Streszczenie treści zawartej na stronie nr. 1
ORDER NO. MAC060503U
E4
ServiceManual
Commercial Vacuum Cleaner
MC-V5203
SPECIFICATIONS
Model MC-V5203
Power Source AC 120V (60 Hz)
Power Consumption 10.0 Amps
Cord Length 50 Ft.
Motor Protector Yes
PANASONIC CONSUMER ELECTRONICS
PANASONIC SALES COMPANY, DIVISION
Height Adjust Automatic
OF MATSUSHITA ELECTRIC OF
COMPANY, DIVISION OF MATSUSHITA
PUERTO RICO INC. (“PSC”)
ELECTRIC CORPORATION OF AMERICA
Weight 17 lbs.
Ave. 65 de Infanteria, Km. 9.5
One Panasonic Way
San Gabriel Industrial Park
Sec
Streszczenie treści zawartej na stronie nr. 2
NOTES WARNING This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or products dealt with in this service information by anyone else coul
Streszczenie treści zawartej na stronie nr. 3
NOTES SCHEMATIC DIAGRAM NOTE: For general servicing, it is necessary to eliminate pinching of any wire during reassembly. After servicing any electrical component or electrical enclosure, the unit should be reassembled and checked for dielectric breakdown or current leakage. WIRING MANAGEMENT DRAWING NOTE: Do not pinch any wires during reassembly. After servicing any electrical component or electrical enclosure, the unit should be reassembled and checked for dielectric breakdown or current lea
Streszczenie treści zawartej na stronie nr. 4
A (NOZZLE HOUSING)… BLOCK EXPLODED VIEW MOTOR FAN REPLACEMENT Removal Tap Down on the A-5 A-19 3 Crimped Areas 1. Mark the position of the fan case's location on the motor with a pencil, or score it with a sharp object before disassembly. This will aid you in reassembling the fan case, (Fig. 21). A-3 A-6 A-1 2. The fan case has three (3) crimped sections on it to hold the case onto the motor. These A-2 A-6 will have to be straightened by using a pair of needle nose pliers and by tapping ou
Streszczenie treści zawartej na stronie nr. 5
A MOTOR REPLACEMENT PARTS LIST (NOZZLE HOUSING)… BLOCK Removal Screws 1. Remove the dust cover by grasping the top near the ON/OFF switch and pulling Motor Case Ref. No. Part Name & Description Part No. Quantity Remarks sharply out toward you. A - 1 Nozzle Housing ACØ1ACCAZUU3 1 A - 2 Window AC21HAFVZUØ3 1 2. Remove the lower plate, agitator assembly, belt, the plastic shaft, and the nozzle A - 3 Plastic Shaft AMC25S-VØØ 1 housing as instructed in the respective removal sections. A - 4 Fu
Streszczenie treści zawartej na stronie nr. 6
C (BODY, MOTOR HOUSING, AND MOTOR)… BLOCK EXPLODED VIEW POWER CORD/ON-OFF SWITCH REPLACEMENT (Cont.) Installation 1. Insert the new power cord (power cord replacement only) into the dust compartment as far as necessary in order to place a new cord retainer in proper location on power cord. The proper location is approximately one and one eighth inches/thirty millimeters (1 1/8”/30 mm) of new power cord yellow outer jacket extending past the cord retainer and washer. The washer goes bet
Streszczenie treści zawartej na stronie nr. 7
C (MOTOR HOUSING, MOTOR, HANDLE, AND BODY)... BLOCK SWITCH COVER AREA WIRING MANAGEMENT PARTS LIST Ref. No. Part Name & Description Part No. Quantity Remarks To Plug End C-1 Dust Container, Machined AC88KAPNZV17 1 (Includes C-38, C-44, C-45, C-46, C-47, C-48) Power Cord C-2 Switch, ON/OFF AMC98E-VØØØU 1 (Includes C-38, C-46) (With Yellow Outer Jacket) C-3 Power Cord AC94EAPNZYØ2 1 (Includes C-38, C-44, C-45, C-46) C-4 Wire Nut AMC-1CTCE23 4 C-5 Packing Dust Container AC66KVØ1VØ6 2 Cord Wir
Streszczenie treści zawartej na stronie nr. 8
(MOTOR FAN ASSEMBLY) EXPLODED VIEW NOZZLE HOUSING AND SHORT HOSE REPLACEMENT Removal 1. Remove the lower plate as outlined in the LOWER PLATE REMOVAL/INSTALLATION section. 1 2. Remove the belt and agitator assembly as outlined in the respective sections. 2 3 3. Remove the nozzle hose by pulling it up out of the nozzle housing and then pulling it, while twisting, out of 4 the wand holder. (Fig. 10) 4. Insert a flat blade screwdriver between the nozzle 5 housing and the plastic shaft, pry out the
Streszczenie treści zawartej na stronie nr. 9
(PACKAGING) BRUSH REPLACEMENT EXPLODED VIEW When to replace brushes 1. The agitator brushes should be replaced when they are worn. Brushes should be checked by holding a card across the lower plate, (Fig. 5). If the bristles on the agitator assembly do not touch the card you should replace all the brushes for best cleaning results. Removal NOTE: Use extreme care when prying or depressing these items with a screwdriver in b order to help prevent personal injury or damage to the vacuum. Be carefu
Streszczenie treści zawartej na stronie nr. 10
LOWER PLATE REMOVAL/INSTALLATION AGITATOR ASSEMBLY REMOVAL/INSTALLATION Removal Removal 1. Place the handle in the upright position. The brushes are replaceable separately. When the brushes need replacing, the agitator assembly will have to be removed. 2. Turn the vacuum cleaner over exposing the underside. Release the lower plate by pressing inward the two (2) latches and depressing the two locking 1. Remove the lower plate as outlined in the LOWER PLATE REMOVAL/ tabs that secure the lower plat
