Streszczenie treści zawartej na stronie nr. 1
INSTRUCTION MANUAL
12" Dual-Bevel Compound
Miter Saw
(Model 36-412)
PART NO. A05726 - 10-21-04
Copyright © 2004 Delta Machinery
To learn more about DELTA MACHINERY
ESPAÑOL: PÁGINA 23
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call 1-800-223-7278 (In Canada call 1-800-463-3582).
Streszczenie treści zawartej na stronie nr. 2
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ADDITIONAL S
Streszczenie treści zawartej na stronie nr. 3
SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situ
Streszczenie treści zawartej na stronie nr. 4
GENERAL SAFETY RULES FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY. 1. FOR YOUR OWN SAFETY, READ THE INSTRUC- 13. USE RECOMMENDED ACCESSORIES. The use TION MANUAL BEFORE OPERATING THE of accessories and attachments not recommend- MACHINE. Learning the machine’s application, ed by Delta may cause damage to the machine or limitations, and specific hazards will greatly mini- injury to the user. mize the possibility of accidents and injury. 14. USE THE PROPER EXTENSION CORD. Make 2. USE
Streszczenie treści zawartej na stronie nr. 5
ADDITIONAL SAFETY RULES FOR MITER SAWS FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY. 18. ALLOW THE MOTOR TO COME TO FULL SPEED prior 1. DO NOT OPERATE THIS MACHINE until it is completely to starting cut. Starting the cut too soon can cause assembled and installed according to the instructions. A damage to the machine or blade and/or serious injury. machine incorrectly assembled can cause serious injury. 19. NEVER REACH AROUND or behind the saw blade. A 2. OBTAIN ADVICE from your su
Streszczenie treści zawartej na stronie nr. 6
POWER CONNECTIONS A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3- prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of the same ch
Streszczenie treści zawartej na stronie nr. 7
EXTENSION CORDS MINIMUM GAUGE EXTENSION CORD RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES Use proper extension cords. Make sure Ampere Total Length Gauge of Rating Volts of Cord in Feet Extension Cord your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type 0-6 120 up to 25 18 AWG plug and matching receptacle which will accept the 0-6 120 25-50 16 AWG 0-6 120 50-100 16 AWG machine’s plug. When using an extension cord, be sure 0-6 1
Streszczenie treści zawartej na stronie nr. 8
DO NOT OPERATE THIS MACHINE UNTIL YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. 1. Carefully remove the machine from the carton. Retain all packing materials until you have inspected and satisfactorily operated the machine. 2. Place the machine on a firm, level surface with proper support of the workpiece. 3. The 36-412 is shipped with the cuttinghead beveled right to 45° and locked in the down position, and the table rotated 45° left. To release the head and move it to the operating po
Streszczenie treści zawartej na stronie nr. 9
A B C E E D Fig. 5 Fig.6 MOVING TABLE TO THE 0° CUT-OFF POSITION 1. Rotate the locking knob (A) Fig. 5 counter-clockwise as far as it will go. Depress the lever (B) and rotate the table (C) to the 0° straight cut-off position, release the lever (B), and tighten the locking knob (A). NOTE: This saw incorporates a new slotted plate design feature (D) Fig. 6 with location adjustment screws (E) for fine-adjusting the cutting angle. 2. For proper operation and adjustment of the table, refer to sectio
Streszczenie treści zawartej na stronie nr. 10
FASTENING MACHINE TO SUPPORTING A A SURFACE Before operating your compound miter saw, firmly mount it to a workbench or other supporting surface. Four holes (A) Fig. 9 are provided for fastening the saw to a supporting surface. When frequently moving the saw from place to place, mount the saw to a 3/4” piece of plywood. The saw can then be easily moved from place to place and the plywood can be clamped to the supporting surface using “C” clamps. Fig. 9 OPERATIONS OPERATIONAL CONTROLS AND ADJUSTM
Streszczenie treści zawartej na stronie nr. 11
ROTATING TABLE FOR MITER CUTTING C A B D E B F F G Fig. 13 Fig. 14 1. The compound miter saw will cut any angle from a straight 0° cut to 48° right and left. Turn the locking knob (A) Fig. 13 counterclockwise, depress the lock lever (B), and rotate the table to the desired position. 2. This machine is equipped with positive stops at the 0° cut-off position and at the 15°, 22.5°, 31.6°, and 45° left and right positions. 3. The center line (C) Fig. 14 on the cursor indicates the actual angle of cu
Streszczenie treści zawartej na stronie nr. 12
