Instrukcja obsługi Transition Networks TN-GLC-LH-SM

Streszczenie treści zawartej na stronie nr. 1

User’s Guide
TN-GLC-xx-xx and TN-CWDM-SFP-1xx0 Cisco
CompatibleSmall Form Factor Pluggable (SFP)
Transceiver Modules**
TN-GLC-T
The Transition Networks TN-GLC-xx-xx and TN-CWDM-
SFP-1xx0 series small form factor pluggable (SFP) transceiver
modules are designed to install in any SFP port, allowing for1000Base-T, 1000Base-SX
or 1000Base-LX interfaces to the network through the SFP connector. The TN-GLC-xxx
and TN-CWDM-SFP-1xx0 transceivers are designed for bi-directional serial-optical data
commun

Streszczenie treści zawartej na stronie nr. 2

TN-GLC-xx-xx SFPs ***Provide 100Base-FX interface when plugged into a gigabit SFP slot on Cisco Part Number Port Description catalyst 3750, 3560, and 2970 series switches. TN-GLC-BX-U 1000Base-BX, Simplex LC 1310 nm Tx/1490 nm Rx, Note: Install simplex or single fiber SFP models in pairs in the same network where single mode, single fiber 10 km (6.2 miles)* one is the local SFP and the other is the remote SFP. TN-GLC-BX-D 1000Base-BX, Simplex LC 1490 nm Tx/1310 nm Rx, single mode, single fibe

Streszczenie treści zawartej na stronie nr. 3

TN-GLC-xx-xx SFPs Installing the fiber cables Cable Specification 1. Locate or build 1000Base-SX-compliant or 1000Base-LX-compliant fiber Copper cable (Category 5 -- minimum requirement) cable with male TX to RX connectors installed at both ends. • Gauge = 24 to 22 AWG; Attenuation = 22.0 dB /100m @ 100 MHz 2. Install the fiber cable as shown below. • Straight-through OR crossover cable may be used. • Shielded twisted-pair (STP) OR unshielded twisted-pair (UTP) may be used • All pin pairs (1&2,

Streszczenie treści zawartej na stronie nr. 4

TN-GLC-xx-xx SFPs Fiber cable -- continued Fiber cable TN-GLC-FE-100FX 1300 nm multimode The physical characteristics must meet or exceed IEEE 802.3z™ specifications. TN-GLC-GE-100FX 1300 nm multimode Singlemode fiber (recommended): 9 µm Fiber Optic Transmitter Power: min: -23.5 dBm max: -14.0 dBm Multimode fiber (recommended): 62.5/125 µm Fiber Optic Receiver Sensitivity: min: -32.0 dBm max: -8.0 dBm Multimode fiber (optional): 100/140, 85/140, 50/125 µm Link Budget: 8.5 dB TN-GLC-SX-MM

Streszczenie treści zawartej na stronie nr. 5

TN-GLC-xx-xx SFPs Technical Specification Contact Us For use with Transition Networks Model TN-GLC-xxx or equivalent. Technical support Technical support is available 24 hours a day. Standard: IEEE 802.3 2003; ANSI X3.297-1997 U.S.A. and Canada: 1-800-260-1312 TN-GLC-FE-xxx and TN-GLC-GE-xxx: Compiant with International: 00-1-952-941-7600 IEEE 802.3 100Base-Fx; IEEE802.3ah 100Base-Bx; Intermediate - Reach Sonet OC-3/SDH STM-1 (s-1-1) Transition now TN-GLC-xx-xx and TN-CWDM-SFP-1xx0 modules: Ch

Streszczenie treści zawartej na stronie nr. 6

TN-GLC-xx-xx SFPs Compliance Information Declaration of Conformity CE Mark: IEC-60825; FDA 21; CFR 1040.10 and 1040.11 Name of Mfg: Transition Networks 10900 Red Circle Drive, Minnetonka MN 55343 U.S.A. FCC regulations Model: TN-GLC-xx-xx Series Transceiver Modules This equipment has been tested and found to comply with the limits for a Class A digital device, Part Number(s): TN-GLC-T, TN-GLC-SX-MM, N-GLC-SX-MM-2k, pursuant to part 15 of the FCC rules. These limits are designed to provide r

Streszczenie treści zawartej na stronie nr. 7

TN-GLC-xx-xx SFPs Trademark notice All trademarks and registered trademarks are the property of their respective owners. Copyright restrictions © 2004 Transition Networks. All rights reserved. No part of this work may be reproduced or used in any form or means (graphic, electronic, mechanical) without written permission from Transition Networks. Printed in the U.S.A. 33389.D 12