Instrukcja obsługi DeWalt DW 718

Streszczenie treści zawartej na stronie nr. 1

• TURN THE MACHINE “OFF”, AND DISCONNECT THE MACHINE FROM THE POWER
SOURCE before installing or removing accessories, before adjusting or changing set-ups,
when making repairs or changing locations. An accidental start-up can cause injury. Do not
touch the plug’s metal prongs when unplugging or plugging in the cord.
• REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure that the switch is in the
“OFF” position before plugging in the power cord.
• USE PROPER EXTENSION CORD. Make sure you

Streszczenie treści zawartej na stronie nr. 2

WARNING: Do not connect unit to electrical power source until complete instructions are FIG. 1 read and understood. WARNING: Always wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss. DW7080 WARNING: NEVER MAKE ANY CUT UNLESS THE MATERIAL IS SECURED ON THE TABLE AND AGAINST THE FENCE. WARNING: Some dust created by power sanding, sawing, grinding, drilling, an

Streszczenie treści zawartej na stronie nr. 3

45º bevel - Left FIG. 4 Max. Height 2.4" (61 mm) Result Width 12.9" (328 mm) RAIL LOCK Max. Width 13.6" (345 mm) Result Height 1.9" (48 mm) KNOB LIFTING MOTOR 45º bevel - Right HANDLE HOUSING RAIL SET Max. Height 1.7' (43 mm) Result Width 12.9" (328 mm) SCREW Max. Width 13.6" (345 mm) Result Height 1.1" (28 mm) ADJUSTMENT Your saw is capable of cutting baseboard moldings 0.8" (20 mm) thick by 6.5" (165 mm) tall MOTOR on a 45º right or left miter. ENDCAP NOTE: Your saw is capable of

Streszczenie treści zawartej na stronie nr. 4

FIG. 10 FIG. 9 Tighten the center nut. The 45º bevel stops require adjustment after the bevel square to table FENCE KNOB adjustment is complete. (ONE EACH SIDE) BEVEL POINTER (FIG. 8) If the bevel pointers do not indicate zero, loosen each screw that holds each bevel pointer in place and move them as necessary. BEVEL STOP 45º RIGHT AND LEFT ADJUSTMENT (FIG. 8) Your saw has two 45º bevel adjustments, one for the right, and one for the left. The procedure is the same for each. To align the 45º

Streszczenie treści zawartej na stronie nr. 5

FIG. 23 FIG. 24 WARNING: Always use eye protection. All users and bystanders must wear eye protection that conforms to ANSI Z87.1 (CAN/CSA Z94.3). Plug the saw into any household 60 Hz power source. Refer to the nameplate for voltage. Be sure the cord will not interfere with your work. SWITCH To turn the saw on, depress the trigger switch. To turn the tool off, release the switch. Allow the blade to spin up to full operating rpm before making the cut. Release the trigger switch SCREWS and al

Streszczenie treści zawartej na stronie nr. 6

WARNING: Ensure the saw is mounted firmly to a stable flat surface. Failure to do so could BEVEL SETTING TYPE OF CUT cause the saw to be unstable and fall causing personal injury. RIGHT SIDE, INSIDE CORNER: 4. Place the workpiece to be cut on top of the platform mounted to the table. Ensure the 1. Top of molding against fence. 33.85° Right workpiece is firmly against the backfence (Fig. 25). 2. Miter table set at left 31.62° 5. Secure the material before cutting. Cut slowly through the m

Streszczenie treści zawartej na stronie nr. 7

SQUARE BOX 6-SIDED BOX 8-SIDED BOX TABLE 1: COMPOUND MITER CUT (POSITION WOOD WITH BROAD FLAT SIDE ON THE TABLE AND THE NARROW EDGE AGAINST THE FENCE) 10 20 30 40 50 10 20 60 30 40 10 20 50 30 70 40 60 50 60 70 80 70 80 80 SET THIS BEVEL ANGLE ON SAW SET THIS MITER ANGLE ON SAW ANGLE OF SIDE OF BOX (ANGLE A)