Streszczenie treści zawartej na stronie nr. 15
General operations Reset the unit Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press OPEN button on the panel to open the panel and press RESET button to restore the unit to the original factory settings. Power button Press any button on the panel (except OPEN button) or STANDBY button on the RC to turn on the unit. Press and hold PWR/MUTE button on the panel or STANDBY button on the RC to switch the unit off. Note: After the unit is off, the
Streszczenie treści zawartej na stronie nr. 16
Setting other characteristics During TUNER mode press SEL button and hold for 2 seconds, shortly and repeatedly press SEL button to select the setting: TA SEEK => PI MUTE => RETUNE L => MASK DPI =>TA VOL => EON TA => DISP REV => BEEP. To adjust the selected setting, rotate VOL knob or press VOL+/- buttons on the RC. TA SEEK/TA ALARM In TA SEEK mode, the unit will seek for traffic announcement program when TA is pressed; in TA ALARM mode, no TA/TP is displayed and the alarm is set off. After choo
Streszczenie treści zawartej na stronie nr. 17
Turning the sound off Press MUTE button on the RC or PWR/MUTE button on the unit to turn the sound off. Press it again or press VOL+/- buttons on the RC or rotate VOL knob on the panel to turn the sound on. Mode setting Press MODE/REJECT CALL button on the panel or MODE button on the RC repeatedly to select: TUNER => DVD (if inserted) => USB (if USB device is inserted) => SD (if the flash card is inserted) => AUX. Equalizer setting Press and hold TA/DSP button on the unit or press DSP button on
Streszczenie treści zawartej na stronie nr. 18
Digital tuner operations Note: RDS (Radio Data System) service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available, either. RDS overview PI: Program Identification Code – for identifying code. PS: Program Service Name Broadcast – station name data expressed in alphanumerically character. TP: Traffic Program Identification – for traffic information broadcasting station. TA: Traffic Announcement Identification – show
Streszczenie treści zawartej na stronie nr. 19
- Hold a preset button (1-6), which you want store the station for at least 2 seconds. To recall a station: - Select a band (if needed) - Press a preset button (1-6) briefly to recall the stored station. AF/MONO button Press AF/MONO button to enable AF mode. Press and hold AF/MONO on the unit or press ST/MO on the RC to choose MONO or STEREO. Auto memory store Select a band. Press AS/PS button on the panel or P.SCN/RPT button on the RC and hold for 2 seconds to enter auto store mode. The radio
Streszczenie treści zawartej na stronie nr. 20
The RDS program will be automatically searched and received. After turning on, if the RDS signal is weak or even no signal, the unit will search another frequency with this RDS program. Default setting is ON. PTY (Program Type) function 1. Press PTY/SCN button on the panel or press PROG/PTY button on the RC to select the program type group: MUSIC GROUP => twice to select SPEECH GROUP => PTY OFF. 2. When the program type is selected press digit buttons (1~6) repeatedly to select the program type
Streszczenie treści zawartej na stronie nr. 1
H-CMD7086
DVD/CD/MP3 RECEIVER WITH BLUETOOTH
DVD/CD/MP3- C BLUETOOTH
Instruction manual
Streszczenie treści zawartej na stronie nr. 2
Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future. Table of contents Table of contents ...............................................................................................................................................2 Important safeguards .....................................................................
Streszczenie treści zawartej na stronie nr. 3
Important safeguards Read carefully through this manual to familiarize yourself with this high-quality sound system. The beginning of operation is the moment of the unit installation. Before use the device in winter it is recommended to heat up the passenger compartment during 20 seconds or to the operation temperature. Use the unit with the temperature that goes beyond the operation temperature greatly decreases the operation resource of the screen and other components of device and can resu
Streszczenie treści zawartej na stronie nr. 4
Accessories Receiver 1 pc Remote controller 1 pc Panel protective case 1 pc AV cable 1 pc USB cable 1 pc ISO cable 1 pc Mounting parts: Release keys 2 pc Screw 20 1 pc Bolt 6 4 pc Washer 2 pc Nut 1 pc Mounting strap 1 pc Rubber 1 pc Consumer information 1 pc Warranty card 1 pc Instruction manual 1 pc 4
Streszczenie treści zawartej na stronie nr. 5
Installation/connection Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Before finally installing the unit, connect the wiring and make sure that the unit works properly. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop.
