Summary of the content on the page No. 1
TRUE FOOD SERVICE EQUIPMENT, INC.
2001 East Terra Lane � P.O. Box 970 � O’Fallon, Missouri 63366
(636)-240-2400 � FAX (636)272-2408 � INT’L FAX (636)272-7546 � (800)325-6152
Parts Department (800)424-TRUE � Parts Department FAX# (636)272-9471
INSTALLATION MANUAL FOR
TCGDZ DISPLAY CASES (DUAL ZONE) MODELS
TABLE OF CONTENTS
Safety Information
Safety Precautions ––––––––––––––––––––––– 1
Proper Disposal –––––––––––––––––––––––––– 2
Connecting Electricity ––––––––––––––––––––– 3
Adapter Plugs
Summary of the content on the page No. 2
NOTICE TO CUSTOMER: Loss Or Spoilage Of Products In Your Refrigerator/Freezer Is NOT Covered By Warranty. In Addition To Following Recommended Installation Procedures You Must Run The Refrigerator/Freezer 24 Hours Prior To Usage. True Manufacturing Company, Inc.
Summary of the content on the page No. 3
True Food Service Equipment, Inc. SAFETY INFORMATION How to Maintain Your Unit to Receive the Most Efficient and Successful Operation You have selected one of the finest display cases made. It is manufactured under strict quality controls with only the best quality materials available. Your TRUE cooler, when properly maintained, will give you many years of trouble-free service. WARNING! Use this appliance for its intended purpose as described in this Owner Manual. SAFETY PRECA
Summary of the content on the page No. 4
True Food Service Equipment, Inc. SAFETY INFORMATION DANGER! RISK OF CHILD ENTRAPMENT PROPER DISPOSAL OF THE DISPLAY CASE Child entrapment and suffocation are not problems Refrigerant Disposal of the past. Junked or abandoned display cases Your old refrigerator may have a cooling system are still dangerous… even if they will sit for “just a that uses “Ozone Depleting ” chemicals. If you are few days.” If you are getting rid of your old display throwing away your old refrigerator, make sure
Summary of the content on the page No. 5
True Food Service Equipment, Inc. SAFETY INFORMATION WARNING! HOW TO CONNECT ELECTRICITY Hard wiring is required on specific Display Cases. Models standard with power cords: Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded. Before your new display case is connected to a If the outlet is a standard 2-prong outlet, it is your power supply, check the incoming voltage with a personal respon
Summary of the content on the page No. 6
True Food Service Equipment, Inc. INSTALLATION / OPERATION INSTRUCTIONS INSTALLATION / OPERATION INSTRUCTIONS OWNERSHIP To insure that your unit works properly from the Before you start to install your True unit, carefully first day, it must be installed properly. We highly inspect it for freight damage. If damage is discov- recommend a trained mechanic and electrician ered, immediately file a claim with the delivery install your True equipment. The cost of a profes- freight carrier. sio
Summary of the content on the page No. 7
True Food Service Equipment, Inc. INSTALLATION / OPERATION INSTRUCTIONS LOCATING Warning and tape. Remove fiberglass tape securing glass. For proper performance of refrigerated cabinet an Remove components: (shelves, brackets, etc.) ambient temperature no greater than 75°F (24°C) from inside cabinet. with a relative humidity of 55% is required. TOOLS REQUIRED: � Phillips screw driver 3 3 � /8” (9.5 mm) socket or /8” (9.5 mm) wrench Step 2 A. Use a Phillips screw diver and remove four 1
Summary of the content on the page No. 8
True Food Service Equipment, Inc. INSTALLATION / OPERATION INSTRUCTIONS ELECTRICAL INSTRUCTIONS Step 4 Warning For proper performance of refrigerated cabinet an A. Before your new unit is connected to a power ambient temperature no greater than 75°F (24°C) with supply, check the incoming voltage with a volt- a relative humidity of 55% is required. meter. If anything less than 100% of the rated voltage for operation is noted, correct immedi- WARNING ately. Compressor warranties are void i
Summary of the content on the page No. 9
True Food Service Equipment, Inc. INSTALLATION / OPERATION INSTRUCTIONS CONDUCTORS AND CIRCUITS Wire Gauge for 2% Voltage Drop in Supply Circuits. 115 Volt Distance In Feet To Center of Load Amps 20 30 40 50 60 70 80 90 100 120 140 160 2 14 14 14 14 14 14 14 14 14 14 14 14 3 14 14 14 14 14 14 14 14 14 14 14 12 4 14 14 14 14 14 14 14 14 14 12 12 12 5 14 14 14 14 14 14 14 12 12 12 10 10 6 14 14 14 14 14 14 12 12 12 10 10 10 7 14 14 14 14 14 12 12 12 10 10 10 8 8 14 14 14 14 12 12 12 1
Summary of the content on the page No. 10
True Food Service Equipment, Inc. INSTALLATION / OPERATION INSTRUCTIONS STARTUP Step 5 REPLACEMENT PARTS TRUE maintains a record of the cabinet serial number A. The compressor is ready to operate. Plug in the for your unit. If at any time during the life of your dis- display case. play case, a part is needed, you may obtain this part B. Check the temperature control setting in the by furnishing the model number and serial number lower right of the cabinet backside. The set- to the compa
Summary of the content on the page No. 11
