Summary of the content on the page No. 1
15 ” / 17 ” / 19 ” TFT-LCD MONITOR
WITH
VIDEO INPUTS
V151/ V172/ V191 Video Series
USER ’ S MANUAL
www.viewera.com
Rev. 1.0
Summary of the content on the page No. 2
CONTENTS 1. Introduction Page 2 Product Description ....................................................... Page 2 Package Contents .......................................................... Page 2 Product Features …....................................................... Page 2 Screen Cleaning Techniques ......................................... Page 3 Additional ..................................................................... Page 3 2. Control Functions Page 5 Function Select
Summary of the content on the page No. 3
1. Introduction Product Description Congratulations on your purchase of the ViewEra V151/ V172/ V191 video series LCD monitor. It incorporates high quality display into a small light-weighted module. It has power-saving capabilities and emits no radiation. You will certainly benefit from this monitor in lots of ways; to name some of them: comfort, safety, space-saving and environmental protection. These LCD monitors incorporates 15 ” / 17 ” / 19 ” color active matrix thin-film-transis
Summary of the content on the page No. 4
Screen Cleaning Techniques 1. Gently clean the screen with a clean camel hair lens brush, or a soft, clean, lint-free cloth, to remove dust and other particles that can scratch the screen. 2. Do not apply pressure to the screen surface when wiping it clean. 3. Do not pour or spray any liquid directly onto the screen or casing. Chemical cleaners have been reported to damage the screen or case of the LCD monitor. Additional Read all of these instructions and save them for later use.
Summary of the content on the page No. 5
If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician. If the product exhibits a distinct change in performance, service may be required. 4. Power and extension cords Do not allow anything to rest on the power cord. Do not locate this product where p
Summary of the content on the page No. 6
2. Control Functions The monitor digital control functions are located on the front panel. They are shown in the figure below and described in the following paragraphs. 1. Power switch with indicator LED 2. Function keys Function Selection 1. Press the knob “ 1 ” to show the OSD menu. Then use the “ △ ” and “ ▽” to select a function. Press the knob “ 2 ” to close the OSD menu. 2. With the knob “ △ ” and “ ▽ ” , you can adjust the speaker volume on the monitor. When you press th
Summary of the content on the page No. 7
2. Video Brightness - Adjust the luminance level of the image. Contrast - Adjust the difference in luminance between light and dark areas of the image. Black Level - Adjust the black level of the image. Exit - Close the video OSD menu. 3. Audio Volume - Adjust the speaker volume Exit - Exit the audio OSD menu. Note: You can press “ 1 ” button repeatedly to mute or enable the monitor speakers. 4. Color Color Temperature User - Adjust the R.G.B. gain level.
Summary of the content on the page No. 8
5. Image Auto Tune - Adjust geometry of the image automatically. H. Width - Adjust the horizontal sync size of signal. H. Phase - Adjust the horizontal sync phase of signal. H. Position - Adjust the horizontal position of the image. V. Position - Adjust the vertical position of the image. Exit - Close the Image OSD menu. Note: Image function is only available for VGA and Video signal input. 6. Language - Set the language of the OSD windows. 7. Tools OSD Control OSD Timer
Summary of the content on the page No. 9
3. Installation Unpacking Open the shipping carton and check the package contents. If any items are missing or damaged, contact us immediately. The package should include the following items: - 15” / 17 ” / 19 ” TFT-LCD monitor -Power cord -AC/DC power adapter -VGA cable -Audio cable -User's manual Installing the Base Follow these steps to install the base: 1. Turn the monitor down. 2. Assembly the base to the arm with screw. 3. Tighten the screw with a coin. I
Summary of the content on the page No. 10
4. Display Modes Micro-controller Features The micro-controller automatically detects the video board installed in your system. When you turn on the monitor, the micro-controller checks the display mode memory stored in the user setting area of the video board, and then the factory presetting area. It then adjusts to the proper display mode. The micro-controller has the memory capacity to store different display modes, including timing formats and display-settings. This memory capacity i
