Streszczenie treści zawartej na stronie nr. 1
WASHER INSTALLATION INSTRUCTIONS
Table of Contents
WASHER SAFETY............................................ 1
INSTALLATION REQUIREMENTS ................. 2
Tools and Parts ............................................. 2
Location Requirements................................. 2
Drain System................................................. 3
Electrical Requirements ................................ 3
INSTALLATION INSTRUCTIONS ................... 4
Before You Start...................................
Streszczenie treści zawartej na stronie nr. 2
INSTALLATION REQUIREMENTS Alternate Parts Your installation may require additional parts. For information on Tools and Parts ordering, please refer to the toll-free phone numbers on the front Gather the required tools and parts before starting installation. page of the Washer User Instructions. The parts supplied are in the washer basket. If You Have: You Will Need to Buy: Tools needed for connecting the drain hose and water inlet hoses: Laundry tub or Sump pump system (if not already s
Streszczenie treści zawartej na stronie nr. 3
Recessed area or closet installation Laundry tub drain system (view C) The dimensions shown are for the recommended spacing allowed The laundry tub needs a minimum 76 L (20 gal.) capacity. The top (A and B), except the closet door ventilation openings. The of the laundry tub must be at least 99 cm (39") above the floor and dimensions shown for the closet door ventilation openings (C) are no higher than 244 cm (96") from the bottom of the washer. the minimum required. Floor drain system (view
Streszczenie treści zawartej na stronie nr. 4
To minimize possible shock hazard, the cord must be plugged into a mating, earthing-type outlet, earthed in accordance with EARTHING INSTRUCTIONS local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer For an earthed, cord-connected washer: to have the properly earthed outlet installed by a qualified This washer must be earthed. In the event of a malfunction electrician. or breakdown, earthing will reduce the risk
Streszczenie treści zawartej na stronie nr. 5
2. Firmly grasp the power cord and pull to completely remove 2. Check that two (2) cotter pins were removed with the shipping the power cord, cord restraint, and pin from the rear panel. strap. 3. Confirm that the power cord restraint (A), and pin (B) are removed. Connect Drain Hose Proper connection of the drain hose protects your floors from damage due to water leakage. Read and follow these instructions. The drain hose is connected to your washer and is stored inside the washer cabine
Streszczenie treści zawartej na stronie nr. 6
To keep drain water from going back into the washer: Check the temperature of the water to make sure that the hot water hose is connected to the hot water faucet and that the Do not force excess drain hose into standpipe. Hose should cold water hose is connected to the cold water faucet. be secure but loose enough to provide a gap for air. Do not lay excess hose on the bottom of the laundry tub. Floor drain Do not install the drain hose form on to the corrugated drain hose. You may nee
Streszczenie treści zawartej na stronie nr. 7
5. Attach the cold water hose to the top inlet valve. 6. Screw on coupling by hand until it is seated on the washer. Level the Washer 7. Using pliers, tighten the couplings with an additional Properly leveling your washer avoids excessive noise and two-thirds turn. vibration. NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result. Install the Front Leveling Feet Check for leaks 1. Prop up the front of the washer about 10.2 cm (4") with a wood block
Streszczenie treści zawartej na stronie nr. 8
5. After the washer is in its final location and level, use a 14 mm Steps in Final Location or ⁹⁄₁₆" open-end wrench to turn the nuts counterclockwise on the feet tightly against the washer cabinet. 1. Slide the washer to its final location. IMPORTANT: If the nuts are not tight against the washer 2. Tilt the washer forward until the rear of the washer is at least cabinet, the washer may vibrate. 10.2 cm (4") off the floor. You may hear the self-adjusting rear feet click into place. Lower t
