Instrukcja obsługi Chief Manufacturing Security SLM Series Mount RPMA1

Streszczenie treści zawartej na stronie nr. 1

INSTALLATION INSTRUCTIONS
Security SLM Series Mount
RPMA1, -B1, -C1

Streszczenie treści zawartej na stronie nr. 2

RPMA1, -B1, -C1 Installation Instructions DISCLAIMER WARNING: Failure to read, thoroughly understand, and CSAV, Inc., and its affiliated corporations and subsidiaries follow all instructions can result in serious personal injury, (collectively, "CSAV"), intend to make this manual accurate and damage to equipment, or voiding of factory warranty! It is the complete. However, CSAV makes no claim that the information installer’s responsibility to make sure all components are contained herein covers

Streszczenie treści zawartej na stronie nr. 3

Installation Instructions RPMA1, -B1, -C1 LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging lo

Streszczenie treści zawartej na stronie nr. 4

RPMA1, -B1, -C1 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 5/32" (Provided) PARTS Q (1) S (1) 5/32" T (8) U (4) V (4) R (4) A (4) 10-24 x 1/4" D (4) G (4) K (4) M (4) (NOT USED) M5 x 12mm M2.5 x 10mm M5 x 12mm M4 B (4) H (4) E (4) L (4) N (4) M3 x 10mm M6 x 12mm M3 x 10mm M6 x 12mm M6 C (4) F (4) J (4) P (4) M4 x 10mm 1/4-20 x 1/2" M4 x 10mm O (1) 3/32" 4

Streszczenie treści zawartej na stronie nr. 5

Installation Instructions RPMA1, -B1, -C1 6. Pull RPMA1 bottom away from RPMA1 top. ASSEMBLY AND INSTALLATION Attaching Projector Security Legs Installing Ceiling Plate and Disassembling RPMA1 1. Attach the projector security legs (R) to the projector, using the correct size screws and washers for your specific projector. (See Figure 3) WARNING: IMPROPER INSTALLATION CAN RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO x 4 EQUIPMENT! Structural members MUST be capable of supporting five times the

Streszczenie treści zawartej na stronie nr. 6

RPMA1, -B1, -C1 Installation Instructions 2. Remove the paper backing from the adhesive washers (V) and attach projector to RPMA1 bottom using adhesive washers (V) and thumbnuts (P) over the security legs (R). (See Figure 5) (P) x 4 (V) x 4 4 RPMA1 Bottom Security Legs (R) 5 Projector Figure 7 Attachment areas if using an 4. Move locking lever to "Locked" position. (See Figure 7) optional SLB bracket. 5. Insert key into lock and turn to secure projector to mount. Figure 5 (See Figure 7) Attachin

Streszczenie treści zawartej na stronie nr. 7

Installation Instructions RPMA1, -B1, -C1 3. Tighten YAW adjustment locking screw using a #2 Phillips Rough Alignment of RPMA1 screwdriver. 1. Turn RPMA1 clockwise or counterclockwise until the front of the RPMA1 and projector is facing target. (See Figure 9) PITCH Adjustment 1. Loosen PITCH adjustment locking screw using a #2 Phillips screwdriver. (See Figure 11) 1 2. Turn PITCH micro-adjustment screw right or left using a #2 Phillips screwdriver until image is properly aligned on target. 3. Ti

Streszczenie treści zawartej na stronie nr. 8

RPMA1, -B1, -C1 Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Asia Pacific A Room 30I, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112 8802-000254 2007 Chief Manufacturing www.chiefmfg.com P +86-755-8996 9226 ; 8996 9236 ; 8996 9220 04/07 F +86-75