Streszczenie treści zawartej na stronie nr. 6
1. Install the sleeve into the dashboard; ensure it is installed with the correct side and there are no obstacles (wires, dashboard elements, etc) for the unit installation. 2. After installing the sleeve into the dashboard, bend tabs fitting to the size of the dashboard to fix the sleeve in place. 3. Use the metal strap to fix the rear side of the unit. Determine a place for fixing and install the strap as shown in the picture. You can bend the strap to the needed angle with your hands. 4. Make
Streszczenie treści zawartej na stronie nr. 7
Trim frame installation To install the trim frame, press it to the unit body and push it to fix it in place. This should be done before installing the front panel; otherwise you are not able to install the trim frame. When the trim frame being installed, the side with the groove should face down and fixed first. 2. DIN REAR-MOUNT (Method B) For this method, use the screw holes in the lateral sides of the unit. Fix the unit with the help of the factory radio mounting brackets. 1. Select a positio
Streszczenie treści zawartej na stronie nr. 8
Attaching the control panel 1. Insert the right side of the control panel into the main unit (pic. 3). 2. Press the control panel on to the left side of middle of it until a “click” sound is heard (pic. 4). Pic. 4 Pic. 3 Caution: Do not insert the control panel from the left side. It can damage the control panel. The control panel can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. The rear connector t
Streszczenie treści zawartej na stronie nr. 9
Electrical connection Caution: For some car models you may need to modify wiring of the supplied power cord. Contact your authorized car dealer before installing this unit. Notes: 2 cable is connected to a Hands-Free device (not included). 9
Streszczenie treści zawartej na stronie nr. 10
The parking wire is connected with brake signal; for safety, the programs can be seen on the monitor after braking the car. 10
Streszczenie treści zawartej na stronie nr. 11
Panel controls Front panel 1. PWR/MUTE button 2. OPEN button 3. SD/MMC card slot 4. DISC slot 5. EJECT button 6. USB jack 7. AV IN 8. MODE/REJECT CALL button 9. ACCEPT CALL button 10. DIS/DUAL button 11. VOL KNOB/SEL button 12. TA/DSP button 13. PTY/SCAN button 14. AF/MONO button 15. BAND/LOUD button 16. NEXT button 17. PREVIOUS button 18. AS/PS button 19. 1/PLAY/PAUSE button 20. 2/REPEAT button 21. 3/INTRO button 22. 4/RANDOM button 11
Streszczenie treści zawartej na stronie nr. 12
23. 5/ DIR- button Inner panel 24. 6/DIR+ button 25. IR remote control sensor 26. Microphone 27. Panel status indicator 28. RESET button 12
Streszczenie treści zawartej na stronie nr. 13
Remote control 1. DISP/DUAL button 2. STANDBY button 3. OSD button 4. ST/MO button 5. SETUP button 6. ENTER button 7. PREVIOUS/NEXT button 8. ANGLE button 9. VOL- button 10. SEL button 11. BAND/RDM button 12. AUDIO/GOTO button 13. Number buttons 14. ACCEPT CALL/T-MENU button 15. TITLE button 16. DSP button 17. MODE button 18. MUTE button 19. MENU button 20. Cursor buttons (LEFT, RIGHT, UP, DOWN) 21. PLAY/PAUSE button 22. INT button 25. A-B/ZOOM button 28. P.SCN/RPT button 23. VOL+ button 26. SUB
Streszczenie treści zawartej na stronie nr. 14
Changing the battery 1. Pull out the battery tray. Insert the 1 x lithium battery, type CR 2025 3V battery with the stamped (+) mark facing upward. 2. Insert the battery tray into the remote control. Warning: Store the battery where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately. Do not recharge, short, disassemble or heat the battery or dispose it in a fire. Do not expose or bring into contact the battery with other metallic materials. Doing
