Summary of the content on the page No. 1
Summary of the content on the page No. 2
Important Safety Instructions Before operating this machine, please read the entire manual thoroughly. This unit is designed to be used as surveillance appliance for transporting sounds and images to and from other locations across various interconnects. The manufacturer designed, built, and tested this product for use indoors, using nominal local voltages. Outdoor operation or use of different voltages could damage the unit or peripheral equipment or create a potentially unsafe opera
Summary of the content on the page No. 3
About This Document This manual is intended for administrators and users of NetCam 8001 Network Camera. The manual includes instructions for installing and using the product on your network. Any previous experience of networking will be of use to the reader when installing and using this product. With knowledge of IP networking, router, firewall, UNIX/Linux-based systems would also be greatly helpful for installing and operating the system. Legal Considerations Camera surveillance c
Summary of the content on the page No. 4
Contents The Package Contents .............................................................................................................. 6 1. System Requirements ........................................................................................................... 7 2. Introduction............................................................................................................................ 8 The Benefits..............................................................
Summary of the content on the page No. 5
User List: ................................................................................................................ 34 User Setting:........................................................................................................... 35 Network:...................................................................................................................... 36 IP Assignment ....................................................................................................
Summary of the content on the page No. 6
The Package Contents Thank you for choosing the Asante products. NetCam 8001 is a very competitive Pan Tilt(Digital Zoom) Network Camera system. It is to plug into Ethernet jack with plug-n-play fashion to allow you to delivers clear and sharp image to any browser on the Internet. The NetCam 8001 PT(Z) Internet Camera is provided with the following accessories. Please contact your dealer if any one of the following is missing. Item Descriptions NetCam 8001 Network Camera 1
Summary of the content on the page No. 7
1. System Requirements NetCam 8001/P/W PT(Z) Internet Camera Internet Environments LAN 10/100M Ethernet Wireless LAN 802.11b or 802.11g Monitor System Requirements OS support Windows 2000 Professional SP4, XP Home SP2 Browser support Internet Explorer 6.x or later CPU: Pentium 4 2.4 GHz or later Hardware Memory: 256 MB (512 MB recommended) VGA card resolution: 800 x 600 or higher ©2007 Asante Networks Inc., All rights reserved. NetCam are registered trademarks of Asante Network, In
Summary of the content on the page No. 8
Summary of the content on the page No. 9
Cost effective - NetCam 8001 can deliver quality image/video over prevail broadband IP networks such as DSL/cable or any Ethernet which is majority of worldwide Internet infrastructure. The load or overhead to bring this IP surveillance is very cost effective. There is no additional hardware of software are required. Open System - The NetCam 8001 generates high-quality pictures in standard JPEG, MPEG4 and up coming H.264 format that can be viewed using any standard Web browser techn
Summary of the content on the page No. 10
3. Product Description Please do read the following information to familiarize with NetCam 8001 before you start to install and use it. Front View o Link Indicator o Event Indicator The Network Link LED shows steady, flash or The Event Link LED shows flash green during off during normal operation end depend on detecting moving object or alarm is triggered. setting. Rear Panel o Wireless Antenna Antenna is default to NETCAM 8001W model only. o I/O Terminal Block The I/O
Summary of the content on the page No. 11
Tripod Mounting The NetCam 8001 is supplied with a screw hole for tripod mounting. The screw hole is located on the base of the unit, as shown below. The base plate of the NetCam 8001 is similar, but is supplied with a ceiling or wall mounting plate instead of the tripod screw hole. Wall Mounting the NetCam 8001 Ceiling Mounting the NetCam 8001 The NetCam 8001 is designed exclusively for ceiling/wall mounting and a special mounting plate is supplied for the purpose. Screw th
Summary of the content on the page No. 12
Audio/Video Output Plug the AV converter into the audio/video output. The yellow RCA female plug is for video output. The white RCA female plug is for audio output. Video Audio output output LAN Socket Connect the LAN cable into the LAN socket. LAN socket External alert bus (DI/DO) For more information about DI/DO, refer to Attachment A. Reset to factory settings After turning on the power, insert a slim plastic object into the reset orifice and press for five
Summary of the content on the page No. 13
MIC External alert bus Reset Link LED and Event LED 1. Link LED: The green LED lights up when you transmit images after turning on the camera. 2. Event LED: The green LED flashes when motion or alert detection is implemented after you turn on the camera. Focus knob You can rotate the focus knob clockwise or anticlockwise to acquire the sharpest image. This is not recommend to change unless you can not focus the image. Focus knob ©2007 Asante Networks Inc., All rights rese
Summary of the content on the page No. 14
4. Installing The System Before connecting the hardware 1. Please be aware of that it is required to connect a PC and NetCam 8001 on the same IP network or same Ethernet switch or hub for easier set up. 2. By default, NetCam 8001 is set at 192.168.0.20 private IP address. 3. Or you may use “IPFinder.exe” software come from CDROM alone with document and search available or multiple NetCam 8001 on your network. Wiring the Product Connecting the hardware 1. Connect an Etherne
Summary of the content on the page No. 15
3. External Alarm DI/DO connector – Please refer appendix A. 4. Reset button is to reset the system back to manufacturing default setting. 5. Connect the power cable to the power supply connector and connect it to the main power supply. a. Upon connect the power, Pan/Tilt camera will pan back to start position and Event indicator will show green. 6. If Ethernet has traffic pass through, the Link indicator will be flash. You can now access the NetCam 8001 directly from yo
Summary of the content on the page No. 16
View or set up device via browser System Requirements o Windows 2000 Professional SP4 or XP Home SP2/Profession o 256 MB Memory o Ethernet/WLAN o Internet Explorer 6.x or above o VGA resolution: 800 x 600 or above o CPU ：Pentium 4 2.4 GHz or above (If you would like to monitor multiple IP camera and record, Pentium 4 with 3GHz above or Dual Core Intel process, 1 GB Memory and 32 MB display card are recommended ） Internet Router/Firewall Setting How to access IP Camera f
Summary of the content on the page No. 17
some limitations. Using the Port Forwarding, you can make local computers or servers available to the Internet for different services (for example, FTP or HTTP), to play Internet games (like Quake III), or to use Internet applications (like CUseeMe). Port Forwarding is designed for FTP, Web Server or other server based services like IP Camera web server. Once port forwarding is set up, requests from the Internet will be forwarded to the proper server. For example, the below is an Netg
Summary of the content on the page No. 18
3. Verify Internet browser security. Click menu “tools” and “Internet Options” . Continue click tab on “Security” and press the button on “Default Level”. If your browser is being set into “Medium”, then you may close all pop-up windows meaning you should be able to access video without any blocking. 4. Verify ActiveX Setting : Click IE browser’s “tools” menu, and “internet Options”. Select “Security” and click “Customer Level” then you should see “Security Setting” po
Summary of the content on the page No. 19
5. Verify Window Firewall Setting. Click Control Panel and Window Firewall. If the setting is ON, then the IP video may be blocked but in normal case the Windows may ask if you want to unblock for temporary. It is not recommend to turn off firewall permanently in order to view the video. It is totally user’s decision to change this setting. HTTP is the transport which normally allow in Window Firewall. 6. “tools” and “Internet Options” . Continue click tab on “Security” and
Summary of the content on the page No. 20
Use Internet Explorer (IE) Browser 1. Start a new IE browser 2. Enter NetCam 8001 IP address and enter default username “root” with a default password “root”. 3. You should be able to observe NetCam 8001 control panel and video. If video can not be observed, then you may be blocked by your firewall or router. In case of this, please select HTTP as streaming options which is the most popular available streaming transportation and open ports for most network environment
