Streszczenie treści zawartej na stronie nr. 1
Bottom Mount No Frost
Refrigerator
Refrigerateur
Sans Gel Monte
de Dessous
Refrigerador
de Montaje Inferior Sin
Escarcha
User Manual-
Model #
HBE18
Guide de l’Utilisateur-
Modèle
HBP18
Manual del Usuario-
Para Modelo de
HBQ18
Streszczenie treści zawartej na stronie nr. 2
English SAFETY PRECAUTIONS Read all of the instructions before using this appliance. When using this appliance, always exercise basic safety precautions, including the fol- lowing: 1) Use this appliance only foe its intended purpose as described in this use and care guide. 2) This refrigerator must be properly installed in accordance with the installation instructions before it is used. See grounding instructions in the installation section. 3) Never unplug your refrigerator by pulling on the po
Streszczenie treści zawartej na stronie nr. 3
English 10) This refrigerator should not be recessed or built-in an enclosed cabinet. It is designed for freestanding installation only. 11) Do not operate your refrigerator in the presence of explosive fumes. SAVE THESE INSTRUCTIONS For Future Reference DANGER Risk of child entrapment. Before you throw away your old refrigerator or freezer, take off the doors. Leave the shelves in place so that children may not easily climb inside. As per UL 250 Standards Thank you for using our Haier product
Streszczenie treści zawartej na stronie nr. 4
English Table of Contents PAGE Safety Precautions ..........................................................................1 Parts And Features ..........................................................................4 Installing Your Refrigerator............................................................5 Unpacking Your Refrigerator ..................................................................5 Adjusting Your Refrigerator .................................................................
Streszczenie treści zawartej na stronie nr. 5
English Parts And Features Picture for illustration purpose only Features and quantities may vary per model 1. Refrigerator Light 12. Wire Basket 2. Refrigerator Control 13. Base Grille 3. Half-Width Glass Shelf 14. Dairy Bin 4. Deli Drawer 15. Egg Bin 5. Crisper Cover 16. Door Storage Bin 6. See-Through Crisper Drawers 17. Bin Door Shelf 7. Ice Tray 18. Tilt-out Wire Door Shelf 8. Freezer Control 19. Door Handle 9. Freezer Light 20. Freezer Door Hinge Cover 10. Ice Storage Container 21. Adjusta
Streszczenie treści zawartej na stronie nr. 6
English Installing Your Refrigerator Unpacking Your Refrigerator 1. Remove all packaging material. This includes the foam base, all adhesive tape holding, refrigerator accessories inside and outside, and the plastic stoppers holding the shelves. Slide out and remove plastic or foam guard used to secure the compressor from shipping damage due to vibration and shock. 2. Inspect and remove any remains of packing, tape or printed materials before powering on the refrigerator. Adjusting Your Refrige
Streszczenie treści zawartej na stronie nr. 7
English Electrical Requirement • Make sure there is a suitable power Outlet (115 volts, 15 amps outlet) with proper grounding to power the refrigerator. • Avoid the use of three plug adapters or cutting off the third grounding in order to accommodate a two plug outlet. This is a dangerous practice since it provides no effective grounding for the refrigerator and may result in shock hazard. Use of Extension Cords • Avoid the use of an extension cord because of potential safety hazards under cert
Streszczenie treści zawartej na stronie nr. 8
English Door Handle Installation Handle Installation of Refrigerator Door: 1. Take out door handle, screws and screw covers from refrigerator accessory bag. 2. Align the upper part of door handle with the screw hole of the upper edge of refrigerator door, and fix them by screws. 3. Align the lower screw holes of the door handle with the holes in the refrigerator door, fix them with screws, and cover them with screw covers. fig. #1 Handle installation of freezer door: 1. Take out door handle, scr
Streszczenie treści zawartej na stronie nr. 9
English Door Alignment (see fig. # 3) 1. Remove refrigerator door hinge cover screw. 2. Remove the top hinge cover. 3. Loosen the top hinge screws using a Phillips head screwdriver. 4. Adjust the door or put a spacer in between and then tighten the screws. 5. Replace the top hinge cover. Reversing the Door Swing Left/right door opening method: This product provides the reversing of the left/right door opening. You can select your preference of door opening by following the procedure to make the
Streszczenie treści zawartej na stronie nr. 10
English Dismantling: (see fig. # 4) 1. Fix refrigerator and freezer door by sticking adhesive tape on both side to hold doors in place. 2. As shown in fig.3, dismantle the hinge box cover on the upper part of refrigerator door with a Phillips head screwdriver. Then remove the two screws from the hinge. Take out the hinge by pulling it vertically, and keep it in a safe place. 3. Remove the adhesive tape on refrigerator door, lift and take the door down, and carefully put it aside. 4. As shown in
