Summary of the content on the page No. 1
ENGLISH
OWNER’S MANUAL
MONITOR TV
Please read this manual carefully before operating
your set and retain it for future reference.
MONITOR TV MODELS
M1962DP
M2062DP
M2262DP
M2362DP
M2762DP
www.lg.com
Summary of the content on the page No. 2
CONTENTS CONTENTS MANUAL PROGRAMME TUNING PREPARATION (IN DIGITAL MODE) ...................................47 FRONT PANEL CONTROLS ..............................4 MANUAL PROGRAMME TUNING (IN ANALOGUE MODE) .............................49 BACK PANEL INFORMATION ............................5 PROGRAMME EDIT .........................................51 STAND INSTALLATION ......................................6 IN DTV/RADIO MODE ......................................52 DETACHING STAND ...
Summary of the content on the page No. 3
CONTENTS PRESET SOUND SETTINGS-SOUND MODE ......84 INPUT BLOCK ................................................107 PRESET SOUND SETTINGS-USER MODE ...85 KEY LOCK ......................................................108 Surround X ........................................................85 AUDIO RESET ..................................................86 DIGITAL AUDIO OUT ........................................87 TO USE A USB DEVICE TV SPEAKERS ON / OFF SETUP ...................88 DTV AUDIO SETTI
Summary of the content on the page No. 4
PREPARATION PREPARATION FRONT PANEL CONTROLS ■ This is a simplified representation of the front panel. The image shown may be somewhat different from your set. 1 2 9 3 4 5 6 7 8 Headphone Jack 1 2 IR receiver (Remote controller receiver) INPUT Button 3 MENU Button 4 OK Button 5 6 VOLUME Button 7 PROGRAMME Button 8 Power Button Power Indicator 9 Illuminates blue when the set is switched on. Note: You can adjust Power indicator in the OPTION menu. 4
Summary of the content on the page No. 5
PREPARATION BACK PANEL INFORMATION ■ This is a simplified representation of the front panel. The image shown may be somewhat different from your set. 1 2 3 4 5 6 10 11 7 8 9 PCMCIA (PERSONAL COMPUTER MEMORY CARD Power Cord Socket 1 7 INTERNATIONAL ASSOCIATION) CARD SLOT This set operates on AC power. The voltage is indi- Insert the CI Module to PCMCIA CARD SLOT. cated on the Specifications page. Never attempt to operate the set on DC power. (This feature is not available in all countries.) 8
Summary of the content on the page No. 6
PREPARATION PREPARATION STAND INSTALLATION ■ The image shown may be somewhat different from your set. Carefully place the product screen side down Insert the Stand Base into the product. 1 2 on a cushioned surface that will protect prod- uct and screen from damage. Stand Base Turn the Stand Base Lock through 90° to fix the Stand Base to the Stand Body. 3 4 5 Base Lock 6
Summary of the content on the page No. 7
PREPARATION STAND INSTALLATION ■ The image shown may be somewhat different from your set. Carefully place the product screen side down on a 1 cushioned surface that will protect product and screen from damage. Insert the stand base into the product. 2 Stand Base Use a Coin on the bottom of the stand base 3 and turn the screw clockwise to tighten. Coin 7
Summary of the content on the page No. 8
PREPARATION PREPARATION DETACHING STAND ■ The image shown may be somewhat different from your set. Place the set screen side down on a cushion Detach the monitor to the Stand Base by 1 2 or soft cloth. turning the screw to the left. Turn the Stand Base Lock through 90° to separate the Stand Base from the Stand Body. 3 Pushing Latch inside, Take the stand base from stand body. 4 Latch 8
Summary of the content on the page No. 9
PREPARATION DETACHING STAND ■ The image shown may be somewhat different from your set. Place the set screen side down on a cushion or soft 1 cloth. Detach the monitor to the Stand Base by turning the 2 screw to the left. Turn the screw by using a Coin. Coin Pull the stand base. 3 9
Summary of the content on the page No. 10
PREPARATION PREPARATION DETACHING STAND BODY ■ The image shown may be somewhat different from your set. ■ Remove the Stand Body in the same way as the following when using it as a Wall Hook. 1. Remove the screw 2 point. 2. Pull the stand body. 1. Remove the screw 4 point. 2. Pull the stand body. 10
Summary of the content on the page No. 11
