Streszczenie treści zawartej na stronie nr. 1
TDM
A U D I O
24CX-2
24CX-3
24CX-4
ELECTRONIC CROSSOVER
OWNER’S MANUAL
TDM AUDIO INC.
7270 BELLAIRE AVE.
NORTH HOLLYWOOD, CA 91605
(818) 765-6200
TDMAUDIO.COM
Streszczenie treści zawartej na stronie nr. 2
IMPORTANT! *** Read Before Using *** CAUTION: The following must be observed to prevent malfunctioning and/or possible equipment damage. • Before plugging the unit into the main AC line, make sure that all of the equipment following the crossover output lines is turned off or all of the inputs are turned down. • Never change the frequency range switch from the x10 to x1 position (or vice versa) with the crossover output levels passing signal. Transients can result and speaker damage
Streszczenie treści zawartej na stronie nr. 3
Table of Contents INTRODUCTION .......................................................................................................................................................4 CROSSOVER FUNDAMENTALS.....................................................................................................................................4 CROSSOVER TERMINOLOGY ......................................................................................................................................
Streszczenie treści zawartej na stronie nr. 4
Introduction hank you for purchasing the TDM 24CX series electronic crossover. These units are made Tfrom the finest components and engineered to exacting standards. Precision components are used in all critical circuitry for the finest sonic quality and performance. To get the most out of your new crossover, please take a few minutes to review this manual and familiarize yourself with the proper operation of the unit. The remainder of this section provides background information about th
Streszczenie treści zawartej na stronie nr. 5
Signal Source Power Amplifier Passive Crossover Low Transducer Mid Transducer High Transducer Figure 1 - Typical Passive Crossover Configuration This kind of crossover is called a passive crossover because it does not use any power other than the power contained in the signal to accomplish its task. Passive crossovers have certain limitations that make them inappropriate for large systems, or systems requiring high fidelity at high sound pressure levels. Some of these limitations are…
Streszczenie treści zawartej na stronie nr. 6
• External Power: Passive crossovers are simply inserted between the amp and the speaker components. Active crossovers must be plugged into an electrical outlet in order to work. • Higher Typical Rolloff Rates: Passive crossovers typically roll off at rates from 6 to 12 dB per octave. Most modern active crossovers have rates of at least 24 dB per octave (more about rolloff rates later). • More Power Amplifiers: Active crossovers break the signal into many different bands before the power
Streszczenie treści zawartej na stronie nr. 7
result in a greater overall efficiency of the system by making sure a band of frequencies is always reproduced by the speaker components that are most efficient at reproducing it. How Crossovers Work To divide a range of frequencies into two or more smaller ranges, a crossover uses filter circuits. A filter is simply a circuit that lowers the levels of unwanted frequencies in a signal. There are two different kinds of filters used in crossovers: • High Pass Filters: These reduce the levels
Streszczenie treści zawartej na stronie nr. 8
5 0 -5 -10 -15 -20 -25 -30 -35 -40 -45 Frequency (Hz) Figure 4 - 24 dB per Octave Filter Curve To make a 2-way crossover, we feed the same signal into a high-pass filter and a low-pass filter with the same cutoff frequency. This is called the crossover frequency. The output of the high- pass filter is the high output of the crossover. The output of the low-pass filter is the low output of the crossover. The crossover frequency knob simultaneously adjusts the cutoff frequencies of both filt
Streszczenie treści zawartej na stronie nr. 9
The crossover frequency of 1000 Hz is where the two lines on this graph cross over each other. In crossovers with three or more output bands, there are two filters for each of the middle bands. A low-pass filter rolls off frequencies above a certain cutoff point. A high-pass filter rolls off frequencies below a certain cutoff point. This leaves a band of frequencies in the middle. These middle bands have two different cutoff points. Figure 6 shows the responses of the three bands of a thre
Streszczenie treści zawartej na stronie nr. 10
Mounting the Unit in a Rack DM 24CX series crossovers can be mounted in any standard 19” rack. Each TDM 24CX series crossover takes up one rack space. To make mounting easier, lay the rack on its back T with the equipment front panels facing up. Remove any rack screws from the part of the rack where you are planning to mount the crossover. Position the TDM 24CX series crossover in the rack as desired. Make sure the mounting holes in the crossover line up with the screw holes in the rack ra
Streszczenie treści zawartej na stronie nr. 11
