windows 2000 | Windows ME | Windows NT | Linux ® ® Microsoft Windows XP Operating System Insert the CD into the CD-ROM drive. Click "Start" → "Control Panel" then click the "Appearance and T
