Instrukcja obsługi Perle Systems S-4GPT-DSFP

Streszczenie treści zawartej na stronie nr. 1

Perle
Protocol Transparent
Standalone
Media Converters


Installation Guide
S-4GPT-DSFP
S-4GPT-DSFP-XT










Part # 5500334-10

Streszczenie treści zawartej na stronie nr. 2

Overview This document contains instructions necessary for the installation and operation of the Perle Protocol Transparent Standalone Media Converters. These Media Converters allow connection and cross- connection of fiber networks of different types to each other. They are protocol independent using standard SFP* modules with speeds up to 4.25 Gbps. *(purchased separately) Supported modes of operation o Multimode to multimode o Multimode to single mode o Single mode to single

Streszczenie treści zawartej na stronie nr. 3

Installation The default switch settings (all switches in the UP position) will work for most installations. See the Operation section of this guide for more details. The converter comes equipped with a bank of DIP switches and set of jumpers for setting configuration. The following steps are used to configure the Media Converter. 1. Set the DIP switch settings (optional). 2. Insert the SFP modules (purchased separately) into the transceiver ports. 3. Connect the power cord strain re

Streszczenie treści zawartej na stronie nr. 4

and reflects this on the TX port of the other SFP by turning off the transmitter. When the signal (Link) gets restored and Signal Detector becomes active the affected transmitter gets re-enabled. Standard Mode: In Standard Mode the media converter will monitor the fiber link in the same manner. If Signal Detect goes down the media converter will output a 25MHz signal on the TX port of the other SFP. Fiber Fault Alert (Switch 2) Switch Position Mode Up (default) Enabled Down Disabled

Streszczenie treści zawartej na stronie nr. 5

Attaching the Power Cord Strain Relief Clip For extra power cable strain relief, attach the strain clip to the side of the unit, then thread the power cable through the clip in either one or two loops. 5

Streszczenie treści zawartej na stronie nr. 6

Operation Powering up the Perle Media Converter 1. Connect the Perle supplied power adapter to the media converter. 2. Turn on the power at the source. 3. Check that the PWR LED light is lit. Terminal Block Connector 1. Ensure the Power Source is off prior to connection. 2. Strip insulator sheathing from both wires 5mm (3/16th inch) to expose the copper conductor wire. 3. Loosen the terminal block screws and connect Positive (+) wire to the left terminal. Connect the Negative (-) wir

Streszczenie treści zawartej na stronie nr. 7

Technical Specifications Extended Max Power Input Commercial Temperature Consumption 6-30 VDC 0.625A 325mA at 12VDC 325mA at 12VDC Max Operating 0°C - 50°C -40°C - 75°C Temperature (32°F - 122°F) (-40°F - 167°F) -25°C - 70°C -40°C - 85°C Storage Temperature (-13°F - 158°F) (-40°F - 158°F) Operating Humidity 5% to 90% non-condensing Storage Humidity 5% to 95% non-condensing Operating Altitude Up to 3,048 m (10,000 ft) Note: Please refer the product page on the Perle websi

Streszczenie treści zawartej na stronie nr. 8

Compliance Information EMI/EMC EN 55022/CISPR22 EN 55022/CISPR22 FCC This product has been found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions in this Guid