Streszczenie treści zawartej na stronie nr. 1
LAP30EULBA
LAP30EULFR
NOTEBOOK CART ASSEMBLY
WITH TIMER
Assembly Instructions for:
LAP30EULBA
INTERIOR E-UNIT
REPOSITIONING / REPLACEMENT
CAUTION: RISK OF ELECTRICAL SHOCK.
AND
DO NOT PLUG INTO ANOTHER
RELOCATABLE POWER TAP.
TIMER REPLACEMENT
Parts List
Qty. Part No. Description
NO TV/MONITOR TO BE
1 LAP30EULBA Cart Assembly, e-units at back
USED ON TOP OF CART
LAP30EULFR Cart Assembly, e-units at front
Tools Required
MAXIMUM WEIGHT OF ACCESSORIES
Philips screwdriver ON TOP OF CART: 25 LBS.
Th
Streszczenie treści zawartej na stronie nr. 2
E-Unit power timer assembly cord bottom shelf Front View bracket assembly bracket DETAIL 'B' assembly clip DETAIL 'A'
Streszczenie treści zawartej na stronie nr. 3
front-left front-right Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. DETAIL 'C' Step 3 Remove 18 screws (2 per shelf) from rear panel that secure the 9 interior shelves (see DETAIL 'C').
Streszczenie treści zawartej na stronie nr. 4
mounting tab DETAIL 'D' Step 4 Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D', then carefully sliding out. Set each shelf aside.
Streszczenie treści zawartej na stronie nr. 5
cutout window clip-rear Step 5 Reinstall the E-Units (set aside from being removed from the front) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to the rear of cart. 3. Tilt in and set bottom in back, in front of rear panel cutout window. 4. Grip the top and tilt to the upright position, underneath top panel bracket. When repositioned correctly, the E-Unit power switch should be visible from rear panel cutout window. Reinstall the E-Unit bracket assemblies
Streszczenie treści zawartej na stronie nr. 6
tab notch Step 6 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DETAIL 'E' Step 7 Reinstall 18 screws to rear panel that will secure the 9 interior shelves (see DETAIL 'E). DO NOT OVER TIGHTEN SCREWS. Installation is now complete and ready for
Streszczenie treści zawartej na stronie nr. 7
NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE STARTING E-UNIT REPOSITIONING: 'REAR TO FRONT' DETAIL 'A' Step 1 Remove 18 screws (2 per shelf) from rear panel that secure the 9 interior shelves (see DETAIL 'A'). mounting tab DETAIL 'B'
Streszczenie treści zawartej na stronie nr. 8
Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View Carefully unplug the power cords of the E-Units from the timer assembly (see Front View) and unclip the power cords from the clips at the rear of cart. Loosen the screw holding the E-Unit bracket assembly and remove all 4 bracket assemblies (see DETAILS 'C' and
Streszczenie treści zawartej na stronie nr. 9
DETAIL 'C' DETAIL 'D' rear-left rear-right Step 3 Remove rear-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. Remove rear-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside.
Streszczenie treści zawartej na stronie nr. 10
notch tab Step 4 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DETAIL 'F' Step 5 Reinstall 18 screws to rear panel that will secure the 9 interior shelves (see DETAIL 'F'). DO NOT OVER TIGHTEN SCREWS.
Streszczenie treści zawartej na stronie nr. 11
offset clip Step 6 Reinstall the E-Units (set aside from being removed from the rear) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to the front of cart. 3. Tilt in and set against offset of bottom panel (of cart). 4. Grip the top and tilt to the upright position. When repositioned correctly, the E-Unit power switch should face the front. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the bra
Streszczenie treści zawartej na stronie nr. 12
NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE STARTING E-UNIT REPLACEMENT: 'REAR LOCATION' DETAIL 'A' Step 1 Remove 18 screws (2 per shelf) from rear panel that secure the 9 interior shelves (see DETAIL 'A'). mounting tab DETAIL 'B'
Streszczenie treści zawartej na stronie nr. 13
Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View Carefully unplug the power cord(s) of the E-Unit(s) from the timer assembly (see Front View) and unclip the power cord(s) from the clip(s) at the rear of cart. Loosen the screw holding the E-Unit bracket assembly and remove each bracket assembly (see DETAILS 'C
Streszczenie treści zawartej na stronie nr. 14
DETAIL 'C' DETAIL 'D' rear-left rear-right Step 3 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside.
Streszczenie treści zawartej na stronie nr. 15
cutout window rear-left rear-right clip Step 4 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top. When repositioned correctly, the E-Unit(s) power switch should be visible from rear panel cutout window. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the bracket assembly) and tighten screws securely. Plug in the E-Unit(s) power cord(s) into the bottom outlet(s) of th
Streszczenie treści zawartej na stronie nr. 16
tab notch Step 5 Reinstall the 9 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DETAIL 'E' Step 6 Reinstall 18 screws to rear panel that will secure the 9 interior shelves (see DETAIL 'E). DO NOT OVER TIGHTEN SCREWS. Installation is now complete and ready for
Streszczenie treści zawartej na stronie nr. 17
NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE STARTING E-UNIT REPLACEMENT: 'FRONT LOCATION' SEE DETAIL 'B' bottom shelf SEE DETAIL 'A' Step 1 Open both front doors of cart to access E-Unit(s). From underneath the bottom shelf, carefully unplug the power cord of the E-Unit(s) from the timer assembly (see Front View) and unclip the power cord(s) from the bottom of cart. Loosen the screw holding the E-Unit bracket assembly and remove (2) bracket assemblies of the E-Unit(s) to be
Streszczenie treści zawartej na stronie nr. 18
bracket bracket assembly assembly clip DETAIL 'B' DETAIL 'A' front-left front-right Step 2 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside.
Streszczenie treści zawartej na stronie nr. 19
front-left front-right bottom shelf Step 3 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting it in sideways to the top. When repositioned correctly, the E-Unit(s) power switch should face the front. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the bracket assembly) and tighten screws securely. Plug in the E-Unit power cord(s) into the bottom outlet(s) of the timer assembly (located unde
Streszczenie treści zawartej na stronie nr. 20
NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE STARTING TIMER REPLACEMENT: 'E-UNIT AT REAR LOCATION' DETAIL 'A' Step 1 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DETAIL 'A'). mounting tab DETAIL 'B'
