Streszczenie treści zawartej na stronie nr. 1
Vacuum Cleaner
MODEL 406
(Dry type)
INSTRUCTION MANUAL
DOUBLE
INS U L AT I 0 N
Net
Dimensions
Peak air flow Sealed sunction Recoverable capacity (L x W x H)
weight
478 mm x 422 mm x 699 mm 10.3 kg
3.0 m3”in.
2,100mm (83”) 32 P(8.3 gal.) (,8-,/8r, 16.5,8rr 27.112aa) (22.7 1bs)
(106 cu.ft./min.) of water
Manufacturer reserves the right to change specifications without notice.
Note: Specifications may differ from country to country.
WARNING: For your personal safety, READ and UNDERS
Streszczenie treści zawartej na stronie nr. 2
I M PO RTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE WARNING -TO reduce the risk of fire, electric shock, or injury: 1. Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. 2. Do not use on wet surfaces. Do not expose rain. Store indoors. 3. Do not allow to be used as a toy. Close attention is necessary when
Streszczenie treści zawartej na stronie nr. 3
16. AVOID UNINTENTIONAL STARTING. Be sure switch is OFF when plugging in. 17. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 18. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces. For example; pipes, radiators, ranges, refrigerator enclosures. 19. This appliance is provided with double insulation. Use only identical replace- ment parts. See instructions for Servicing of Double-Insulated App
Streszczenie treści zawartej na stronie nr. 4
ADDITIONAL SAFETY RULES 1. This is a dry type cleaner. Do not attempt to pick up liquids, sharp materials such as razors, needles, broken glass or the like. 2. Do not use close to heat sources (stoves, etc.). 3. Do not fold, tug nor step on the hose. 4. Clean and service the cleaner immediately after each use to keep it in tiptop operating condition. 5. Be kind to your cleaner. Rough handling can cause breakage of even the most sturdily built cleaner. 6. Do not attempt to clean the exte
Streszczenie treści zawartej na stronie nr. 5
Installing hose Insert the hose into the hose inlet and turn Hose inlet clockwise until fully secured. I Installing cloth filter Install the cloth filter on the tank. Always be sure that there is no gap between the gasket on the cloth filter and the tank after installing FT Cloth filter Tank -/ Switch action To start the cleaner, press the "ON" side of Switch the switch. To stop, press the "OFF" side of the switch. CAUTION: .Do not operate the cleaner for a long time with intak
Streszczenie treści zawartej na stronie nr. 6
Storage of accessories A wand holder (pipe holder) is equipped on of the cleaner to keep the the side straight/bent wand (pipe) out of the way during vacuuming breaks. Both the straight wand (straight pipe) and bent wand (bent pipe) can be stored after use just by inserting them in the holes in the cleaner base. 6
Streszczenie treści zawartej na stronie nr. 7
MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Cleaning Clogged filters cause poor suction performance. Clean out the filters from time to time. To remove dust or particles adhering to the cloth filter, shake the frame bottom quickly several times. Moreover, occasionally wash the cloth filter in soapy water, rinse and dry thoroughly in the shade before use. Never wash filters in a washing machine
Streszczenie treści zawartej na stronie nr. 8
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. *Nozzle assembly *Bending pipe Part No. 12251 24 Part No. 192562-3 *Hose *Straight pipe Inner dia. 19 mm (3/4") Part No. 192563-1 Part No. 192108-5 (2.5 m: 8 ft.) Inner dia. 28 mm (1-1/8"
Streszczenie treści zawartej na stronie nr. 9
The following joints are available for use with some type Makita planers, belt sanders, miter routers, etc. saws, Joint name & configuration Applicable model Concrete Planer PC1100 Belt Sanders 9401, 9402 Elbow joint 32 Ass'y Part No. JPA 122273 Miter Saws 24008, LS 1400 m Joint 40 Ass'y Part No. JPA 122274 Planers 19008. N 19008. 1901 Nozzle 51 - 1 + Joint 55 Ass'y Part No. 191569-6 Part No. JPA 122275 Nozzle + Joint 55 Ass'y Part No. JPA 122275 Part No. JPA 122276 18058 No
Streszczenie treści zawartej na stronie nr. 10
Aug.--23--'96 US VACUUM CLEANER Model 406 Note: The switch, noise suppressor and other part configurations may differ from country to country. 10
Streszczenie treści zawartej na stronie nr. 11
MODEL 406 Aug.-23-'96 US 'LiM $fb DESCRIPTION ';"OM $fD DESCRIPTION MACHINE MACHINE ~ ~ 11 Name Plate 34 1 Return Base 21 35 1 Fan 125 Cowling 31 Block Filter 36 1 Flat Washer 10 41 1 Hex Nut M8 s e p a r a t 0 r 37 61 Switch Base 38 1 Fan Cover 71 Switch 39 1 Support Ring 40 1 Guard 81 0"St cover cap 41 1 Float 91 Dust Cover 10 1 Strain Relief 42 3 Tapping Screw 4x18 2 43 1 Float Cage 11 Tapping Screw 4x18 12 1 Cord 44 1 Frame 13 1 Cord Guard 45 1 Tank Cover 14 1 Seal Ring
Streszczenie treści zawartej na stronie nr. 12
MAKlTA LIMITED ONE YEAR WARRANTY I Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or mat