PREPARATION WALL MOUNT : HORIZONTAL INSTALLATION For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed installation instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide. 10 cm 10 cm 10 cm 10 cm 10 cm If you intend to mount the set to a wall, attach Wall mounting interface (optional parts) to the back of the set. When you install the set using the wall mounting interface (optional parts), attach
Summary of the content on the page No. 12
PREPARATION PREPARATION DESKTOP PEDESTAL INSTALLATION ■ The image shown may be somewhat different from your set. For proper ventilation, allow a clearance of 10 cm on each side and from the wall. 10 cm 10 cm 10 cm 10 cm POSITIONING YOUR DISPLAY ■ The image shown may be somewhat different from your set. Adjust the position of the panel in various ways for maximum comfort. * Tilt range -5° 15° 12
Summary of the content on the page No. 13
PREPARATION SWIVEL STAND(Only M2762DP) ■ The image shown may be somewhat different from your set. After installing the set, you can adjust the set manually to the left or right direction by 179 degrees to suit your viewing position. LOCATION Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also, ensure that the set is placed in a position to allow a free flow
Summary of the content on the page No. 14
PREPARATION PREPARATION SECURING THE SET TO THE WALL TO PREVENT FALLING WHEN THE SET IS USED ON A STAND (Only M2762DP) ■ The image shown may be somewhat different from your set. We recommend that you set up the set close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the set be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang
Summary of the content on the page No. 15
PREPARATION ATTACHING THE TV TO A DESK (Only M2762DP) ■ The image shown may be somewhat different from your set. The SET must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only an attached screw. 1-Screw (provided as parts of the product) Stand Desk WARNING ► To prevent SET from falling over the SET should be securely attached to the floor/wall per installation instructions. Tipping,shaking, or rocking the mac
Summary of the content on the page No. 16
PREPARATION PREPARATION KENSINGTON SECURITY SYSTEM - The product is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below. - For detailed installation and use of the Kensington Security System, refer to the user’s guide provided with the Kensington Security System. For further information, contact http://www.kensington.com, the internet homepage of the Kensington company. Kensington sells security systems for expens
Summary of the content on the page No. 17
EXTERNAL EQUIPMENT SETUP EXTERNAL EQUIPMENT SETUP ■ To prevent damage do not connect to the mains outlet until all connections are made between the devices. ANTENNA CONNECTION ■ For optimum picture quality, adjust antenna direction. ■ An antenna cable and converter are not supplied. Multi-family Dwellings / Apartments Wall (Connect to wall antenna socket) Antenna Socket RF Coaxial Wire (75 Ω) Outdoor Antenna Single-family Dwellings / Houses (Connect to wall jack for outdoor antenna) UHF Antenna
Summary of the content on the page No. 18
EXTERNAL EQUIPMENT SETUP EXTERNAL EQUIPMENT SETUP ■ To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment. ■ The image shown may be somewhat different from your set. HD RECEIVER SETUP Connecting with a component cable Connect the video outputs (Y, PB, PR) of the digital 1 set-top box to the COMPONENT IN VIDEO jacks on the SET. Connect the audio output of the digital set-top box 2 to the COMPONENT IN AUDIO jacks on the SET. Turn on the
Summary of the content on the page No. 19
EXTERNAL EQUIPMENT SETUP Connecting a set-top box with a HDMI cable Connect the digital set-top box to HDMI/DVI IN jack 1 on the SET Turn on the digital set-top box. 2 (Refer to the owner’s manual for the digital set-top box.) 1 Select HDMI input source using the INPUT button on 3 the remote control. NOTE ! ► Check that your HDMI cable is High Speed HDMI Cable. If the HDMI cables are not High Speed HDMI Cable, flickering or no screen display can result. Please use the High Speed HDMI Cable.
Summary of the content on the page No. 20
EXTERNAL EQUIPMENT SETUP EXTERNAL EQUIPMENT SETUP Connecting with an HDMI to DVI cable Connect the digital set-top box to HDMI/DVI IN jack on the SET. 1 Connect the audio output of the digital set-top box to the AUDIO IN (RGB/DVI) jack on the SET. 2 Turn on the digital set-top box. 3 (Refer to the owner’s manual for the digital set-top box.) Select HDMI input source using the INPUT button on the remote control. 4 2 1 20
