Master Bilt IM-60 user manual

Summary of the content on the page No. 1

INSTALLATION & OPERATIONS MANUAL

MASTER-BILT Products
908 Highway 15 North
New Albany, MS 38652
Phone: 800-6848988



REV 2-29-12
By: LN

Summary of the content on the page No. 2

TABLE OF CONTENTS I. PACKAGING……………………………………………………………………….………………..3 II. INSTALATION………………………………………………………….…………………………..3 III. OPERATIONS……………………………………………………….…………………….………3-5 1. Electrical………………………………………………………………...………………….…...3 2. Temperature Control…………………………………………..………………………………...4 3. Loading Ice……………………………………………………………….……………….…….5 IV. MAINTENANCE……………………………………………………………………….……………5 1. Refrigeration…………………………………………………………….………………………5 2. Defrosting……………………………………………………………………….………………5 A.

Summary of the content on the page No. 3

Remove plastic overwrap, banding and corrugation packaging. The wooden skid is removed by unscrewing 6-8 hex head screws holding the skid. Glass Door Models: Remove glass door support bracket(s) and protective foam block(s). All merchandisers are tested, inspected and carefully packaged to ensure each unit arrives ready for operation. Please return postage paid warranty card to activate merchandiser warranty. (See back page of manual) Retain for future reference. Note: Merchandi

Summary of the content on the page No. 4

The merchandiser must be plugged into a 115 volt, 60 HZ grounded receptacle electrical outlet with a circuit fuse or breaker. (See figure 1). The condensing unit data plate will indicate the maximum fuse/breaker size. DO NOT use extension cords. Extension cords may decrease the voltage to the unit and ultimately cause the compressor to fail. NOTE: Some outdoor locations require ground fault interrupt (GFI) outlets. These outlets may trip upon condensing unit start. Refrigeration equi

Summary of the content on the page No. 5

3. Loading Ice: After merchandiser is operating at required temperature, load with packaged ice. Stacked packaged ice should not exceed heights that will cause poor refrigeration efficiency. Approximately 6" needs to be clear from top of stacked ice to top of inside interior for effective refrigerated ice storage. Auto- Defrost units require good fan air flow for effective circulation. DO NOT block evaporator assembly fan/grill openings and air channels require unrestricted air flow convect

Summary of the content on the page No. 6

3. Electrical: Inspect each month all power harnesses for any cracks, abrasions or damage to connection plugs. Replace any defective wiring or harnesses. 4. Door(s): Inspect each month for component wear, function and secure attachment. A. Gasket(s) should be examined for tears or any other problems that would cause loss of seal. Replace torn/worn gaskets to maintain correct temperature and refrigeration efficiency. B. Hinges e

Summary of the content on the page No. 7

5. Cleaning: Schedule yearly cleaning of merchandiser interior with solution of 8 tablespoons of baking soda to 1 gallon of warm water. DO NOT use strong detergents, abrasive cleansers, solvents, wax or polish as they are likely to leave objectionable odors which may be absorbed by the ice. Wash the outside surfaces with a mild soap and warm water applied with a soft sponge or cloth. Wax exterior to maintain appearance and extend life of paint.

Summary of the content on the page No. 8

8

Summary of the content on the page No. 9

9

Summary of the content on the page No. 10

10

Summary of the content on the page No. 11

11

Summary of the content on the page No. 12

ITEM DESCRIPTION PART # ITEM DESCRIPTION PART # 1. Condensing Unit: Provide 14. Door, Stucco Stainless Steel 5590025 condensing unit model number 27" x 27" with gasket 15. Door Gasket for 1030016 2. Drier 1323002 27" x 27" solid door Timer 1328023 Thermostat 1328046 1911019 16. Door Hinge with cover for 27" x 27" Power Harness (AD & CW) 1270047 solid door Coldwall

Summary of the content on the page No. 13

13

Summary of the content on the page No. 14