Streszczenie treści zawartej na stronie nr. 1
Streszczenie treści zawartej na stronie nr. 2
CONTENTS Step 1. Unpacking ............................................. 3 Step 2. Understanding Your Printer ................... 5 Step 3. Installing the Transfer Belt and Toner Cartridges 7 Step 4. Loading Paper ..................................... 14 Step 5. Connecting a Printer Cable .................. 17 For Local Printing ......................................17 For Network Printing ..................................18 Step 6. Turning the Printer On ........................ 19 Step 7. Pr
Streszczenie treści zawartej na stronie nr. 3
English Step 1. Unpacking 1 Remove the printer and all of the accessories from the packing carton. Make sure that the printer has been packed with the following items: Toner Cartridges Power Cord Quick Install Guide CD-ROM Optimum Setup Guide SyncThru CD-ROM SyncThru Quick Guide (CLP-510N only) (CLP-510N only) NOTES: • If any items are missing or damaged, notify your dealer immediately. • Components may differ from one country to another. • The CD-ROM contains the printer driver, the User’s
Streszczenie treści zawartej na stronie nr. 4
2 Carefully remove all of the packing tape from the printer. 3 Pull the paper tray out of the printer and remove the packing tape from the tray. 4 Select a location for the printer: •Leave enough room to open the printer trays, covers, and to allow for proper ventilation. •Provide the proper environment: – A firm, level surface – Away from direct airflow of air conditioners, heaters, or ventilators – Free of temperature, sunlight, and humidity extremes or fluctuations – Clean, dry, and
Streszczenie treści zawartej na stronie nr. 5
English Step 2. Understanding Your Printer These are the main components of your printer: Top Cover Paper Output Tray (Open to install the transfer belt.) Output Support Control Panel (Refer to Chapter 2 in the User’s Guide on the CD-ROM.) Top Cover Release Button Front Cover (Open to replace the waste toner container.) Handle (Use it to lift the printer. Lifting handles are located at the lower edge of both sides of the printer.) Tray 1 (250-sheet paper feeder) Left Cover (Open fully to i
Streszczenie treści zawartej na stronie nr. 6
Right Cover (Open to remove paper jams.) Muti-purpose Tray (Open to load special print materials.) Handle Optional Tray 2 Jam Cover (Use it to lift the printer.) (Open to remove jams from the optional tray 2.) Wireless Network Antenna* Network Port** Control Board Cover USB Port (Open to install optional accessories.) Power Switch Power Receptacle * A wireless network card is not supplied with the printer. It is an option that must be purchased and installed separately. ** The network port is f
Streszczenie treści zawartej na stronie nr. 7
English Step 3. Installing the Transfer Belt and Toner Cartridges 1 Using the handle, completely open the left cover until it is at right angles to the main frame. CAUTION: If the left cover is not completely open, the top cover release button will remain locked. 2 Press the top cover release button to unlatch the top cover and open it all the way. Remove the label on the transfer belt. Top cover release button SETUP GUIDE 7
Streszczenie treści zawartej na stronie nr. 8
3 Take the transfer belt out of the printer. NOTE: The image unit is already installed in your printer. 4 Remove the protective devices on both side of the transfer belt. 8 SETUP GUIDE
Streszczenie treści zawartej na stronie nr. 9
English 5 Locate the transfer belt slots inside the printer, one on each side. CAUTION: To prevent damage, do not expose the imaging unit to light for more than a few minutes. Close the top and left covers should the insallation need to be halted for any reason. 6 Holding the handle on the transfer belt, align it with the slots on either side of the inside of your printer. NOTE: Keep the transfer belt level. Do not turn the transfer belt over, or loose toner may be spilled. SETUP GUIDE 9
Streszczenie treści zawartej na stronie nr. 10
7 Slide the transfer belt down into the printer and press it firmly into place. 8 Firmly push the lock levers on each side toward the top cover, as shown below, to lock the transfer belt into place. CAUTION: If you leave the left cover open for more than a few minutes, the imaging unit can be exposed to light. This causes damage to the imaging unit. Close the left cover should the installation need to be halted for any reason. 10 SETUP GUIDE
Streszczenie treści zawartej na stronie nr. 11
English 9 After making sure that the left cover is open, close the top cover. Make sure that it is securely latched. CAUTION: Do not try to close the left cover with the top cover open. This may cause damage to the printer. 10Take the toner cartridges out of their packages. CAUTION: Do not use sharp objects, such as a knife or scissors, to open the toner cartridges packages. You could damage the surface of the toner cartridges. SETUP GUIDE 11
