Streszczenie treści zawartej na stronie nr. 1
a
Uni-Drill
10 mm (3/8") MODEL 6000LR
INSTRUCTION MANUAL
DOUBLE
INSULATION
SPEC I FI CAT IO N S
CaDacities
No load
Overall Net
Machine & wood screws
~~~~ 1 length I weight
~~~~~ Self drilling screws
(steel)
Bolts & Nuts, Tapper
* Manufacturer reserves the right to change specifications without notice.
* Note: Specifications may differ from country to country.
Streszczenie treści zawartej na stronie nr. 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence
Streszczenie treści zawartej na stronie nr. 3
13. DISCONNECT TOOLS. When not in use, before servicing, and when chang- ing accessories, such as blades, bits, cutters. 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for
Streszczenie treści zawartej na stronie nr. 4
ADDITIONAL SAFETY RULES 1. Always be sure you have a firm footing. Be Sure no one is below when using the tool in high locations. 2. Hold the tool firmly. 3. Keep hands away from rotating parts. 4. When drilling into walls, floors or wherever "live" electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool by the insulated grasping surfaces to prevent electric shock if you drill into a "live" wire. 5. Do not leave the tool running. Operate the tool onl
Streszczenie treści zawartej na stronie nr. 5
Selecting action mode 1 For drilling, turn the change ring so that the red dot is aligned with the DRILL marking on the collar. If the change ring will not come all the way, grasp the chuck and turn the change ring again. Do not move the red dot beyond the DRILL mark- ing. For screwdriving, turn the change ring so that the red dot is aligned with the SCREW marking on the collar. Do not move the red CAUTION : If you use the tool when the red dot is not I aligned with either marking,
Streszczenie treści zawartej na stronie nr. 6
Installing or removing drill bit or driver bit CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the bit. To install the bit, place it in the chuck as far as it will go. Tighten the chuck by hand. Chuck key Tiahten Place the chuck key in each of the three holes and tighten clockwise. Be sure to tighten all three chuck holes evenly. To remove the bit turn the chuck key counterclockwise in just one hole, then loosen the chuck by hand.
Streszczenie treści zawartej na stronie nr. 7
Reversing switch action This tool has a reversing switch to change the direction of rotation. Move the revers- ing switch lever to the "F" position for clockwise rotation or the "R" position for counterclockwise. Reversing switch lever I CAUTION : 0 Always check the direction of rotation before drilling. Use the reversing switch only when the tool comes to a complete stop. Changing the direction of rotation before the tool stop may ruin the tool. Drilling operation Turn the change r
Streszczenie treści zawartej na stronie nr. 8
Screwdriving operation Turn the change ring so that the red dot is aligned with the SCREW marking. Place the point of the driver bit in the screw head and apply pressure to the tool. When driving screws, start the tool slowly and then increase the speed gradually. NOTE : When driving small screws, be careful not to damage the screw heads. Ease pressure on the tool as soon as the screws bottom out. 0 Make sure that the driver bit is inserted straight in the screw head, or the screw and/
Streszczenie treści zawartej na stronie nr. 9
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Chuck key SI0 0Grip 26 Part No. 763412-5 Part No. 273485-5 9
Streszczenie treści zawartej na stronie nr. 10
Oec.-20-83 US 10 mm (3/8") UNI-DRILL Model 6000LR Note: The switch, noise suppressor and other part configurations may differ from country to country. 10
Streszczenie treści zawartej na stronie nr. 11
MODEL 6000LR Apr -07-'88 US ITEM NO. DESCRIPTION $ED DESCRIPTION NO. USED MACHINE MACHINE ~ ~ 1 1 Drill Chuck S10 24 1 ARMATURE ASSEMBLY [With Item 21 23 311 2 1 Change Ring 3 1 0 Ring 27 25 1 Baffle Plate 26 2 Hex Bolt M4x45 [With Washerl 4 1 Gear Housing 1 Flat Washer 16 21 1 FIELD ASSEMBLY 5 6 1 Spindle 28 1 Leaf sprmg 1 1 Compression Spring 9 29 1 Hook 8 1 Helical Gear 56 30 1 Motor Housing 31 1 Ball Bearing 627L8 9 1 Woodruff Key 3 10 1 Gear Shaft 32 1 Rubber Pin 4 2 Car
Streszczenie treści zawartej na stronie nr. 12
1’ MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, retum the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or ma
