Streszczenie treści zawartej na stronie nr. 1
INSTALLATION INSTRUCTION MANUAL for
Bosch Electric Built-in Single & Double Oven
Models HBL 73../74../75../76.. and Models HBN 74../75../76..
BEFORE YOU BEGIN, READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY
IMPORTANT: Save these instructions for the local electrical inspector’s use.
INSTALLER: Please leave this manual with owner for future reference.
OWNER: Please keep this manual for future reference.
VEUILLEZ LIRE ATTENTIVEMENT CE MANUEL AVANT DE COMMENCER L’INSTALLATION
IMPORTANT: Conserv
Streszczenie treści zawartej na stronie nr. 2
Table Of Contents Introduction .............................................................................................................. 3 Tools You Will Need ........................................................................................... 3 Power Requirements ........................................................................................... 3 Choosing Oven Location .................................................................................... 3 Steps For Installat
Streszczenie treści zawartej na stronie nr. 3
INTRODUCTION POWER REQUIREMENTS The oven must be supplied with the proper volt- Please read these instructions COMPLETELY age and frequency. The oven is manufactured to be AND CAREFULLY. They will save you time and connected to a three-wire or four-wire, single phase, effort and help to ensure optimum oven performance. 240 Volt, 60 Hz AC electrical supply on a separate Be sure to observe all WARNINGS. circuit fused on both sides of the line. If a 208 Volt These installation instructions are inte
Streszczenie treści zawartej na stronie nr. 4
22" depth 22" depth TECHNICAL DATA for HBL 73../74../75../76.. SINGLE OVEN For cutout dimensions see following section titled: Preparing Location Electrical Ratings and Maximum Connected Load Single Oven Amperes Watts Convection Models Volts Hertz @240V/208V @240V/208V Oven HBL 732A UC 240/208 60 15.4/17.2 3,600/3,500 No HBL 735A UC 240/208 60 15.4/17.2 3,600/3,500 No HBL 736A UC 240/208 60 15.4/17.2 3,600/3,500 No HBL 742A UC 240/208 60 15.8/17.6 3,650/3,550 Yes HBL 745A UC 240/208 60 15.8/17.6
Streszczenie treści zawartej na stronie nr. 5
22" depth 22" depth TECHNICAL DATA for HBN 74../75../76.. SINGLE OVEN For cutout dimensions see following section titled: Preparing Location Electrical Ratings and Maximum Connected Load Single Oven Amperes Watts Convection Models Volts Hertz @240V/208V @240V/208V Oven HBN 742A UC 240/208 60 15.8/17.6 3,650/3,550 Yes HBN 745A UC 240/208 60 15.8/17.6 3,650/3,550 Yes HBN 746A UC 240/208 60 15.8/17.6 3,650/3,550 Yes SINGLE OVEN DOUBLE OVEN DOUBLE OVEN For cutout dimensions see following section ti
Streszczenie treści zawartej na stronie nr. 6
UNDERCOUNTER INSTALLATION, SINGLE OVEN Oven electrical supply: Locate junction box in adjacent cabinet or below bottom support surface. HBL Models: 28" opening width HBN Models: 25-3/8" opening width Bottom support surface must be solid, level and able to support at least 150 lbs. 1/4" min. distance between oven door frame and adjacent doors or drawer fronts. Toe space area HBL Models: 29-1/4" width of oven door frame HBN Models: 26-5/8" width of oven door frame NOTE: Decorative inserts must mai
Streszczenie treści zawartej na stronie nr. 7
22" depth 24" opening depth WALL INSTALLATION, SINGLE OVEN Electrical supply junction box * HBL: HBL 73../74../75../76.. * HBN: HBN 74../75../76.. Secure oven to cabinet using the screws provided. Screws should be inserted through the mounting holes in the positions indicated in the frame (open door to see frame and mounting holes). Do not overtighten screws. 6. Be careful when placing oven. DO NOT Note: 1. Do not slide oven across floor. Damage pinch the conduit between the oven back to floor c
Streszczenie treści zawartej na stronie nr. 8
22" depth 24" opening depth WALL INSTALLATION, DOUBLE OVEN Electrical supply junction box * HBL: HBL 73../74../75../76.. * HBN: HBN 74../75../76.. Secure oven to cabinet using the screws provided. Screws should be in- serted through the mounting holes in the positions indicated in the frame (open door to see frame and mounting holes). Do not overtighten screws. Note: 1. Do not slide oven across floor. Damage 6. Be careful when placing oven. DO NOT to floor covering or floor could result. pinch t
Streszczenie treści zawartej na stronie nr. 9
WIRING REQUIREMENTS ELECTRICAL SUPPLY When making the wire connections, use the en- Before installing the oven have a qualified elec- tire length of the conduit provided (3 feet). The con- trician verify that your home is provided with ad- duit must not be cut. equate electrical service and that the addition of the Before making connections make sure the power oven will not overload the branch circuit on which is off and read and observe the following: it is to be installed. A separate three-wir
Streszczenie treści zawartej na stronie nr. 10
In Canada: CONNECTING TO 208 VOLT CIRCUIT This option is provided for areas where standard Wiring must conform to Canadian Electrical Code C22.1- latest edition. 240 Volt service is not available. This option must You can obtain a copy of the Canadian Electrical be accessed with the oven connected to power source, with the oven door (upper oven in double Code by writing: oven) open, and using the following sequence: Canadian Standards Association 178 Rexdale Boulevard 1. Touch CANCEL pad. Rexdal
Streszczenie treści zawartej na stronie nr. 11
ELECTRICAL CONNECTIONS This appliance is manufactured with a green GROUND wire connected to the oven chassis. After making sure that the power has been turned off, connect the flexible conduit from the oven to the junction box using a U.L. listed conduit connector. Figures A and B and the instructions provided below present the most common way of connecting the ovens. Your local codes and ordinances, of course, take precedence to these instructions. Complete electrical connections according to l
Streszczenie treści zawartej na stronie nr. 12
4. Set the clock by following these steps: FINAL CHECKLIST a). Touch TIME pad. To prevent improper connections leading to dam- b). Turn rotary knob clockwise until CLOCK age of electrical components and so voiding the appears. warranty, the following steps must be performed: c). Touch TIME pad. d). Turn rotary knob in either direction. The 1. Check the electrical requirements and make sure time displayed will change in 10-minute in- you have the correct electrical supply and that crements and in
