Streszczenie treści zawartej na stronie nr. 1
A&E CATALINA 2500
A&E Systems
USA
Service Office
The Dometic Corp.
509 South Poplar St.
LaGrange, IN 46761
CANADA
Dometic Dist.
866 Langs Dr.
Cambridge, Ontario
CANADA N3H 2N7
INSTALLATION & OPERATING Catalina
INSTRUCTIONS
2500
REVISION
Form No. 3103624.023 3/98
(Replaces 3103624.015)
(French 3108310.024)
©1998 The Dometic Corporation
1
LaGrange, IN 46761
Streszczenie treści zawartej na stronie nr. 2
A&E CATALINA 2500 A&E CATALINA 2500 Note: Awning must be mounted with case back parallel to INSTALLATION/OPERATION side wall of vehicle. APPLICATION The A&E Catalina 2500 Case Awning is designed and intended for direct mounting on straight and most curved mini-motorhomes, pick-up campers, vans, van conversions and pop-up tent trailers. The optional Universal Van Adapter Kit, A&E Part No. 930035 allows permanent or temporary mounting to vans with rain gutters without drilling holes in the van. Sh
Streszczenie treści zawartej na stronie nr. 3
A&E CATALINA 2500 Note: Positioning of left and right bottom mounting brack- ets should be at same level and centered to the awning arms (FIG. 6). 7. Loosen lock knob and extend arm assembly keeping arm perpendicular to awning case. Once location is determined, tighten lock knob (FIG. 7). Note: Make sure lock in top of awning arm assembly clears top of case lip (FIG. 4C). This is necessary for awning to open properly. Tighten lock knob. Repeat steps 4B & 4C for other side. C. Using wand, hook
Streszczenie treści zawartej na stronie nr. 4
A&E CATALINA 2500 Tighten lock knob. 13. A. On the back wall inside the awning case, measure in from edge of end cap 1 inch (2.54 cm) and up 1/2 Repeat Step 9B for other side. inch (1.27 cm) from bottom edge of back wall as Note: For curved sided vehicles skip to Step 13. shown in FIG. 13 and mark this location. B. Drill a 3/16 dia. hole through the back of the awning case and into the vehicle. Repeat for other side. 14. Secure case to vehicle using the two #14 Phillips pan head sheet metal sc
Streszczenie treści zawartej na stronie nr. 5
A&E CATALINA 2500 17. Using wand, check to see if awning opens and closes correctly by pulling awning open about 3 feet (1 meter) (FIG. 17). Note: For installation on some curved sided vehicles Step 18 does no apply. 18. When awning is at proper setting and operates cor rectly, mark location of arm setting on inner arm assem- bly with supplied arrow labels (FIG. 18). Repeat for other side. OPERATION INSTRUCTIONS B. Using wand, hook pull-strap and pull awning out TO OPEN about 1 meter (3 feet) (F
Streszczenie treści zawartej na stronie nr. 6
A&E CATALINA 2500 C. Tighten lock knob on arm assembly. FOR PATIO POSITION 5. Using wand, hook pull-strap and pull awning out by 6. Place arm assembly in a vertical position and adjust unrolling the fabric (FIGS. 5A and 5B). height (FIG. 6). 7. Drive in the supplied spikes through awning foot to secure arm to ground (FIG. 7). Repeat for other side. The Catalina 2500 Awning is now ready for you to enjoy. FULL EXTENSION During operation for fully extended awning, fabric can be rolled out and raft
Streszczenie treści zawartej na stronie nr. 7
A&E CATALINA 2500 TO CLOSE ON CURVED SIDED VEHICLE 3. Firmly grasp pull-strap and loosen lock knobs (FIG. 3A). While tightly holding pull-strap, pull on strap to relieve 6. IF AWNING IS SET IN PATIO POSITION: pressure from rafter lock buttons and push rafter lock A. Remove spikes from awning foot. buttons in to unlock rafters and allow awning to roll up B. Attach foot to bottom mounting bracket on side of (FIG. 3B). Make sure pull-strap is centered in awning vehicle to set awning into pivot pos
Streszczenie treści zawartej na stronie nr. 8
A&E CATALINA 2500 AWNING UNLOCKED the awning case. Note: Make sure lock in top of awning arm assembly engages case lip (FIG. 7G). If lock does not engage case lip, raise arm height until lock clears lip and then engages. This is necessary for proper operation of awning case locks. E. Loosen lock knob on arm assembly (FIG. 7H). Repeat for other side. 8. Insert pin at end of wand, through hole in outer arm so it aligns foot for easy storage (FIG. 8A). Swing arm up to case (FIG. 8B). Slide arm a