Summary of the content on the page No. 11
MODE Resolution Horizontal Vertical Remark (Dots*lines) Freq.(KHz) Freq.(Hz) 1. VGA 640×350 31.5 70 Non-interlaced 2. VGA 720×400 31.5 70 Non-interlaced 3. VGA 640×480 31.5 60 Non-interlaced 4. VESA/75 640×480 37.5 75 Non-interlaced 5. VESA/60 800×600 37.9 60 Non-interlaced 6. VESA/75 800×600 46.9 75 Non-interlaced 7. VESA/60 1024×768 48.4 60 Non-interlaced 8. VESA/70 1024×768 56.5 70 Non-interlaced 9. VESA/75 1024×768 60.0 75 Non-interlaced 10. VESA/60 1280×1024 64.0 60 Non-i
Summary of the content on the page No. 12
6. Power Saving Features When the power saving is active, the power indicator LED will be from Green Light to Amber. The power saving feature complies with these VESA power saving modes: Power Mode H. Sync. V. Sync. LED Consumption Normal On On Green < 50 Watts Stand-by Off On Amber < 15 Watts Suspend On Off Amber < 15 Watts Off Off Off Amber < 5 Watts The monitor uses the H. Sync and V. Sync signals to determine the operation mode to enter. The monitor power-saving feature auto
Summary of the content on the page No. 13
7. Product Specifications 7.1 V151 series product specifications Model V151 Series Features Panel Type: Active TFT-LCD Screen Size: 15” diagonal Pixel Pitch: 0.297 (W) x 0.297 (H) mm Brightness: Typical: 250 cd/㎡ (Min: 250) Contrast Ratio: Typical: 500:1 (Min: 400:1) Response Time: Typical: 16 ms (Max.:25) Viewing Angle(H / V) Typical: 140° / 120° (Min: 140° / 120°) Max. Resolution: 1024 (W) x 768 (H) Display Color 16.7 M Video Input Analog:15-pin, D-s
Summary of the content on the page No. 14
7.2 V172 series product specifications Model Features V172 Series Panel Type: Active TFT-LCD Screen Size: 17” diagonal Pixel Pitch: 0.264 (W) x 0.264 (H) mm Brightness: Typical: 300 cd/㎡ (Min: 250) Contrast Ratio: Typical: 500:1 (Min: 400:1) Response Time: Typical: 12 ms (Max: 16) Viewing Angle(H / V) Typical: 140° / 130° (Min: 140° / 130°) Max. Resolution: 1280 (W) x 1024 (H) Display Color 16.7 M Video Input Analog:15-pin, D-sub connector S-video x
Summary of the content on the page No. 15
7.3 V191 series product specifications Model Features V191 Series Panel Type: Active TFT-LCD Size: 19” diagonal Pixel Pitch: 0.294 (W) ×0.294 (H) mm Brightness: Typical: 250 cd/㎡ (Min: 250) Contrast Ratio: Typical: 800:1 (Min: 500:1) Response Time: Typical: 8 ms (Max: 16) Viewing Angle(H / V) Typical: 170°/170° (Min: 140° / 140°) Max. Resolution: 1280 (W) x 1024 (H) Display Color 16.7M Video Input Analog:15-pin, D-sub connector S-video x1, RCA compos
Summary of the content on the page No. 16
8. Dead Pixel Policy Dead pixels on the TFT LCD panel are sometimes inevitable. ViewEra guarantees that the monitor will be replaced if the number of dead pixels on our monitor exceeds 5 pixels. 9. Warranty & Customer Service Warranty ViewEra warrants the V151/ V172/ V191 series TFT-LCD monitors for 1 year for LCD panel, for 3 years for parts and labor. For detail information, please refer to our website. (http:// www.viewera.com/warranty.htm) Customer Service Contact your Vie
Summary of the content on the page No. 17
10. Windows setup For the best display quality, please set the monitor type in Windows. Control Panel > Display > Settings > Advanced > List All Modes For 1280 ×1024, please set to “ SXGA 1280 × 1024 @ 60Hz ” 16
Summary of the content on the page No. 18
For 1024 ×768, please set to “ XGA 1024 × 768 @ 60Hz 17
Summary of the content on the page No. 19
11. Trouble Shooting 1) Power on but no picture → Make sure the VGA cable is tightly connected from the video output connector on the video card to the video input connector on the monitor. → Make sure you are using the standard power adapter coming with the monitor. → Check your video card if the driver is correctly installed. If there is no video signal from the video card, “ NO INPUT SIGNAL ” will show on the screen. 2) Wrong or abnormal colors → If any color (red, green, or blue)
Summary of the content on the page No. 20
6) Residue image → If an image remains on the screen for an extended period of time, it may be imprinted in the screen and leave a residue image. It is characteristic of liquid crystal and is not malfunction or deterioration of the liquid crystal. The residue image will disappear after a period of time. It is recommended to set up the screen saver for your LCD monitor. 7) Out of Rang → The first thing you need to check is the screen resolution. Usually “ Out of Range ” is caused by imp
