Summary of the content on the page No. 1
Summary of the content on the page No. 2
Easy Instr. Manual-E 12/7/02 11:14 am Page 1 Table of Contents Important Information ..........................................................................................2 Precautions ............................................................................................................3 1. Product overview ..................................................................................................4 Important battery information ................................................
Summary of the content on the page No. 3
Easy Instr. Manual-E 12/7/02 11:14 am Page 2 IMPORTANT INFORMATION FCC Statement This device complies with 15 the FCC Rules. Operation is subject to the following two conditions: (i) This device may not cause harmful interference, and (ii) this device must accept any interference received, including interference that may cause undesired operation. CAUTION This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These li
Summary of the content on the page No. 4
Easy Instr. Manual-E 12/7/02 11:14 am Page 3 PRECAUTIONS Test Shots Always take a test photograph to check that the camera is functioning normally. The liability for any incidental losses ( such as the cost of photography or the loss of income from photography ) incurred as a result of fault with this product cannot be accepted. Notes on Copyright Images recorded using your digital camera system cannot be used in ways that infringe copyright laws without the consent of the owner unless inte
Summary of the content on the page No. 5
Easy Instr. Manual-E 12/7/02 11:14 am Page 4 1. Product overview FRONT 1 2 3 1. Shutter button 2. Flash unit 3. Viewfinder 4. Lens 5. USB connector port 5 4 1 2 4 BACK 5 1. Green LED (On/Ready) 2. Red LED (Low light/Busy) 6 3. Status LCD 4. Flash On/Off button 5. Delete button 6. Power/Select button 7. Tripod mount 8. Battery door 3 7 8 4
Summary of the content on the page No. 6
Easy Instr. Manual-E 12/7/02 11:14 am Page 5 Important battery information The Eye-Q Easy camera uses a type of memory that continually draws power to retain the pictures in the camera’s internal memory even if the camera is powered off. If the battery power is depleted and you have not transferred your images to the computer, you will lose them. It is strongly recommended that you transfer your images to the computer promptly and then remove the batteries to extend their life. If you have
Summary of the content on the page No. 7
Easy Instr. Manual-E 12/7/02 11:14 am Page 6 Getting started Congratulations on your purchase of the Concord Eye-Q Easy digital camera. This camera features 8 MB of internal memory allowing you to store still images or short 30 second movie clips in the camera. Please read this manual before operating the camera to become more familiar with the features of this versatile digital camera. Minimum system requirement •Windows 98 Second Edition, 2000 Professional, ME or XP •Pentium 233MHz or high
Summary of the content on the page No. 8
Easy Instr. Manual-E 12/7/02 11:14 am Page 7 Learning the LCD display By default, the 3 digit LCD screen displays the number of images taken. It is also used in conjunction with the Power / Select button and Shutter button to access and display the Eye-Q Easy settings. Normal Video compression Self-timer mode mode mode High No compression compression mode mode Warning Signal Low battery warning When your camera has full power, the Battery indicator on t
Summary of the content on the page No. 9
Easy Instr. Manual-E 12/7/02 11:14 am Page 8 Loading the batteries 2 AA alkaline batteries are included with your camera. 1. Make sure your camera is off. 2. Open the battery door as shown. 3. Insert the batteries with the positive terminal toward the + sign, and the negative terminal toward the - sign. 4. Close the battery door. Important battery information It is strongly recommended that you use fresh batteries to optimize the performance of your camera. You may use alkaline batteries. To
Summary of the content on the page No. 10
Easy Instr. Manual-E 12/7/02 11:14 am Page 9 Turning the camera on/off After inserting the batteries, the camera will automatically power on. The camera is ready for picture taking when the red Busy LED on the back of the camera turns off and the green Ready LED is illuminated. To turn the camera on, press the Power/Select button. The camera will emit two beeps. The camera is ready for picture taking when the red Busy LED on the back of the camera turns off and the green Ready LED is illum
Summary of the content on the page No. 11
Easy Instr. Manual-E 12/7/02 11:14 am Page 10 2. Taking Pictures Photos can be captured in one of three quality modes. These modes differ in photo file size and quality. The compression setting is the default mode for still images. You also have the ability to capture video or take pictures with a self-timer with the Concord Eye-Q Easy digital camera. Mode Resolution Level of compression 640 x 480 Uncompressed 640 x 480 1/4 compression 640 x 480 1/8 compression Movie mode 320 x