Streszczenie treści zawartej na stronie nr. 12
11Holding both sides of each of the toner cartridges, gently roll them from side to side to evenly distribute the toner. 12Place the toner cartridges on a flat surface, as shown, and remove the paper covering the toner cartridge by removing the tape. NOTE: If toner gets on your clothing, wipe it off with a dry cloth and wash it in cold water. Hot water sets toner into fabric. 13On the right hand side of the toner cartridge slot is a label that identifies which color cartridge goes into each
Streszczenie treści zawartej na stronie nr. 13
English K Y C M 14Holding each toner cartridge with both hands, insert them into their corresponding positions in the following order: Cyan, Magenta, Yellow, and then Black. Then use the handle to fully slide the cartridge in. Grip here. When the toner cartridges are correctly installed, the yellow and black cartridges will not be fully inserted. These will automatically move into place when you close the left cover. 15Close the left cover. Make sure that it is securely latched. If you have
Streszczenie treści zawartej na stronie nr. 14
Step 4. Loading Paper The tray (Tray 1) can hold a maximum of 250 sheets of plain paper. You can use A4 and letter-sized paper. To load paper: 1 Pull the tray out of the printer. 2 Push down on the metal plate until it locks into position. 3 Flex the paper sheets back and forth to separate the pages and then fan them while holding one edge. Tap the edges of the stack on a flat surface to even it up. 14 SETUP GUIDE
Streszczenie treści zawartej na stronie nr. 15
English 4 Load paper with the print side facing up. Make sure that all four corners are flat in the tray and under the corner brackets, as shown below. 5 Do not exceed the maximum stack height. Overfilling the tray may cause a paper jam. SETUP GUIDE 15
Streszczenie treści zawartej na stronie nr. 16
6 Squeeze the paper guide, as shown, and side it to the stack of paper until it lightly touches the side of the stack. Do not press the guide too tightly against the edge of the paper as it will cause the paper to bend. NOTE: If you want to change the size of the paper in the tray, refer to your printer’s User’s Guide on the CD-ROM. 7 Slide the tray back into the printer. NOTES: • Do not push the width guide far enough to cause the material to warp. • If you do not correctly adjust the w
Streszczenie treści zawartej na stronie nr. 17
English Step 5. Connecting a Printer Cable For Local Printing To print from your computer in a local environment, you need to connect your printer to the computer with a Universal Serial Bus (USB) cable. NOTE: Connecting the printer to the USB port of the computer requires a certified USB cable. You will need to buy a USB 2.0 compliant cable that is 3m or less in length. 1 Make sure that both the printer and the computer are turned off. 2 Plug the USB printer cable into the connector on t
Streszczenie treści zawartej na stronie nr. 18
For Network Printing You can attach your CLP-510 or CLP-510N printer to a network using an Ethernet cable (UTP cable with RJ.45 connector). The CLP-510N has a built-in network interface card. If you are a CLP-510 user, you need to install an optional network interface card. If you want to use the printer in both wired and wireless network environments, you need to install an optional wired/wireless network interface card. For details about installing the card, see your printer’s User’s G
Streszczenie treści zawartej na stronie nr. 19
English Using a network antenna If you install a wired/wireless network card, you can use your printer in a wireless environment. For details about installing a wired/wireless network card, see your printer’s User’s Guide on the CD-ROM. NOTE: After connecting the printer, you need to configure the network parameters on the control panel. See your printer’s User’s Guide. You can use the software supplied with the card. Refer to the software User’s Guide. Step 6. Turning the Printer On 1 Plu
Streszczenie treści zawartej na stronie nr. 20
Step 7. Printing a Demo Page Print a demo page to make sure that the printer is operating correctly. To print a demo page: In ready mode, press and hold the Upper Level button ( ) on the control panel for 2 seconds to print a demo page. A demo page showing the printer’s features and capabilities is printed. Step 8. Changing the Display Language To change the language that is displayed on the control panel, take the following steps: 1 In ready mode, press the Menu button ( ) on the control p
