Streszczenie treści zawartej na stronie nr. 1
WASHER INSTALLATION INSTRUCTIONS
Table of Contents
WASHER SAFETY............................................ 1
INSTALLATION REQUIREMENTS ................. 2
Tools and Parts ............................................. 2
Location Requirements................................. 2
Drain System................................................. 3
Electrical Requirements ................................ 3
INSTALLATION INSTRUCTIONS ................... 4
Before You Start...................................
Streszczenie treści zawartej na stronie nr. 2
INSTALLATION REQUIREMENTS Alternate Parts Your installation may require additional parts. For information on Tools and Parts ordering, please refer to the toll-free phone numbers on the front Gather the required tools and parts before starting installation. page of the Washer User Instructions. The parts supplied are in the washer basket. If You Have: You Will Need to Buy: Tools needed for connecting the drain hose and water inlet hoses: Laundry tub or Sump pump system (if not already s
Streszczenie treści zawartej na stronie nr. 3
Recessed area or closet installation Laundry tub drain system (view C) The dimensions shown are for the recommended spacing allowed The laundry tub needs a minimum 76 L (20 gal.) capacity. The top (A and B), except the closet door ventilation openings. The of the laundry tub must be at least 99 cm (39") above the floor and dimensions shown for the closet door ventilation openings (C) are no higher than 244 cm (96") from the bottom of the washer. the minimum required. Floor drain system (view
Streszczenie treści zawartej na stronie nr. 4
To minimize possible shock hazard, the cord must be plugged into a mating, earthing-type outlet, earthed in accordance with EARTHING INSTRUCTIONS local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer For an earthed, cord-connected washer: to have the properly earthed outlet installed by a qualified This washer must be earthed. In the event of a malfunction electrician. or breakdown, earthing will reduce the risk
Streszczenie treści zawartej na stronie nr. 5
2. Firmly grasp the power cord and pull to completely remove 2. Check that two (2) cotter pins were removed with the shipping the power cord, cord restraint, and pin from the rear panel. strap. 3. Confirm that the power cord restraint (A), and pin (B) are removed. Connect Drain Hose Proper connection of the drain hose protects your floors from damage due to water leakage. Read and follow these instructions. The drain hose is connected to your washer and is stored inside the washer cabine
Streszczenie treści zawartej na stronie nr. 6
Then slide the second hose clamp onto coupling. Insert end of adapter into coupling. Use a screwdriver to install second Clear the water lines hose clamp over coupling. 1. Run water through both faucets and inlet hoses, into a laundry tub, drainpipe or bucket, to get rid of particles in the water lines that might clog the inlet valve screens. 2. Check the temperature of the water to make sure that the hot water hose is connected to the hot water faucet and that the cold water hose is con
Streszczenie treści zawartej na stronie nr. 7
NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result. Level the Washer Properly leveling your washer avoids excessive noise and vibration. Install the Front Leveling Feet 1. Prop up the front of the washer about 10.2 cm (4") with a wood block or similar object. The block needs to support the weight of the washer. 5. Attach the cold water hose to the top inlet valve. 6. Screw on coupling by hand until it is seated on the washer. 7. Using pliers,
Streszczenie treści zawartej na stronie nr. 8
2. Tilt the washer forward until the rear of the washer is at least 10.2 cm (4") off the floor. You may hear the self-adjusting rear Complete Installation feet click into place. Lower the washer to the floor. 1. Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended earthing method. See “Electrical Requirements.” 2. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.
