Instrukcja obsługi Harbor Freight Tools Haul Master 2000 LB. CAPACITY A-FRAME TRAILER JACK 92626

Streszczenie treści zawartej na stronie nr. 1

2000 LB. CAPACITY
A-FRAME TRAILER JACK
92626
SET UP AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
© ®
Copyright 2010 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this ma

Streszczenie treści zawartej na stronie nr. 2

NOTICE is used to SAVE THIS MANUAL address practices Keep this manual for the safety not related to personal injury. warnings and precautions, assembly, CAUTION, without operating, inspection, maintenance and the safety alert cleaning procedures. Write the product’s symbol, is used to address serial number in the back of the manual practices not related to near the assembly diagram (or month personal injury. and year of purchase if product has no number). Keep this manual and the

Streszczenie treści zawartej na stronie nr. 3

This enables better control of the will ensure that the safety of the tool tool in unexpected situations. is maintained. d. Dress properly. Do not wear Specific Safety Warnings loose clothing or jewelry. Keep your hair, clothing and gloves 1. Do not exceed 2000 Lb. capacity. away from moving parts. Loose clothes, jewelry or long hair can be 2. Use on flat, level, hard surface caught in moving parts. capable of supporting load. 3. Tool use and care 3. Wear ANSI-approved safety goggles

Streszczenie treści zawartej na stronie nr. 4

14. The warnings, precautions, Specifications SPECIFICATIONS and instructions discussed in this instruction manual cannot Weight Capacity 2000 lb. cover all possible conditions and Jack Lift 15” situations that may occur. It must Installation Bolt on or Weld on Mounting be understood by the operator that Handle Rotates 360 degrees common sense and caution are factors which cannot be built into this Height 24-1/4” product, but must be supplied by the operator. UNPACKING SAVE THESE

Streszczenie treści zawartej na stronie nr. 5

not specifically designed for it. An Assembly example of an A-frame hitch is shown 1. Raise the Trailer Jack to its in Figure 1. uppermost position. Insert the Foot Plate (11) over the bottom of the Figure 1 Inner Tube (2). Example of hitch (not included) 2. Insert the Locking Pin (12) to secure the Foot Plate in place. See Figure 3 below and the assembly diagram on page 9. Figure 3 Locking Pin (12) 4. Insert the top of the Trailer Jack up through the

Streszczenie treści zawartej na stronie nr. 6

7. Now that the Trailer Jack is fully 7. Carefully back your vehicle into place assembled, test it by raising the within a foot or two of the trailer hitch enough to remove the supports tongue. inserted in Step 2 on page 4. 8. Raise the Trailer Jack until the hitch is in a position to clear or fit over the Operation OPERATING INSTRUCTIONS hitch ball. Read the ENTIRE IMPORTANT 9. With assistance, roll the Trailer or the SAFETY INFORMATION vehicle into position so that the trailer secti

Streszczenie treści zawartej na stronie nr. 7

SERVICING User Maintenance Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning and Maintenance 1. BEFORE EACH USE, inspect the general condition of the Trailer Jack. Check for loose hardware, misalignment or binding of moving parts, cracked or broken parts, an

Streszczenie treści zawartej na stronie nr. 8

PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEM

Streszczenie treści zawartej na stronie nr. 9

ASSEMBLY DIAGRAM Assembly Diagram SKU 92626 For technical questions, please call 1-800-444-3353. Page 9

Streszczenie treści zawartej na stronie nr. 10

LIMITED 90 DAY WARRANTY Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activ