Summary of the content on the page No. 12
Easy Instr. Manual-E 12/7/02 11:14 am Page 11 Taking a picture with flash The Concord Eye-Q Easy has two flash modes, Automatic Flash and Flash Off. Flash Off is the default mode. When the red Busy LED on the back of the camera is illuminated there is not sufficient light to yield a good quality image without using the flash. To set the flash, please refer to the Setting the Flash section below. Setting the Flash 1. Turn the camera on by pressing the Power/Select button. 2. Press the Flash
Summary of the content on the page No. 13
Easy Instr. Manual-E 12/7/02 11:14 am Page 12 Taking a movie clip You can record a movie clip in AVI format with your Concord Eye-Q Easy. The resolution of the movie clip is 160 x 120. 1. Turn the camera on by pressing the Power/Select button. 2. Scroll through the menu and select movie mode by pressing the Power/Select button until the movie camera icon appears. 3. Press and hold the shutter button to begin recording. You can record up to 30 seconds of video. However, this duration may var
Summary of the content on the page No. 14
Easy Instr. Manual-E 12/7/02 11:14 am Page 13 Deleting pictures and video You have the option of deleting the last image captured in each quality setting and video mode or you may delete all images and video captured. To delete the last image captured: 1. Scroll through the menu using the Power/Select button. 2. When you find the quality setting from which you’d like to delete, press the Delete Last button. 3. To delete from additional quality settings, continue to scroll through the menu.
Summary of the content on the page No. 15
Easy Instr. Manual-E 12/7/02 11:14 am Page 14 3. Installing the drivers and software Installing the software on a Windows PC 1. Insert the CD-ROM disc into the CD-ROM Drive 2. The CD-ROM disk will autorun and then another window will appear. 3. Select the language and then press “ok” to continue. 4. Press “next” in the welcome page. 5. Press “yes” to agree and continue with the installation or “No” to disagree and quit the installation. 6. Confirm the destination path.
Summary of the content on the page No. 16
Easy Instr. Manual-E 12/7/02 11:14 am Page 15 Uploading your pictures to your PC 1. Make sure that your camera is securely connected to your PC and the USB sign appears on the LCD. 2. Launch the Arcsoft PhotoImpression application. 3. Click on Get Photos and select “Camera/Scanner.” 4. Pull down the “Select Source” manual and a list of devices will be displayed. Select “SE402 Camera” and click on the “Camera/Scanner" button. 5. You can review individual pictures by selecting the camera/sc
Summary of the content on the page No. 17
Easy Instr. Manual-E 12/7/02 11:14 am Page 16 Uploading your video clips to your PC 1. Make sure that your camera is securely connected to your PC and the USB sign appears on the LCD. 2. Launch the Arcsoft PhotoImpression application. 3. Click on Get Photos and select “Camera/Scanner”. 4. Pull down the “Select Source” manual and a list of devices will be displayed. Select “SE402 Camera” and click on the “Camera/Scanner” button. 5. When the Twain driver screen appears, select the movie tab
Summary of the content on the page No. 18
Easy Instr. Manual-E 12/7/02 11:14 am Page 17 Uninstalling the software on a Windows PC You may uninstall the software when the software is no longer required or when the software installation fails. 1. Turn on your PC and start up Windows. 2. Open the “My Computer” windows and double-click on the “Add/Remove Programs” in the Control Panel. 3. Select the application to be uninstalled. The “Add/Remove Programs Properties” windows appears. Select the program to be deleted an
Summary of the content on the page No. 19
Easy Instr. Manual-E 12/7/02 11:14 am Page 18 4. Cleaning and maintenance Be sure to read this information to ensure that you use your camera correctly. Places to Avoid Do not store or use the camera in the following places or locations: •Very humid, dirty or dusty places. •In direct sunlight or in places subject to extreme increases in temperature such as in a closed car during summer. •Extremely cold places. •Places subject to strong vibrations. •Places affected b
Summary of the content on the page No. 20
Easy Instr. Manual-E 12/7/02 11:14 am Page 19 Storing the camera If you do not intend to use the camera for a long period of time, remove the batteries before storing the camera. Cleaning your Camera Use a blower brush to remove dust from the lens and LCD surface and then wipe lightly with a soft, dry cloth. If any soiling remains, apply a small amount of lens cleaning liquid to a piece of lens cleaning paper and wipe gently. Do not scratch hard objects against the lens, LCD screen or view
