Instrukcja obsługi Kenmore 564.8815022

Streszczenie treści zawartej na stronie nr. 1

' I_ARS
BEER DISPENSER
OWNER'S INSTRUCTIONS
Kenmore
MODEL 564.8815022
THIS BOOK:
r_... t_, _n. how to operate and care for your beer dispenser. It also offers tips on how to get the
best, as well as lowest cost, performance.
...... _^-;'", ,,_l=r_.rn_.rlt oarts use For parts or service information, call
VVlI_:;': ,J,,,,,,_ .... ._ -_
the part number. Do not use the illustra- your nearest Sears store or Service
tion number.
Center, give the complete model num-
ber listed above.
ice provided belo

Streszczenie treści zawartej na stronie nr. 2

Read and understand these instructions thoroughly before installing b. Push wingnut and beer tube of draft arm assembly beer dispenser. through hole in top of cabinetuntil draft arm is resting on cabinettop. c. Alignholesin draftarm base withholes ingasket and pilot ASSEMBLY holes in cabinet top, then secure draft arm to cabinet top 1. Carton Inventory withfour hex head screws (5mm dia x 15mm). Unpack and inspect the parts. Make sure all items are present 4. Install Guard Rail (See Fig. 1). and

Streszczenie treści zawartej na stronie nr. 3

a. Your CO2 cylinder is shipped empty to avoid any possible accident during transportation. When you purchase the Pressure Vessel first keg of beer, get CO_ cylinder filled by your beer • Donotremove valve from CO2 cylinder. distributor. • CO2 cylinder should be handled only by trained, experi- b. Follow the procedure on the inside front cover page of enced personneland in accordance withthe safe handl- "Draught Beer Facts" book for installation of CO2 regulator ing practicesrecommended by the c

Streszczenie treści zawartej na stronie nr. 4

REPLACING EMPTY KEG Close shutoff valve on CO2 regulator then remove keg tappel from empty keg. To tap a new keg, follow the procedures C, D and E of "Installing Keg Tapper and Beer Keg." Keg j. Support Cabinet Bottom (1) Lift to upright i / / I / (2) Slide into cabinet. Fig. 3 OPERATION Place drip tray under beer faucet. To dispense beer, open beer faucet quickly all the way. If you have any trouble with beer, refer to "Draught Beer Facts" book. The recommended pressure for the CO2 system is 8-

Streszczenie treści zawartej na stronie nr. 5

PARTS LIST MODEL 564.8815022 CAUTION: Use Kenmore part number on all orders, not the illustration number. Illus. Part Illus. Part No. No. Description No. No. Description 1. 300746 Door Liner 46. 300773 Evaporator Assembly 2. 300747 Door Gasket 47. 300480 Machine Screw 3. 300748 Door 48. 300494 Tapping Screw 4. 300308 Tapping Screw 49. 300475 Insulation,Tube 5. 300749 Hinge, Upper 50. 301957 Retainer, Relay Cover 6. 300459 Bolt 51. 301956 Relay Cover 7. 300750 BeerTube Insulation 52. 300736 PTC T

Streszczenie treści zawartej na stronie nr. 6

34 1 33 2 4 29 26 23 22 18 12 13 14

Streszczenie treści zawartej na stronie nr. 7

55 53 56 52 49 48 7 41 i 46 45

Streszczenie treści zawartej na stronie nr. 8

"TR" DRAUGHT ARM PARTS _ 4301 -- 4302 -- 4306 D-19-60AC _) -- 4308 _--4311 \ ,_ 4312 \ -- 4313 O I0 _,_ 4318 4322 4324 4328 D9R • r , I ( D-8 759 I D7P D-6 D-5N D-2 Part No. Description D-19-60AC Beer Tube Assembly 759 Washer D-2 Coupling Nut D-5N Shank DI2-2P D12-1 D-6 Outside Flange D7P Inside Flange _'_ 0-15-2P D-8 Lock Nut D9R Gland © D14-9 D-10 Inverted Flare Nut 4301 Black Knob 4302 Knob Lever Collar 4306 Knob Lever Bonnet 4308 FrictionWasher 4311 Ball Washer 4312 Brass Lever 4313 Stainles