➟ True Food Service Equipment, Inc. INSTALLATION / OPERATION INSTRUCTIONS SHELVING INSTALLATION (REFRIGERATED BAKERY) SHELF INSTALLATION: A. Lift each door up and out of track (do not dis- connect elastic tubing). Stretch elastic surgical tubing and set doors on each side of unit. B. Locate brackets, lights, shelves, etc. from cabinet interior. 1 C. Locate shelf supports wrapped in micro foam and install teeth end into stainless pilasters Install shelf supports. located on interior walls
Summary of the content on the page No. 12
True Food Service Equipment, Inc. INSTALLATION / OPERATION INSTRUCTIONS OPTIONAL (INSTALLING OPTIONAL CASTORS) CASTOR INSTALLATION: TOOLS REQUIRED: � Castor wrench (if not included contact True) � Adjustable wrench NOTE Castors not available for hard wired or remote models. WARNING 1 Make sure unit is empty of all its contents (shelv- ing, shelving lighting). Make sure power supply has been disconnected. A. Curved glass can be damaged if you lay unit Back out leg levelers by hand, or with
Summary of the content on the page No. 13
True Food Service Equipment, Inc. INSTALLATION / OPERATION INSTRUCTIONS OPTIONAL (INSTALLING OPTIONAL FORMICA KIT) FORMICA KIT INSTALLATION: NOTE After installing the bottom end pieces the top end FORMICA KIT COMPONENTS: panel will stay in place. 3 (2) Formica Top End Panels 10 /4"w x 33"h (27.3 cm x 83.8 cm). C. Install the bottom end Formica panels (one on (2) Bottom End Panels each side. (1) left side, (1) right side (Formica glued to (Formica is pre-glued to black plastic panel).
Summary of the content on the page No. 14
True Food Service Equipment, Inc. MAINTENANCE, CARE & CLEANING OPTIONAL (SEALING CABINET TO FLOOR) It may be necessary to seal the bakery case to the floor C. When applying a mastic, thoroughly clean both for local sanitary codes or if the customer so desires. the cabinet and floor of dirt and grease. Draw TRUE recommends either of the following methods. an outline of the cabinet on the floor. Raise and block the front side of the cabinet. Apply a bead A. Using a vinyl cove base trim a
Summary of the content on the page No. 15
➟ ➟ True Food Service Equipment, Inc. MAINTENANCE, CARE & CLEANING LIGHT BULB REPLACEMENT SHELF MOUNTED BULB REPLACEMENT: WARNING When replacing a light bulb make sure power to the unit is either turned off or unplugged. A. Unplug the light assembly from the receptacle on the interior side wall. Remove shelf and light assembly from cabinet. B. Remove the lampshield by gently squeezing the sides together and rotating out (image 1). 1 C. Remove bulb from the corded end of assembly 2 by holdi
Summary of the content on the page No. 16
True Food Service Equipment, Inc. MAINTENANCE, CARE & CLEANING TEMPERATURE CONTROL ADJUSTMENT FOR HIGH ALTITUDE ONLY! TERMS: NOTE Mechanical temperature controllers are affected � Cut-out - Temperature sensed by the controller that shuts the compressor off. when functioning at high altitude. The Cut-in and cut-out temperatures will be colder than when the � Cut-in - Temperature sensed by the controller controller functions closer to sea level. that turns the compressor on. D. For high e
Summary of the content on the page No. 17
True Food Service Equipment, Inc. MAINTENANCE, CARE & CLEANING CLEANING THE CONDENSER COIL When using electrical appliances, basic safety precautions should be followed, including the following CONDENSER CLEANING: TOOLS REQUIRED: � Phillips screwdriver � Stiff bristle brush � Adjustable wrench � Vacuum A. Disconnect power to unit. B. Take off rear lower grill assembly by removing two (2) bottom screws. If necessary, loosen screws holding the top pivot pins. Swing grill up and remove frame
Summary of the content on the page No. 18
Condensing Unit Air Air Airflow flow flow True Food Service Equipment, Inc. MAINTENANCE, CARE & CLEANING IMPORTANT WARRANTY INFORMATION Condensers accumulate dirt and require cleaning every 30 days. Dirty condensers result in compressor failure, product loss, and lost sales... which are not covered by warranty. If you keep the Condenser clean you will minimize your service expense and lower your electrical costs. The Condenser requires scheduled cleaning every thirty days or as needed. Air i
Summary of the content on the page No. 19
True Food Service Equipment, Inc. MAINTENANCE, CARE & CLEANING STAINLESS STEEL EQUIPMENT CARE AND CLEANING CAUTION: Do not use any steel wool, abrasive or chlorine based products to clean stainless steel surfaces. � Stainless Steel Opponents There are three basic things which can break down your stainless steel’s passivity layer and allow corrosion to rear its ugly head. 1) Scratches from wire brushes, scrapers, and steel pads are just a few examples of items that can be abrasive to
Summary of the content on the page No. 20
True Food Service Equipment, Inc. MAINTENANCE, CARE & CLEANING STAINLESS STEEL EQUIPMENT CARE AND CLEANING Recommended cleaners for certain situations / environments of stainless steel A) Soap, ammonia and detergent medallion applied with a cloth or sponge can be used for routine cleaning. B) Arcal 20, Lac-O-Nu Ecoshine applied provides barrier film for fingerprints and smears. C) Cameo, Talc, Zud First Impression is applied by rubbing in the direction of the polished lines for