Hooking Up the Crossover nce your TDM crossover is installed in the rack, you are ready to hook it up to your Oequipment. Of course, the method used to hook up any crossover depends on how it will be used. We will try to give you the basics in this manual, but you may need to tailor the methods described here to your particular application. What You’ll Need To connect your 24CX series crossover to your equipment, you will need the following. • Power: A power outlet should be located close
Streszczenie treści zawartej na stronie nr. 12
It is very important that both pins 1 and 3 are wired to the sleeve. Some adapters leave pin 3 floating, and with TDM crossover units this will cause problems. If you have a TDM 24CX series crossover with ¼” connectors, you may connect directly to other equipment using ¼” connectors whether the other equipment is balanced or not. If you wish to connect a TDM 24CX series crossover with ¼” connectors to another piece of equipment that has XLR connectors, and you are making the adapters yourse
Streszczenie treści zawartej na stronie nr. 13
channels to link them together and form one three-way channel. This switch may be found on the rear of the unit between the channels. It is recessed into the chassis through a small, square hole, and you might need to use a small screwdriver to press it. When it is in the in position, the channels are linked. When it is in the out position, the channels are not linked. Connect the output of your signal source to the input of channel one (or channel three if your are using channels three and
Streszczenie treści zawartej na stronie nr. 14
Operating the Crossover nce you have mounted your TDM 24CX series crossover in a rack and connected all of the Ocables, the unit is ready for operation. At this time, make sure the input levels on the front of the crossover and the input levels of the amplifiers are all the way down. Next, turn all equipment on. It is always best to turn the equipment on in the order of the signal path from input to output and to turn it off in exactly the reverse order. For example, in a live sound reinfo
Streszczenie treści zawartej na stronie nr. 15
Channel One (or Three) Input Level Input Level Channel One (or Three) Crossover Frequency High-To-Mid Crossover Frequency Channel One (or Three) Range Switch High-To-Mid Range Channel One (or Three) High Output Level High Output Level Channel One (or Three) Low Output Level Not Used Channel Two (or Four) Input Level Not Used Channel Two (or Four) Crossover Frequency Mid-To-Low Crossover Frequency Channel Two (or Four) Range Switch Mid-To-Low Range Channel Two (or Four) High Output Level
Streszczenie treści zawartej na stronie nr. 16
Checking the Hookup It is critical that the crossover is connected and adjusted correctly before use. To avoid speaker damage, we recommend checking your hookup and settings using the following method. 1. Make sure the input level and all output levels on the crossover are down. Adjust the crossover frequencies according the recommendations of your speaker manufacturer. 2. Turn on the amplifiers and raise their gains about halfway up (leaving the levels on the crossover all the way down).
Streszczenie treści zawartej na stronie nr. 17
Adjusting the Output Levels Start with the input levels at 0 dB (unity gain). After the rest of the system has been dialed in (amplifier gains and output levels), the input levels can be fine tuned. Feed a lower-than-normal level signal from your signal source into the system. You want to make sure that you set it up so you have room to spare. If you can get enough volume out of the system when your input signal is at -10 dBm then you probably have enough gain, so use some program material
Streszczenie treści zawartej na stronie nr. 18
TDM Option Cards he TDM 24CX series crossovers have internal connectors for option cards. A variety of different option cards is available from TDM. Plugging a card into the connector inserts the T circuitry on the card between a crossover section output and the output of the unit. The most common card to use for this application is the high-pass filter card. This card is used on the low- frequency section of the crossover to remove subsonic frequencies from the output. This helps remove st
Streszczenie treści zawartej na stronie nr. 19
Optional Output Limiters he TDM 24CX series crossovers can be ordered with output limiters. These let you set the maximum level for each crossover output. Limiters are used to help protect speaker T components and ears from damage by excessive levels. Levels above the preset threshold are reduced automatically by the limiter circuit. If your TDM 24CX series crossover has limiters installed, you will find a set of small, yellow, “trimmer” knobs recessed into the bottom of the unit—one near
Streszczenie treści zawartej na stronie nr. 20
Troubleshooting and Support his section details various problems that you might encounter when using your crossover, and the possible causes and solutions. It also tells how to contact TDM when you need T service or support for your 24CX series crossover. No Signal Output If you are getting a signal from some of the frequency bands, but one or more of them is not working, check the cables and hookups for the band(s) in question. Make sure the cable between the crossover output and the amp
