Instrukcja obsługi Harbor Freight Tools 47996

Streszczenie treści zawartej na stronie nr. 1

WELDING HELMET WELDING HELMET
WELDING HELMET WELDING HELMET WELDING HELMET
AUTO-DARKENING AUTO-DARKENING
AUTO-DARKENING AUTO-DARKENING AUTO-DARKENING
47996
ASSEMBLY AND OPERATING INSTRUCTIONS
Important: Read and understand the entire manual before using the
welding helmet.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2002 by Harbor Freight Tools . All rights reserved. No portion of this manual or
any artwork contained herein may b

Streszczenie treści zawartej na stronie nr. 2

Specifications ITEM DESCRIPTION For MIG / MAG, Flux Cored, TIG, Plasma / For MIC / MAG, Flux Cored, TIC, Plasma / Welding Protection Types Microplasma Arc Microplasma Arc Not Protected From Laser welding and oxyhydrogen welding Filter Standard ANSI Z87.1 -- 1989 (R1998) Standard Switch On / Off to use power from internal batteries; auto-off High impact resistant plastic polyamide nylon; Construction Full Face; Retainer and ratchet headband Shade Control: Clear state # 3; Dark: DIN 4, 9 ~ 13 Dark

Streszczenie treści zawartej na stronie nr. 3

designed. Do not modify this tool and do not use this tool for a purpose for which it was not intended. 7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically non-conductive clothes and non-skid footwear are recommended when working. Wear restrictive hair covering to contain long hair. 8. Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear a full face shield if you are producing metal filings or w

Streszczenie treści zawartej na stronie nr. 4

Repair or replace damaged components immediately. Replace the two AAA backup batteries often. 5. Be sure the welding filter shade setting is correct for your application. 6. Test the helmet auto-darkening filter lens before welding. While wearing the helmet, briefly strike an arc, keeping your face and eyes turned slightly away from the arc, and to one side. The lens should darken even when not directly facing the arc. If it does not darken after repeated tests, replace the lens filter. 7. Impac

Streszczenie treści zawartej na stronie nr. 5

WARNING: This Helmet does not provide protection for LASER AND OXYHYDROGEN welding. 1. Verify that the batteries are good. 2. Turn the helmet over and adjust the Shade Knob to the desired shade (9 ~ 13). 3. Push the Switch Button to turn the lens on and open the window. 4. Adjust the helmet Side Knobs for a proper fit. Tighten the Lens Clamp Screws. 5. Put on a pair of safety glasses first, then the helmet. 6. While looking to one side, strike an arc briefly (see # 6 above). Check to see if the

Streszczenie treści zawartej na stronie nr. 6

Replacing the Lens Cover Lift the Lens Cover and remove the clear plastic. Replace it when it becomes scratched, cracked, or pitted, and cannot be cleaned. Removing the Lens 1. Turn the Helmet over to view the Lens from the inside. 2. Unscrew the two Lens Unit Screw Clamps (10). Pull it out from the inside. Troubleshooting The following lists possible causes for non operation: 1. Batteries are not inserted correctly. 2. Battery Cover not completely secure. 3. Batteries are dead. 4. On / Off Butt

Streszczenie treści zawartej na stronie nr. 7

Assembly Drawing (3) (2) (10) (4) (1) (7) (9) (5) (6) (9) (5) (7) (8) (9) (9) (8) (7) (7) (5) (5) (6) SKU 47996 Page 7