Instrukcja obsługi Nissan 4073

Streszczenie treści zawartej na stronie nr. 1

WARNING
This body lift kit should only be installed on vehicles that are in
good working condition. Before the installation begins, the
vehicle should be thoroughly inspected for evidence of corrosion
or deformation of the sheet metal around the factory body
mounts. This body lift kit should not be installed on any vehicle
that is suspected to have been in a collision, or misused. Off
road use of you vehicle with this body lift installed may increase
the stress applied to the factory

Streszczenie treści zawartej na stronie nr. 2

up and out of the bottom mount. Remove the radiator from the WARNING vehicle. The Supplemental Restraint System (SRS, air bag) must be deactivated during installation of the lift kit to avoid accidental 7. Loosen the two hose clamps that mount both heater hoses to deployment of the air bag while working near SRS sensors and the heater core at the firewall (passenger side). wiring. Do not allow anyone near the air bag during installation of the lift kit. Accidental deployment can

Streszczenie treści zawartej na stronie nr. 3

bushing, the frame perch, the stock top bushing, the block, and WARNING threading into the nut that is captured inside the body. Reinstall Use extreme caution when working near fuel lines and fuel tank. the two bolts that mount the outside support bracket to the Clean up spilled fuel immediately. Any spark could cause an bottom of the frame perch. Do not tighten any of the bolts at this explosion or fire resulting in serious personal and property time. damage. 22. Repeat step #21

Streszczenie treści zawartej na stronie nr. 4

We recommend the use of loctite or a similar adhesive on all enough slack in the line to remount it to the core support. If there steering hardware. is not enough slack, carefully bend the line to gain more slack. Be sure that there is ample slack in the line. Install the bolt that 26. Using the new lower radiator support as a template, Mark the mounts the a/c line to the core support. Tighten securely. lower core support for alignment of the new support. Align the holes in the new brack

Streszczenie treści zawartej na stronie nr. 5

tank. Using a #6 hose clamp, attach the small hose to the fuel WARNING tank. Reconnect the remaining small hose to the filler neck. Raising the rear bumper is intended to enhance the appearance of Tighten all hose clamps securely. Install the screws that mount the vehicle only. The rear bumper will no longer be rated for the filler neck to the body. Tighten securely. Replace the fuel towing of any kind. Attempting to tow with the rear bumper cap. after it has been raised can result in

Streszczenie treści zawartej na stronie nr. 6

thoroughly. Test-drive the vehicle in all gears and 4 wheel drive CAUTION ranges. Pay very close attention to all vehicle systems. Check all All fasteners should be retorqued after 500 miles and after off hardware again in 500 miles and as part of your regular road use. All body lift components should be visually inspected maintenance schedule. and fasteners retorqued during routine vehicle servicing. CAUTION 47. Double-check the vehicle. Check all mounting hardware to Performanc

Streszczenie treści zawartej na stronie nr. 7

PARTS LIST 4 #6 hose clamps Kit 2 #10 hose clamps 1 Transmission shifter extension bracket 2 #28 hose clamps 2 Front bumper brackets 2 3/8" x 3" scd. 40 cab safety strap 1 Lower radiator support bracket 1 3/8" x 4" scd. 40 heater hose extension 1 Parking brake cable relocation bracket 1 7/16" x 3" .049" vacuum hose extension 2 Outside cab support brackets 2 1/8" x 3/4" roll pins 1 1 3/4" x 3" fuel-filler extension