4. Adjust the miter curser (F) Fig. 17 so that the pointer is aligned with the 0° mark on the scale by loosening the screw (G), adjusting the cursor (F), and tightening the screw (G). 5. Place one end of a framing square (A) Fig. 18 against the front of the right fence base (B) and the other end against the left fence base (C). Using the supplied wrench (D) Fig. 18, loosen the left fence base mounting screws and adjust the left fence base parallel to the right fence base. A D F B G C Fig. 17 Fig
Streszczenie treści zawartej na stronie nr. 13
SELECTING 0°, 33.9°AND 45° BEVEL POSITIVE STOPS C The bevel setting feature utilizes a sliding plate (A) Fig. 24, pin (B), and bushing (C) design that is used to select the bevel angle. The position of the pin (B) and the sliding plate (A) determine the bevel angle. B DISCONNECT THE MACHINE FROM THE A POWER SOURCE. 1. Position the bevel detent plate so that the desired angle (A) Fig. 23 is exposed immediately to the left or right of the housing (H) Fig. 23. 2. Lift the front handle (A) Fig. 22
Streszczenie treści zawartej na stronie nr. 14
C D D B C A A Fig. 29 Fig. 30 NOTE: Shown from the rear, Fig. 30 illustrates the sliding plate position and bushing (C) adjustment for 45° left and Fig. 31 illustrates the sliding plate position and bushing (C) C adjustment for 45° right. MAKE SURE THAT THE FENCES ARE CLEAR OF THE GUARD AND BLADE BEFORE OPERATING THE SAW. Fig. 31 ADJUSTING THE BEVEL LOCK The bevel-locking force has been set at the factory. After a period of time, you may need to adjust the locking mechanism. To adjust, place the
Streszczenie treści zawartej na stronie nr. 15
C B C A D B D Fig. 35 Fig. 36 ADJUSTING LOWER BLADE GUARD The 36-412 incorporates an moveable lower blade guard (C) Fig. 36, and it also has a secondary blade guard (B) to cover the rear section of the blade. After an extended period of use, the moveable lower blade guard (C) Fig. 36 may not operate smoothly when the cuttinghead is lowered. This can be corrected by adjusting nut (D) until the lower blade guard (C) moves freely. OVERTIGHTENING THE NUT COULD IMPAIR GUARD MOVEMENT. NOTE: This unit
Streszczenie treści zawartej na stronie nr. 16
AUXILIARY FENCE SPACER This machine is supplied with new design features that increase cutting capacity. The unit can (1) crosscut 4" x 6" dimensional lumber at 0° miter and 0° bevel, (2) miter left and right 45° 4" x 4" dimensional lumber, and (3) bevel right 45° 2" x 8" dimensional lumber with a user provided spacer (A) Fig. 38. NOTE: The spacer can be made from a 2" x 4" or any other 2" material as shown in Fig. 38. INCORRECT CORRECT FENCE FENCE BLADE BLADE Fig. 39 Fig. 40 CUTTING ALUMINUM T
Streszczenie treści zawartej na stronie nr. 17
CUTTING CROWN MOULDING (USING BUILT-IN STOPS) Crown moulding stops have been built in to the base to aid in holding the workpiece in position while cutting. This new design feature allows cutting crown moulding in either the flat or nested position and utilizes a stop and screw feature that can be quickly adjusted to accommodate several widths of crown moulding. The position of the stops can be adjusted by two methods. To adjust, turn knob (A) Fig. 43 until stop (B) is in the proper position to
Streszczenie treści zawartej na stronie nr. 18
A NEW FEATURE FOR THIS TOOL IS CROWN MOULDING STOPS BUILT INTO THE BASE. DELTA DOES NOT CONSIDER THE CROWN MOULDING STOPS TO BE WORK CLAMPS AND THEY ARE NOT TO BE USED IN THIS MANNER. MAKE SURE THAT THE FENCES ARE CLEAR OF THE GUARD AND BLADE BEFORE OPERATING THE SAW. WHEN CUTTING CROWN MOULDING USING THE CROWN MOULDING STOPS, DO NOT BEVEL THE CUT. THE CROWN MOULDING STOP FEATURE IS DESIGNED TO MAKE THE CUT WITH THE CUTTINGHEAD AT 90° AND WITH THE TABLE ROTATED 45°. B A D C Fig. 46A Fig. 46B A
Streszczenie treści zawartej na stronie nr. 19
5. Place the crown moulding on the table with the WALL 1 EDGE of the crown moulding against the fence and 2 make the cut. Again, the piece of crown moulding used for the outside corner will always be on the right side of the blade, as shown at (C) Fig. 48. The piece of crown moulding used for the inside corner will CA always be on the left side of the blade, as shown at (D) Fig. 48. 6. Fig. 49 illustrates the two outside corner pieces; (1) being the piece cut at (A) Fig. 47 and (2) being the Fi
Streszczenie treści zawartej na stronie nr. 20
CHANGING THE BLADE The 36-412 incorporates a moveable lower blade guard, and it also has a secondary blade guard to cover the rear section of the blade. Make sure there is minimal gap between the two guards when the cuttinghead is in its uppermost position. MAKE SURE THAT THE FENCES ARE CLEAR OF THE GUARD AND BLADE BEFORE USING SAW. OVER-TIGHTENING THE NUT COULD IMPAIR GUARD MOVEMENT. DO NOT REMOVE ANY OF THE BLADE GUARDS. MAKE SURE THAT ALL GUARDS ARE IN PLACE AND FUNCTIONING PROPERLY BEFORE O
