Summary of the content on the page No. 1
USER'S MANUAL FOR INDUCTION HOBS
cod. 7372 241
Summary of the content on the page No. 2
The built-in induction cooktop is intended for household use only. Materials used Dear customer! for packaging are nature friendly and may be recycled, deposited or destroyed without any threats to the environment. In order to recognize these features, all packing materials are marked with relevant symbols. Once your appliance has become obsolete and you do not intend to use it any longer, take adequate care not to litter the environment. Deposit your old appliance with the auth
Summary of the content on the page No. 3
• The appliance may be built-in and connected to the power supply only by a IMPORTANT WARNINGS qualified technician. • Particular areas of the cooktop surface (adjacent to the hotplates) are hot during operation. Prevent the children to hang around the appliance and warn them properly against the danger of burns. • Hot oil ignites readily, so be sure have the preparation of such food (fries) under constant control. • Hotplates may not be left in operation empty, without an
Summary of the content on the page No. 4
MOUNTING THE BUILT-IN COOKTOP Caution ! • To avoid any possible hazard, the appliance may be installed by qualified personnel only. • Panels and furniture lining of the kitchen cabinet receiving the hob must be treated with temperature resistant adhesives 100°C (otherwise they might be discoloured or deformed because of inadequate temperature resistance). • The cooking hob is intended for building into the worktop above the kitchen element of ≥600 mm depth. After the installation of bu
Summary of the content on the page No. 5
• Worktop must be placed absolutely horizontal. Installation procedure • Suitably protect the edges of the cut aperture. • Connect the cooking hob to the mains power supply (see instructions for the connection of the cooking hob to mains power supply). • Insert the hob into the cut aperture. • Press the hob firmly towards the worktop from above. CONNECTION TO THE POWER SUPPLY • Connections may be carried out by a qualified technician only. The earthing protection mu
Summary of the content on the page No. 6
TECNICAL INFORMATION Type 7372241 Width 590 mm Electrical connection 230-240 V~ or 400-415 V 2N~, 50/60 Hz Working voltage 230-240 V~, 50/60 Hz Type of switch Electronic sensors Cooking zones ( Ø, mm/W ) Forward left 210 , 1500 (P=2000) Rear left 145 , 1200 (P=1600) Rear right 210 , 1500 (P=2000) Forward right 145 , 1200 (P=1600) Total power (W) 2800 P= extra powerful setting Hob surface is completely flat and smooth, without edges to accumulate dirt. Hotplate functio
Summary of the content on the page No. 7
you place smaller dish upon the hotplate and it is recognized, the hotplate will only use the amount of energy required to heat the dish according to its size. Hotplate may be damaged if: • it is turned on and left empty, or an empty dish is placed on it; • you use clay dishes which leave scratches on the ceramic glass surface; • you fail to wipe the dish bottom dry prior placing it on the ceramic glass hotplate; heat induction is obstructed and the hotplate may be damaged; • you fail t
Summary of the content on the page No. 8
INDUCTION COOKTOP 1.Induction hotplate front left 2.Induction hotplate rear left 3.Induction hotplate rear right 4.Induction hotplate front right 5.Hob control panel Hob control elements A. Keys (+ e -) to increase/decrease power level of cooking zone 1 B. Keys (+ e -) to increase/decrease power level of cooking zone 2 C. Keys (+ e -) to increase/decrease power level of cooking zone 3 D. Keys (+ e -) to increase/decrease power level of cooking zone 4 E. Keys (+ e
Summary of the content on the page No. 9
Each burner is complete with its own sensor for detecting the presence of a pan. Pan sensor The system is fine-adjusted to recognize the presence of a pan that, according to the scale of the EN standards, is one size smaller than the nominal diameter of the burner. If the hotplate fails to detect any pan or detects an aluminium pan, power level flashes on its display. After 60 seconds power level backs to 0. If power level flashes on the display when a pan is actually on the hotpla
Summary of the content on the page No. 10
timer can only operate on one heater each time. The heater must always be selected (the display must be viewed “0”) before the time is set; otherwise, the timer will switch off. If we take longer than 10 seconds to select the heater, the timer will switch off. If, after selecting the heater, the time is not defined (T=00) in 5 sec., the timer switches off. When the timer value runs out, the heater associated with the timer switches off. Indication of the heater on tim
Summary of the content on the page No. 11
change the level, the safety mechanism will switch the hotplate off after 10 hours. Protection against overheating Induction cooktop is also fitted with safety device against overheating which protects electronic parts from damages. This device operates on several levels. When cooking zone’s temperature increases excessively, the two-stage fan switches first. If this is not enough, extra powerful heating is deactivated, and finally the safety device either reduces the heating power of c
Summary of the content on the page No. 12
The sequence to set a new Cooktop Power Limit is: Power management for a ▪ During the first 30 seconds after plugging the appliance Limited Power Cooktop ▪ The Touch has to be unlocked and all Heaters Off (ECO) ▪ Push at the same time (A+,A-,D-,D+) keys ▪ Once this is done, a beep sounds and “Po” Characters will be in the timer display and the “actual Cooktop Power Limit” will be in the display 1 and in the display 4. For selecting a new Power Limit: ▪ With any Heater (+ or -
Summary of the content on the page No. 13
Safety functions and error display. ERROR CODE ERROR DESCRIPTION INSTRUCTION MANUAL FA Anomaly of infrared signal, of on/off key - CONTACT AUTHORIZED CENTER all cooking zones are deactivated FOR TECHNICAL ASSISTANCE - SPECIFYING THE ERROR CODE FC Receiver infrared anomaly of button CONTACT AUTHORIZED CENTER on/off - all cooking zones are deactivated FOR TECHNICAL ASSISTANCE - SPECIFYING THE ERROR CODE FE Touch control ntc sensor: short circuit on CONTACT AUTHORIZED CENTER ntc senso
Summary of the content on the page No. 14
zones are deactivated an error is FOR TECHNICAL ASSISTANCE - visualised on all displays SPECIFYING THE ERROR CODE F4 Opening of NTC - all cooking zones are CONTACT AUTHORIZED CENTER deactivated an error is visualised on all FOR TECHNICAL ASSISTANCE - displays SPECIFYING THE ERROR CODE F6 Tension missing on a generator part CONTACT AUTHORIZED CENTER (right or left) - all cooking zones are FOR TECHNICAL ASSISTANCE - deactivated an error is visualised on all SPECIFYING THE ERROR CODE di
Summary of the content on the page No. 15
Foster spa 42041 Brescello (RE) - Italy tel. +39.0522.687425 - tel. Servizio Assistenza +39.0522.684450 fax +39.0522.686019 - fax Servizio Ricambi +39.0522.962166 e-mail: service@fosterspa.com www.fosterspa.com .