Streszczenie treści zawartej na stronie nr. 11
English Reinstallation: (see fig. #5 and #6) 1. Press and pull out the hinge cover from the hinge. 2. Before dismantling the lower hinge, remove the hinge axle and fix it on the opposite hole. As shown in fig.5, dismantle the lower hinge, and then install them on the left side. 3. Remove the door stop plate from the bottom of the door and put it on the opposite side of the door. 4. Install freezer door: make the left bottom hole of the freezer compartment door fall over the lower hinge axle, mo
Streszczenie treści zawartej na stronie nr. 12
English Reversing the Door Handles Refrigerator: (see fig. #7) 1. Remove screw cover from the handles. 2. Using a Phillips head screwdriver, remove the inside screw and both the screws at the bottom of the freezer door that holds the handle. 3. Install the handle on the opposite side. 4. Remove screw plugs. 5. Install the screws and the screw cover on their corresponding position. fig. # 7 11
Streszczenie treści zawartej na stronie nr. 13
English Refrigerator Features And Use Setting the Controls: Adjusting Control Settings For your convenience, your Give the refrigerator time to cool down refrigerator controls are preset completely before adding food. It is best at the factory. When you first to wait 24 hours before you put food install your refrigerator, make into the refrigerator. The settings indicat- sure that the controls are still ed in the previous section should be cor- preset. The Refrigerator Control rect for normal ho
Streszczenie treści zawartej na stronie nr. 14
English Refrigerator Interior Shelves The refrigerator shelves of your refrigerator were designed with you in mind. Their varied adjustability allows you to satisfy your personal storage needs. Your model may have wire, glass, or no spill glass shelves. Your model may have full-width or half-width shelves. Only your model pur- chase and your imagination limit the possibilities. To remove glide-out shelf: (see fig.#8) 1. Gently pull out the shelf until the shelf has been completely removed. fig.
Streszczenie treści zawartej na stronie nr. 15
English To replace a full-width or half-width cantilevered shelf: (see fig.#9) 1. Guide the rear shelf hooks into the desired slots in the metal shelf supports located on the back refrigerator wall. 2. Tilt up front of the shelf to set the shelf hooks in place. 3. Lower the front of the shelf into position until the rear hooks lock into the slots of the metal shelf supports. fig. # 9 Utility Drawer and Cover To remove the utility drawer: (see fig.#10) 1. Slide utility drawer out until it reaches
Streszczenie treści zawartej na stronie nr. 16
English To install utility drawer cover shelf: (see fig.#11) 1. Guide the rear shelf hooks into the desired slots in the metal shelf sup- ports located on the back refrigerator wall. 2. Tilt up front of the shelf to set the shelf hooks in place. 3. Lower the front of the shelf into position until the rear hooks lock into the slots of the metal shelf supports. fig. # 11 Crisper and Crisper Cover To remove and install the crisper: (see fig.#12) 1. Slide crisper straight out to the stop. 2. Gently
Streszczenie treści zawartej na stronie nr. 17
English To remove the crisper cover: (see fig.#13) 1. First remove both crispers (see page 15). 2. Gently push upward from the underside of the crisper cover to remove it from the crisper cover frame. 3. Carefully grasp the crisper cover and slide out to remove. 4. Lift crisper cover frame up and remove. fig. # 13 To replace the crisper cover: (see fig.#13) 1. Insert the rear of the crisper cover frame into the support bracket the sidewalls of the refrigerator. 2. Lower the front of the crisper
Streszczenie treści zawartej na stronie nr. 18
English • LOW setting allows moist air to exit the crisper for optimum storage of fruits and/or vegetables, which have skins. • HIGH setting retains moist air in the crisper for optimum storage of fresh, leafy vegetables. fig. # 14 Refrigerator Door Shelves Gallon door storage: (see fig.#15) Your refrigerator may be equipped with gallon door storage shelves. This feature will allow for the storage of gallon size containers. To remove refrigerator door shelves: (see fig.#15) 1. Remove all items s
Streszczenie treści zawartej na stronie nr. 19
English To adjust the door shelf bottle huggers: (see fig.#16) 1. Grasp the hugger firmly and slide right or left until it is snug against the items stored on the shelf. fig. # 16 Freezer Features Ice Service Rack Install ice service rack by placing ice service rack on washers and sliding down. 18
Streszczenie treści zawartej na stronie nr. 20
English Slide-out Shelf: Slide out shelf pulls forward for easy access to items in back. • Remove slide-out shelf by sliding forward until ballpoint beneath center rail catches in molding groove. • Grasp shelf by center rail, pull up, and remove. • Slide in until ballpoint falls into molding groove. fig. # 17 Vertical Shelf Divider Install vertical shelf divider by competing the following steps: 1. Slide prongs of shelf divider beneath desired grill work, slightly off-cen- ter from center rail.
